warning light MERCEDES-BENZ S CLASS 2007 Service Manual

580 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Parking brake
See Oper. Manual
If overheated:
Let vehicle cool down, and do not engage
electric parking brake during this time.
or

Switch ignition off and back on again, and en-
gage or release electric parking brake.
(USA only)(Canada only)
Parking brake
inoperative
When you engage or release the electric
parking brake, the red indicator lamp for
the electric parking brake flashes and goes
out after approx. 10 seconds. The yellow
warning lamp for the electric parking brake
lights up.
The electric parking brake is malfunction-
ing.

Switch ignition off and back on again, and en-
gage electric parking brake (
page 364).
If the electric parking brake cannot be engaged:

Shift the automatic transmission to P
(page 367).

Protect vehicle from rolling away while
parked by using a chock from the vehicle tool
kit (
page 613).

Visit an authorized Mercedes-Benz Center as
soon as possible.

585 Practical hints
What to do if …?
Display
Possible cause/consequence
Possible solution
STOP,
car too low
You have started driving although the vehi-
cle level was too low.
The vehicle will be raised. The Airmatic*
warning lamp goes out after several sec-
onds.

Stop your vehicle as soon as it is safe to do
so.

Wait until the message disappears from the
multifunction display.
You may then drive off.
STOP,
car too low
The Airmatic* is malfunctioning.
The Airmatic* warning lamp lights up con-
tinuously.

Stop and press the vehicle level control but-
ton to select a higher vehicle level
(page 401).

Do not turn steering wheel too far to avoid
damaging the front fenders.

Listen for scraping noises.

Do not exceed a speed of 50 mph (80 km/h).

Visit an authorized Mercedes-Benz Center as
soon as possible.
There is otherwise danger of an accident.
Malfunction
The capability of the Airmatic* system is re-
stricted. This can impair the handling.

Do not exceed a speed of 50 mph (80 km/h).

Visit an authorized Mercedes-Benz Center as
soon as possible.

623 Practical hints
Replacing bulbs
Notes on bulb replacement


Only use 12-volt-bulbs of the same
type and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not
come on, visit an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center.


the Bi-Xenon lamps


the front turn signal lamps


the front fog lamps


the additional turn signal lamps in the
exterior rear view mirrors


the parking and standing lamps


the front side marker lamps


the high mounted brake lamps


the brake, tail and rear standing lamps


the rear side marker lamps


the rear fog lamp


the rear turn signal lamps


the rear side marker lamps


the license plate lamps
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to M
(page 342).

Open the hood (
page 492) (except
for side marker lamps).
Warning!
G
Keep bulbs out of reach of children.
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
i
Have the headlamp adjustment checked
regularly.

632 Practical hintsFlat tire
Replace this wheel bolt with alignment
bolt1 supplied in the tool kit.

Remove the remaining bolts.

Remove the wheel.
Mounting the Minispare wheel
1Wheel bolt for light alloy rims
2Wheel bolt for Minispare wheel
(located in trunk with spare wheel)

Clean contact surfaces of wheel and
wheel hub.

Guide the Minispare wheel onto the
alignment bolt and push it on.

Insert wheel bolts2 and tighten them
slightly.
!
Do not place wheel bolts in sand or dirt. This
could result in damage to the bolt and wheel hub
threads.
!
Wheel bolts2 must be used when mount-
ing the Minispare wheel. The use of any wheel
bolts other than wheel bolts2 for the Minispare
wheel will physically damage the vehicle’s
brakes.
Warning!
G
Make sure to use the original length wheel
bolts when remounting the original wheel
after it has been repaired.!
To avoid paint damage, place wheel flat
against hub and hold it there while installing first
wheel bolt.
Warning!
G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be re-
paired immediately. Do not continue to drive
under these circumstances! Contact an au-
thorized Mercedes-Benz Center or call
Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure you are using the correct wheel
bolts.


633 Practical hints
Flat tire

Unscrew the alignment bolt, install the
last wheel bolt and tighten slightly.Lowering the vehicle

Lower vehicle by turning crank coun-
terclockwise until vehicle is resting ful-
ly on its own weight.

Remove the jack.
1 - 5 Wheel bolts

Tighten the five wheel bolts evenly, fol-
lowing the diagonal sequence illustrat-
ed (1 to 5), until all bolts are tight.
Observe a tightening torque of
110 lb-ft (150 Nm).Before storing the jack, it should be fully
collapsed, with handle folded in (storage
position).

Store the jack and the other vehicle
tools in the designated storage space
underneath the trunk floor
(page 611).
Warning!
G
Only use Genuine equipment
Mercedes-Benz wheel bolts. Other wheel
bolts may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
fall off the jack.
Warning!
G
Have the tightening torque checked after
changing a wheel. The wheels could come
loose if they are not tightened to a torque of
110 lb-ft (150 Nm).i
Do not activate the tire inflation pressure
monitor (
page 511) until the depressurized
tire has been removed from the trunk.

640 Practical hintsJump startingJump starting should only be performed on
the starter battery. The starter battery is
located in the engine compartment on the
passenger side (
page 634).

Make sure the two vehicles do not
touch.

Secure vehicle in place with electric
parking brake.

Shift the automatic transmission toP.

Turn off all electrical consumers, ex-
cept hazard warning flashers or work
lights.

Open the hood (
page 492).

Start the engine of the vehicle with the
charged battery and run at idle speed.1Positive terminal of your vehicle’s
battery
2Positive terminal of other vehicle’s
battery
3Negative terminal of other vehicle’s
battery
4Negative clamp
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 634).
i
Vehicles with KEYLESS-GO: remove the
KEYLESS-GO button (
page 316) and use the
SmartKey with KEYLESS-GO like a normal
SmartKey.

664 Technical dataFuels, coolants, lubricants, etc.Premium unleaded gasoline
Fuel requirements
Use only premium unleaded fuel:

The octane number (posted at the
pump) must be 91 min. It is an average
of both the Research (R) octane num-
ber and the Motor (M) octane number:
(R+M)/2). This is also known as the
ANTI-KNOCK INDEX.
Unleaded gasoline containing oxygenates
such as ethanol, IPA, IBA and TBA can be
used provided the ratio of any one of these
oxygenates to gasoline does not exceed
10%; MTBE must not exceed 15%.
The ratio of methanol to gasoline must not
exceed 3% plus additional co-solvents.
Using mixtures of ethanol and methanol is
not allowed. Gasohol, which contains
10% ethanol and 90% unleaded gasoline,
can be used.
These blends must also meet all other fuel
requirements, such as resistance to spark
knock, boiling range, vapor pressure, etc.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Whenever you are around gasoline,
avoid inhaling fumes and skin contact, extin-
guish all smoking materials. Never allow
sparks, flame or smoking materials near
gasoline!
Switch off the engine before refueling.Warning!
G
Do not allow fuel to come into contact with
skin or clothing.
Direct skin contact with fuels and the inha-
lation of fuel vapors are damaging to health.
!
To maintain the engine’s durability and per-
formance, premium unleaded gasoline must be
used. If premium unleaded gasoline is not avail-
able and low octane fuel is used, follow these
precautions:


Have the fuel tank only partially filled with
unleaded regular and fill up with premium
unleaded as soon as possible.


Avoid full throttle driving and abrupt acceler-
ation.


Do not exceed an engine speed of 3000 rpm
if the vehicle is loaded with a light load such
as two persons and no luggage.


Do not exceed
2/3 of maximum accelerator
pedal position if the vehicle is fully loaded or
operating in mountainous terrain.

674 Technical termsInstrument cluster
The displays and indicator/warning
lamps in the driver’s field of vision, in-
cluding the tachometer, speedometer,
engine temperature and fuel gauge.
ISO9660
A standard file system for recording
data on CDs.
Joliet
Standard for recording data on CDs; an
extension of ISO 9660.
KEYLESS-GO*
System for entering and operating the
vehicle without the use of a SmartKey.
Kickdown
Depressing the accelerator past the
point of resistance shifts the transmis-
sion down to the lowest possible gear.
This very quickly accelerates the vehi-
cle and should not be used for normal
acceleration needs.Kilopascal (kPa)
(
page 527)
LED
(Light E
mitting D
iode)
Semiconductor element that converts
electricity directly into light.
Line of fall
The direct line that an object moves
downhill when influenced by the force
of gravity alone.
LOGIC7
® surround
Multichannel surround technology
from the professional audio industry
that plays back 5.1 and stereo record-
ings in surround sound. LOGIC7
® cre-
ates a natural 360° sound experience
on all seats.
Locking knob
Knob on the door which indicates
whether the door is locked or un-
locked. Pushing the locking knob down
on an individual door from inside will
lock that door.Maintenance System (U.S. vehicles)
Maintenance service indicator in the
->multifunction display that informs the
driver when the next vehicle mainte-
nance service is due. The Maintenance
System in your vehicle tracks distance
driven and the time elapsed since your
last maintenance service, and calls for
the next maintenance service accord-
ingly.
Maximum load rating
(
page 527)
Maximum loaded vehicle weight
(page 527)
Maximum tire inflation pressure
(page 527)
Memory function
Used to store three individual seat,
steering wheel and exterior mirror posi-
tions.

683 Index
Corner-illuminating lamps 347
Courtesy lighting 350
Cruise control 380, 671
Activating 381
Canceling 382
Driving downhill 382
Driving uphill 382
Message in display 559
Setting current speed 381
Setting to last stored speed (“Resume”
function) 384
Cup holder
Cleaning 541
In front seat armrest 452
In rear seat armrest 452
Curb weight 526, 671
Customer Assistance Center see CAC
D
Date
Setting (COMAND) 214
Daytime running lamp mode 344
Deceleration
With DISTRONIC Plus* 388
Deep water see Standing water
Defrosting 429Delayed switch-off
Exterior lighting (COMAND) 220
Interior lighting (COMAND) 226
Department of Transportation see DOT
Destination entry (COMAND) 153
Destination memory (COMAND) 195
Difficulties
While driving 362
While starting 360
Digital speedometer 246
Additional speedometer 255
Dimensions, Vehicle 660
Direction of rotation, Tires 503
Displays
Additional speedometer 255
Digital speedometer 246
DISTRONIC Plus* 387
Maintenance service indicator 532
Multifunction display 241
Vehicle status message see Multifunc-
tion display messages
Distance
Decreasing in DISTRONIC Plus* 397
Increasing in DISTRONIC Plus* 396
Setting in DISTRONIC Plus* 396
Distance to Empty (Range) 246Distance warning function*
Activating 397
Deactivating 397
Distance warning lamp 397
Intermittent warning sound 397
DISTRONIC Plus* 385
Activated 389
Activating 390
Calling up settings 389
Cleaning system sensor 537
Deactivated 389
Deactivating 395
Deceleration 388
Decreasing distance 397
Decreasing time interval 396
Displays in the speedometer dial 387
Distance warning function 397
Driving hints 397
Increasing distance 396
Increasing time interval 396
Intermittent signal tone 388
Lever 390
Menu 389
Messages in display 560
Sensor cover 537
Setting a higher speed 393

684 Index
Setting a slower speed 394
Setting following distance 396
Setting the current speed 393
Setting to last stored speed (“Resume”
function) 395
Warning and indicator lamps 388
Warning lamp 549
Document holder 455
Door
Control panel 38, 39, 42
Entry lamps 350
Inside door handle 312
Locking 305, 309
Locking with Tele Aid 469
Messages in display 562, 590
Opening from inside vehicle 312
Opening from outside 305, 309
Power closing assist 313
Unlocking 305, 309
Unlocking with Tele Aid 468
DOT 526
Downhill driving
Cruise control 382
Drink holder see Cup holder
Drinking and driving 479Drive-dynamic multicontour seats*, front
Adjusting (COMAND) 240
Driving 359
Abroad 486
Hydroplaning 483
In winter 484
Instructions 359, 479
Problems 362
Safety systems 69
Through standing water 485
With DISTRONIC Plus* 397
Driving maneuver (COMAND) 185
Driving off 481
Driving safety systems
ABS 69
Adaptive Brake Lights (S 600 and USA
only) 70
BAS 71
BAS Plus 71
EBP 71
ESP
®
72
ETS 73Driving systems 380
ABC* 403
Airmatic 401
Cruise control 380
DISTRONIC Plus* 385
Driving safety systems 69
Dynamic Rear View Monitor* 413
Park Assist* 409
Parktronic system* 405
Vehicle level control (ABC*) 403
Vehicle level control (Airmatic) 401
Driving tips 373
Kickdown 373
DVD 104
Audio (COMAND) 104
Changer (COMAND) 107
Changer (Voice Control*) 286
Ejecting (COMAND) 109
Loading (COMAND) 107
Playback options (COMAND) 114
Selecting a medium (COMAND) 112
Selecting a track (COMAND) 113
Setting the audio format
(COMAND) 114