ignition MERCEDES-BENZ S CLASS 2007 Owner's Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: S CLASS, Model: MERCEDES-BENZ S CLASS 2007Pages: 705, PDF Size: 9.84 MB
Page 363 of 705
362 Controls in detailDriving and parking
For more information, see “Driving instruc-
tions” (
page 479).
Turn signalsCombination switch1Turn signals, right
2Turn signals, left
Press the combination switch up1 or
down2.
The corresponding turn signal indicator
lampL orK flashes in the in-
strument cluster (
page 28).
The combination switch resets automati-
cally after major steering wheel move-
ments.
Problems while driving
The engine runs erratically and misfires
An ignition cable may be damaged.
The engine electronics may not be op-
erating properly.
Unburned gasoline may have entered
the catalytic converter and damaged it.
Give very little gas.
Warning!
G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced vehi-
cle control. Your vehicle’s ABS will not pre-
vent this type of loss of control.Warning!
G
It is dangerous to shift the gear selector le-
ver out of P or N if the engine speed is high-
er than idle speed. If your foot is not firmly
on the brake pedal, the vehicle could accel-
erate quickly forward or in reverse. You
could lose control of the vehicle and hit
someone or something. Only shift into gear
when the engine is idling normally and when
your right foot is firmly on the brake pedal.!
Shift the automatic transmission toP or R
only when the vehicle is stopped in order to avoid
damaging the transmission.
!
Do not run cold engine at high engine
speeds. Running a cold engine at high engine
speeds may shorten the service life of the en-
gine.
!
Simultaneously depressing the accelerator
pedal and applying the brake reduces engine
performance and causes premature brake and
drivetrain wear.
i
To signal minor directional changes, e.g.
passing or changing lanes, move combination
switch to point of resistance only and release.
The corresponding turn signal flashes three
times.
Page 365 of 705
364 Controls in detailDriving and parkingElectric parking brake
1Handle for electric parking brake
Manually releasing electric parking
brake
Pull handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster goes out.
You cannot release the electric parking
brake until the ignition is switched on.Automatically releasing electric parking
brake
Your vehicle’s electric parking brake is au-
tomatically released when:
The engine is running.
Transmission is in position D or R.
The hood is closed.
You have fastened your seat belt.
You step on the accelerator pedal.
If gear R is engaged, the trunk must be
closed.
Warning!
G
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could release the parking brake
and/or shift the automatic transmission out
of position P, either of which could result in
an accident and/or serious personal injury.Warning!
G
Getting out of your vehicle with the automat-
ic transmission not fully engaged in
positionPis dangerous. Also, when parked
on an incline, position P alone may not pre-
vent your vehicle from moving, possibly hit-
ting people or objects.
Always set the parking brake in addition to
shifting to position P (
page 359).
i
If you have not fastened your seat belt, the
following conditions must be met in order for the
parking brake to be automatically released:
The driver's door is closed
You must move the gear selector out of P po-
sition or drive faster than 2 mph (3 km/h).
Page 367 of 705
366 Controls in detailDriving and parking
Shift the automatic transmission toP.
Turning off with SmartKey
Turn the SmartKey in the starter switch
to position0 (
page 315) and remove
it.
The immobilizer is activated.Turning off with KEYLESS-GO*
Press the KEYLESS-GO start/stop
button (
page 317) to turn off the en-
gine.
With the driver’s door closed, the start-
er switch is now in position1. With the
driver’s door opened, the starter switch
is set to position0, same as SmartKey
removed from starter switch
(
page 315).
Releasing seat belts
Press the seat belt release button
(page 340).
Allow the retractor to completely re-
wind the seat belt by guiding the latch
plate.
headlamps are switched on.
The message: “Please switch off lights” appears
in the multifunction display.i
When parked on an incline, also turn front
wheels towards the road curb.
i
If the engine can no longer be stopped using
the SmartKey or KEYLESS-GO*, the engine can
be turned off by withdrawing two fuses. For more
information, see “Emergency engine shut-down”
(
page 648).
i
If you turn off the engine using the SmartKey
and remove the SmartKey from the starter
switch with the automatic transmission in a posi-
tion other than P, the transmission will automat-
ically shift toP.
Keep in mind that turning off the engine with the
SmartKey alone will not automatically shift the
transmission to P.Only when the SmartKey is removed from the
starter switch will the transmission automatical-
ly shift to P.
i
In an emergency you can turn off the engine
while driving by pressing and holding the
KEYLESS-GO start/ stop button for approxi-
mately 3 seconds.
i
If you turn off the engine using the
KEYLESS-GO start/stop button and open the
driver’s door with the automatic transmission in
a position other than P, the transmission will au-
tomatically shift toP.Keep in mind that turning off the engine with the
KEYLESS-GO start/stop button alone will not au-
tomatically shift the transmission to P. Only
when the driver’s door is opened will the trans-
mission automatically shift to P.
i
If you drive through an automatic conveyor
type car wash, you can switch on the ignition
with the KEYLESS-GO button and engage gear N
or insert the SmartKey into the starter switch.
!
M a k e s u r e t h e s e a t b e l t r e t r a c t s f u l l y s o t h a t
the seat belt and/or latch plate cannot get
caught or pinched in the door or in the seat
mechanism. This can damage the seat belt and
impair the effectiveness of the seat belt, and/or
cause damage to the door and/or door trim pan-
el. Such damage is not covered by the
Mercedes-Benz Limited Warranty.
Damaged seat belts must be replaced. Contact
an authorized Mercedes-Benz Center.
Page 379 of 705
378 Controls in detailInstrument clusterA full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 28).
The instrument cluster is activated when
you:
open a door
switch on the ignition (
page 315)
switch on the exterior lamps
The language setting for the multifunction
display can be changed via COMAND
(
page 79).Adjusting instrument cluster and
COMAND display illumination
1To adjust instrument cluster illumina-
tion and multifunction display
2To adjust COMAND display
Brightening illumination: Turn
knob1 or2 clockwise.
Dimming illumination: Turn knob1
or2 counterclockwise.
Coolant temperature gauge
Warning!
G
No messages will be displayed if either the
instrument cluster or the multifunction dis-
play is inoperative.
As a result, you will not be able to see infor-
mation about your driving conditions, such
as speed or outside temperature, warning/
indicator lamps, malfunction/warning mes-
sages or the failure of any systems. Driving
characteristics may be impaired.
If you must continue to drive, please do so
with added caution. Visit an authorized
Mercedes-Benz Center as soon as possible.i
The instrument cluster illumination is
dimmed or brightened automatically to suit am-
bient light conditions.
The instrument cluster illumination will also be
adjusted automatically when you switch on the
vehicle’s exterior lamps.
Warning!
G
Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.
Steam from an overheated engine can
cause serious burns and can occur just
by opening the hood. Stay away from
the engine if you see or hear steam com-
ing from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
Page 406 of 705
405 Controls in detail
Driving systems
Parktronic system*
Parktronic is an electronic parking aid with
ultrasonic sensors that helps you while
parking.
It visually and audibly indicates the relative
distance between the vehicle and an ob-
stacle.
Parktronic is automatically activated when
you switch on the ignition, release the
electric parking brake or start the engine
and engage gear D, R or N.The Parktronic system deactivates at
speeds over approximately 11 mph
(18 km/h). At lower speeds the Parktronic
system turns on again.
Parktronic is also switched off when you
engage gear P or secure the vehicle in
place with the electric parking brake and
switch off the engine.
The Parktronic system monitors the sur-
roundings of your vehicle with six sensors
in the front bumper and four sensors in the
rear bumper.
1Sensors in the front bumper (Only visi-
ble without DISTRONIC Plus*)Warning!
G
Parktronic is a supplemental system. It is
not intended to, nor does it replace, the
need for extreme care. The responsibility
during parking and other critical maneuvers
always rests with the driver.
Special attention must be paid to objects
with smooth surfaces or low silhouettes
(e.g. trailer couplings, painted posts, or road
curbs). Such objects may not be detected by
the system and can damage the vehicle.
The operational function of the Parktronic
system can be affected by dirty sensors, es-
pecially at times of snow and ice, see
“Cleaning the Parktronic* system sensors”
(page 538).
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.i
Interference caused by other ultrasonic sig-
nals (e.g. working jackhammers, car wash, or the
air brakes of trucks) can cause the system to
send erratic indications, and should be taken
into consideration.
Page 409 of 705
408 Controls in detailDriving systemsSwitching Parktronic system on/off
The Parktronic system can be switched off
manually.
The Parktronic button with the indicator
lamp is on the control panel on the
right-hand side of the instrument cluster.
1Parktronic button
2Indicator lamp
Switching off the Parktronic sys-
tem: Press button 1.
Indicator lamp 2 comes on.
Switching on the Parktronic system:
Press button 1 again.
Indicator lamp 2 goes out.
Parktronic system malfunction
If only the red distance segments illumi-
nate and an acoustic warning sounds,
there is a malfunction in the Parktronic
system. The Parktronic system will auto-
matically switch off after 20 seconds and
the indicator lamp in the Parktronic switch
comes on.
Have the Parktronic system checked
by an authorized Mercedes-Benz Cen-
ter as soon as possible.
If only the red distance segments illumi-
nate and no acoustic warning sounds, the
Parktronic system sensors are dirty or
there is an interference from other radio or
ultrasonic signals. The Parktronic system
will automatically switch off after 20 sec-
onds and the indicator lamp in the Park-
tronic switch comes on.
Switch off the ignition (
page 315).
Clean the Parktronic system sensors
(page 538).
Switch on the ignition.
or
Check the Parktronic system operation
at another location to rule out interfer-
ence from outside radio or ultrasonic
signals.
i
The Parktronic system is automatically
switched on when the ignition is switched on
(
page 315).
Page 413 of 705
412 Controls in detailDriving systemsCollision warning
Park Assist can detect obstacles from a
considerable distance. If you drive in re-
verse towards an obstacle, you will hear a
warning tone. You must then brake in or-
der to avoid a collision. The warning tone
for a collision will not sound when the vehi-
cle is at a standstill very close to the obsta-
cle. In this case, you will hear a
corresponding tone for the warning indica-
tor in the rear area.Switching Park Assist system on/off
The Park Assist system can be switched off
manually.
The Park Assist button with the indicator
lamp is located on the control panel on the
right-hand side of the instrument cluster.
1Park Assist button
2Indicator lamp
Switching off Park Assist system:
Press button 1.
Indicator lamp 2 comes on.
Switching on Park Assist system:
Press button 1 again.
Indicator lamp 2 goes out.
i
During strong rainfall, the collision warning
may be triggered, for example, by water splash-
ing into the area of the sensors.
i
When the indicator lamp is on, the Park
Assist system is switched off.
i
The Park Assist system is automatically
switched on when the ignition (
page 315) and
radar sensors are switched on (page 256).
Page 416 of 705
415 Controls in detail
Driving systems
Switching on Dynamic Rear View Moni-
tor
Switch on the ignition (
page 315).
Switch on COMAND (
page 79).
Move gear selector lever to position R
(reverse gear).
The COMAND display will show the
area behind the vehicle with guide lines
to help you reverse into a parking
place.
Reverse parking (back-in parking)This function helps you when you are re-
versing in a straight line or backing in at
any angle.
The space required by the vehicle for re-
versing is shown by guide lines.
When you turn the steering wheel to a
straight-ahead position, you will see the
guide lines on the COMAND display in the
following order:
1Yellow and blue guide lines for vehicle
width
2Yellow 13 ft (4 m) guide line
3Yellow 39 in (1 m) guide line
4Red 10 in (0.25 m) guide line
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Dynamic Rear
View Monitor. Contact an authorized
Mercedes-Benz Center.Warning!
G
Use of Dynamic Rear View Monitor can be
dangerous if you are color-blind or have im-
paired color vision.
Only use Dynamic Rear View Monitor if you
can see and distinguish all colored guide
lines shown by Dynamic Rear View Monitor
on the COMAND display.i
The Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 253).
i
If you activate a different function on the
driver’s COMAND controls while reverse parking
or parallel parking, the image from the back-up
camera is interrupted.
To reactivate the camera, take the vehicle out of
reverse gear and then re-engage reverse gear
again.
Page 417 of 705
416 Controls in detailDriving systemsThe red 10 in (0.25 m) guide line4, the
yellow 39 in (1 m) guide line3 and the
yellow 13 ft (4 m) guide line2 correspond
to the relevant distance from the rear of
the vehicle. The yellow and blue guide lines
for vehicle width1 show the required
width for the vehicle.
5Blue guide lines for straight driving
6Symbol for “reverse parking”
7Yellow and red guide lines for cornering
When you turn the steering wheel out of
the straight-ahead position, the positions
of the yellow and red guide lines7
change depending on the steering wheel’s
position. The space required by the vehicle
for reverse cornering is indicated by yellow
and red guide lines7.Backing in straight
Switch on the ignition (
page 315).
Switch on COMAND (
page 79).
Move gear selector lever to position R
(reverse gear).
Use the COMAND controller
(page 82) to select “reverse parking”
function 6.
You will see the guide lines for reverse
parking on the COMAND display.
The desired parking space is wide
enough if nothing is inside the yellow
and blue guide lines1 of your intend-
ed driving path or protrudes into this
area.
Back in straight carefully.
Warning!
G
Please note that objects which do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck, may appear to be further
away than they actually are. In this case, you
should not use the guide lines to judge dis-
tance as the use of the guide lines to judge
distance increases the risk of impacting the
objects.
Even when the object you approach is di-
rectly on the ground (and nothing on the ob-
ject extends above the ground beyond the
object's contours directly touching the
ground) and no objects that do not touch
the ground, such as the bumper of a vehicle
parked behind you, a trailer hitch, or the
back of a truck are in the path, do not ap-
proach the object on the ground any closer
than red guide line4.
i
The Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 253).
!
While parking, do not approach any obsta-
cles closer than indicated by red guide line4.
Page 418 of 705
417 Controls in detail
Driving systems
Backing in at any angle
Switch on the ignition (
page 315).
Switch on COMAND (
page 79).
Move gear selector lever to position R
(reverse gear).
Use the COMAND controller
(page 82) to select “reverse parking”
function6.
You will see the guide lines for reverse
parking on the COMAND display.
Turn steering wheel so that the yellow
and red guide lines for cornering7 are
pointing towards the desired parking
space.
The desired parking space is wide
enough if nothing is inside yellow and
red guide lines7 of your intended
driving path or protrudes into this area.
Back in carefully.
When the blue guide lines5 for
straight driving lie parallel inside the
desired parking space, straighten the
steering wheel for straight driving.
Back in enough to leave sufficient free
space around the vehicle.
Parallel parking
This function assists you when you wish to
park in a row, e.g. in a parking place paral-
lel to the road.
Stop the vehicle
at a distance of approximately
three feet (one meter) parallel to
the vehicle that is in front of the de-
sired parking space.
in such a way that the front of the
parked vehicle is parallel to your
rear wheel.
Switch on COMAND (
page 79).
Move gear selector lever to position R
(reverse gear).
1Vertical blue guide line
2Symbol for “parallel parking”
i
The Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 253).
!
While parking, do not approach any obsta-
cles closer than indicated by red guide line4.
i
The Dynamic Rear View Monitor must be ac-
tivated in the instrument cluster control system
in order for it to be switched on (
page 253).