rear view mirror MERCEDES-BENZ S-Class 2008 W221 Comand Manual

543 Controls in detail
Useful features
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and mo-
bile phone and GPS coverage are available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the COMAND
volume thumbwheel , on the lower
part of the front center console
(page 98).

To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.
System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated.
If a malfunction is detected, the indicator
lamps in the SOS button, the Roadside As-
sistance button• and the Information
button¡ stay on longer than
10 seconds or do not come on. The mes-
sage “Tele Aid Not Activated” or “Tele Aid
Inoperative” appears in the multifunction
display.
i
The Tele Aid system utilizes the mobile
phone network for communication and the GPS
(Global Positioning System) satellites for vehicle
location. If either of these signals are unavail-
able, the Tele Aid system may not function and if
this occurs, assistance must be summoned by
other means.
i
The SOS button is located above the interior
rear view mirror (
page 545).
The Roadside Assistance button• and the
Information button¡ are located below the
center armrest cover (page 546).
Warning!
G
If the indicator lamps in the SOS button, in
the Roadside Assistance button•
and/or in the Information button¡ do
not come on during the system self-check,
or if any of these indicators remain illuminat-
ed continuously in red and/or the message
“Tele Aid Not Activated” or “Tele Aid Inoper-
ative” is displayed in the multifunction dis-
play after the system self-check, a
malfunction in the system has been detect-
ed.
If a malfunction is indicated as outlined
above, the system may not operate as ex-
pected. Have the system checked at the
nearest Mercedes-Benz Center as soon as
possible.

544 Controls in detailUseful featuresEmergency calls
An emergency call is initiated
automatically following an accident in
which the emergency tensioning devices
(ETDs) or air bags deploy.
An emergency call can also be initiated
manually by opening the cover next to the
interior rear view mirror labeled SOS, then
briefly pressing the button located under
the cover. For instructions on initiating an
emergency call manually (
page 545).
Once the emergency call is in progress, the
indicator lamp in the SOS button will begin
to flash. The message:


“Connecting Call” appears in the multi-
function display


“Emergency Call Activated” appears in
the COMAND display
and the audio system is muted. When the
connection is established, the message:


“Call Connected” appears in the multi-
function display


“Emergency Call Activated” appears in
the COMAND display
All information relevant to the emergency,
such as the location of the vehicle (deter-
mined by the GPS satellite location sys-
tem), vehicle model, identification number
and color are generated.
A voice connection between the Response
Center and the occupants of the vehicle
will be established automatically soon af-
ter the emergency call has been initiated.
The Response Center will attempt to deter-
mine more precisely the nature of the acci-
dent provided they can speak to an
occupant of the vehicle.The Tele Aid system is available if


it has been activated and is operation-
al. Activation requires a subscription
for monitoring services, connection,
and cellular air time


the relevant monitoring service and
GPS coverage are available and pass
the information on to the Response
Center


there is sufficient voltage in the vehicle
batteries
i
During the emergency call message “Emer-
gency Call Activated” is displayed, operation
from COMAND is not possible. The automatic cli-
mate control can be still adjusted using the
switches on the climate control panel.
i
If no vehicle occupant responds, an ambu-
lance will be sent to the vehicle immediately.
i
Location of the vehicle on a map is only pos-
sible if the vehicle is able to receive signals from
the GPS satellite network and pass the informa-
tion on to the Response Center.Warning!
G
If the indicator lamp in the SOS button is
flashing continuously and there was no
voice connection to the Response Center
established, then the Tele Aid system could
not initiate an emergency call (e.g. the rele-
vant mobile phone network is not available).

551 Controls in detail
Useful features
Garage door opener
The integrated remote control is capable of
operating up to three separately controlled
devices. It provides a convenient way to re-
place up to three hand-held remote con-
trols used to operate devices such as
garage door openers, gate openers, or oth-
er devices compatible with HomeLink
® or
some other systems.
Before the integrated remote control can
be used, it must be programmed to the ga-
rage door opener, gate operator or other
device you wish to operate. See the follow-
ing instructions for programming informa-
tion.
Interior rear view mirror with integrated
remote control1Indicator lamp
2 3 4Signal transmitter button
Needed for programming (not part of vehi-
cle equipment):
5Hand-held remote control of ga-
rage door opener, gate operator
or other device
6Hand-held remote control
button
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate
operator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage. When programming
a garage door opener, the door moves up or
down. When programming a gate operator,
the gate opens or closes.
Do not use the integrated remote control
with any garage door opener that lacks
safety stop and reverse features as required
by U.S. federal safety standards (this
includes any garage door opener model
manufactured before April 1, 1982).
A garage door that cannot detect an object
– signaling the door to stop and reverse –
does not meet current U.S. federal safety
standards.
When programming a garage door opener,
park the vehicle outside the garage.


617 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment,
make sure to protect electrical compo-
nents and connectors from contact with
water and cleaning agents.
Corrosion protection, such as
MB Anticorrosion Wax, should be applied
to the engine compartment after every
engine cleaning. Before applying, all
control linkage bushings and joints should
be lubricated. The poly-V-belt and all pul-
leys should be protected from any wax.
Vehicle washing
In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the vehicle underbody, do
not forget to clean the inner sides of the
wheels.Hand-wash
Do not use hot water or wash your vehicle
in direct sunlight.

Only use a mild car wash detergent,
such as Mercedes-Benz approved Car
Shampoo.

Thoroughly spray the vehicle with a dif-
fused jet of water.
Direct only a very weak spray towards
the ventilation intake.

Use plenty of water and rinse the
sponge and chamois frequently.

Rinse with clean water and thoroughly
dry with a chamois.
Do not allow cleaning agents to dry on
the finish.Automatic car wash
You can have your car washed in an auto-
matic car wash from the start. Automatic
car washes without brushes are prefera-
ble.

To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 506).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.
i
Vehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and
a SmartKey with KEYLESS-GO* is in close prox-
imity, i.e. within approximately 3 ft (approxi-
mately 1 m), the vehicle could be inadvertently
locked or unlocked.
!
Do not use scouring agents on these parts.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the vehicle.
Do not attempt to wipe the surface with a dry
cloth or sponge.
Otherwise you may scratch or damage the paint.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.
!
Make sure that the windshield wiper switch
is set to0 (
page 408). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent dam-
age to the mirrors.

688 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Auto Lamp Function
Inoperative
The light sensor is malfunctioning. Daytime
driving lamps are switched on.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
To switch off the headlamps (U.S. vehicles only):

Switch off daytime running lamps in the in-
strument cluster control system
(page 306).

Turn the exterior lamp switch to position0.
Check
Rear Left
Turn Signal
T h e l e f t r e a r t u r n s i g n a l l a m p i s m a l f u n c t i o n -
ing. A substitute bulb is being used.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Check
Rear Right
Turn Signal
The right rear turn signal lamp is malfunc-
tioning. A substitute bulb is being used.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Check
Left Mirror
Turn Signal
The turn signal in the left exterior rear view
mirror is malfunctioning. This message will
only appear if a critical number of light emit-
ting diodes have stopped working.

Have the LEDs replaced as soon as possible.

689 Practical hints
What to do if …?
Display
Possible cause/consequence
Possible solution
Check
Right Mirror
Turn Signal
The turn signal in the right exterior rear view
mirror is malfunctioning. This message will
only appear if a critical number of light emit-
ting diodes have stopped working.

Have the LEDs replaced as soon as possible.
Check
Front Left
Turn Signal
The left front turn signal lamp is malfunc-
tioning.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Check
Front Right
Turn Signal
The right front turn signal lamp is malfunc-
tioning.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Check
Left High Beam
The left high beam lamp is malfunctioning.

Replace the bulb as soon as possible
(page 714).
Check
Right High Beam
The right high beam lamp is malfunctioning.

Replace the bulb as soon as possible
(page 714).
Check Left
License Plate Lamp
The left license plate lamp is malfunction-
ing.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Check Right
License Plate Lamp
The right license plate lamp is malfunction-
ing.

Contact an authorized Mercedes-Benz Cen-
ter as soon as possible.
Please
Switch Off Lights
You are getting out of the vehicle and the
lights are still switched on.

Switch off the headlamps (
page 399).

716 Practical hintsReplacing bulbsNotes on bulb replacement


Only use 12-volt-bulbs of the same
type and with the specified watt rating.


Switch lights off before changing a bulb
to prevent short circuits.


Always use a clean lint-free cloth when
handling bulbs.


Your hands should be dry and free of oil
and grease.


If the newly installed bulb does not
come on, contact an authorized
Mercedes-Benz Center.
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Center:


the Bi-Xenon lamps


the front turn signal lamps


the front fog lamps


the additional turn signal lamps in the
exterior rear view mirrors


the parking and standing lamps


the front side marker lamps


the high mounted brake lamps


the brake, tail and rear standing lamps


the rear side marker lamps


the rear fog lamp


the rear turn signal lamps


the rear side marker lamps


the license plate lamps
Warning!
G
Bulbs and bulb sockets can be very hot. Al-
low the lamp to cool down before changing
a bulb.
Keep bulbs out of reach of children.
Halogen lamps contain pressurized gas. A
bulb can explode if you:

touch or move it when hot


drop the bulb


scratch the bulb
Wear eye and hand protection.
Because of high voltage in Xenon lamps, it is
dangerous to replace the bulb or repair the
lamp and its components. We recommend
that you have such work done by a qualified
technician.
!
Do not replace the LEDs yourself. You could
otherwise damage the LEDs or parts of the vehi-
cle. Only have the LEDs replaced by an autho-
rized Mercedes-Benz Center.
i
Have the headlamp adjustment checked
regularly.

720 Practical hintsReplacing bulbsAdditional turn signal lamp bulbs
The additional turn signal lamps in the ex-
terior rear view mirrors have LEDs.
If a malfunction occurs or LEDs fail to func-
tion, the entire turn signal unit must be re-
placed. Have the turn signal unit replaced
by an authorized Mercedes-Benz Center.
Front side marker lamp bulbs
Since replacing the side marker lamp bulbs
is a technically highly demanding process,
we recommend you have the side marker
lamp bulbs replaced by an authorized
Mercedes-Benz Center.

762 Technical dataMain dimensions and weightsMain dimensionsModel
S 450 4MATIC (221.184)
1
S 550 (221.171)
S 550 4MATIC (221.186)
S 600 (221.176)
S 63 AMG (221.077)
S 65 AMG (221.179)
1Canada onlyOverall vehicle length
205.0 in (5 210 mm)
Overall vehicle width (exterior rear view mirrors folded out)
83.2 in (2 115 mm)
Overall vehicle width (exterior rear view mirrors folded in)
73.7 in (1 928 mm)
Overall vehicle height
All models except S 63 AMG
58.46 in (1 485 mm)
S 63 AMG
58.0 in (1 473 mm)
Wheelbase
124.6 in (3 165 mm)
Track, front
63.2 in (1 600 mm)
Track, rear
63.3 in (1 606 mm)

775 Index
A
ABC* 470
Messages in display 660
Setting vehicle level 471
ABS 67
Indicator lamp 29, 67, 628
Messages in display 662
Accelerator position, automatic
transmission 433
Accessory weight 606
Accident 421
Active headlamps 399
Adaptive Brake Lights
(S 600, USA only) 69
Adaptive Damping System
(Airmatic) 468
Additional turn signals 715
Address book (COMAND) 167
Calling up 168
Changing an entry 174
Creating an entry 168
Deleting an entry 175
Details about an entry 172
Displaying details about an entry in
the phone book on the mobile
phone 173Importing data 179
Making a call 176
Menu overview 167
Searching for an entry 170
Starting route guidance 176
Voice entry 177
Address book (Voice Control) 330
ADS (Airmatic) 468
Advanced Parking Guidance* 481
Air bags 42
Children 58
Front 46
Front passenger front air bag
indicator lamp 51
OCS 47
Safety guidelines 44
Side impact 46
Window curtain 46, 47
Air conditioning, Refrigerant 768, 769
Air distribution
Adjusting 510
Adjusting (COMAND) 275
Air pressure 606
Air pressure see Tire inflation pressure
Air recirculation mode 506
Air vents 500Air volume
Adjusting 504, 510
Adjusting (COMAND) 275
Airmatic 468
Messages in display 676
Setting vehicle level 469
Alarm
Audible alarm and flashing exterior
lamps (Panic alarm) 66
Alarm system see Anti-theft alarm system
Alignment bolt (vehicle tool kit) 705, 726
Ambient lighting
COMAND menu 269
AMG menu (Control system
instrument cluster) 296
AMG vehicles
Manual shift program mode 440
Antiglare
Rear view mirrors 390
Anti-theft systems 82
Alarm, visual and audible 82
Anti-theft alarm system 82
Immobilizer 82
Aquaplaning see Hydroplaning
Armrest 527, 528
Ashtrays 536