reset MERCEDES-BENZ S-Class 2008 W221 Comand Manual

259 Control systems
COMAND system settings
COMAND system settings
System settings menu overviewDisplay settings
Switching the display on or off
Switching off: Select “Vehicle”

“Display OFF”.

Switching back on: Rotate ymz or
slideqmr.Setting the display design

Select “Vehicle”
“System Settings”

“Display”.

Select “Day Mode”, “Night Mode” or
“Automatic”.
Time settings
Setting the time
Select “Vehicle”
“System Settings”

“Time”
“Time”.

Selecting hour or minute(s):
Slideomp.
i
The components and operating principles of
COMAND can be found on (
page 87).
Display
(page 259)
Time
(page 259)
Voice Control
(page 261)
Language
(page 262)
Favorite
(page 263)
Reset
(page 259)
Display settings
Time settings
Voice Control set-
tings
Language settings
Assign favorite but-
ton
Reset COMAND to
factory settings
i
In the “Automatic” setting, COMAND ana-
lyzes the automatic vehicle light sensor and
switches between the display design automati-
cally.
i
The correct time must be set for the follow-
ing navigation system functions to operate cor-
rectly:


Route guidance on routes with time-depen-
dent traffic guidance


Calculation of estimated arrival time


263 Control systems
COMAND system settings
Assigning the favorite button
1Favorite button
You can assign the following predefined
functions to the favorite buttonP:

“Rear Window Sunshade” (
page 535)
You can use the favorite button to ex-
tend or retract the rear window sun-
shade. This is the default setting.


“Display OFF” (
page 259)
You can use the favorite button to
switch the COMAND display on or off.


“Repeat Navigation Command”
(page 243)You can use the favorite button to re-
call the last announcement issued by
the navigation system.

Select “Vehicle”
“System Settings”

“Favorite”.
The list of predefined functions appears.
The dot R in front of the list entry indi-
cates the current setting.

Changing setting: Rotate ymz and
select desired function.

Saving setting and exit the menu:
Press n.
Reset
Select “Vehicle”
“System Settings”

“Reset”.
A prompt appears asking whether you
really want to reset.

Select “Yes” or “No”.
If you select “Yes” another prompt will
appear asking whether you really want
to reset.

Select “Yes” or “No”.
If you select “Yes”, COMAND will be re-
set and restarted.
i
You can reset COMAND back to its factory
settings.
In this case, all personal data (e.g. address book
entries, entries in the destination memory and
the list of last destinations of the navigation sys-
tem), among other things, is deleted.

289 Control systems
Instrument cluster control system
Menus
Trip (
page 291)
Navi (
page 292)
Audio (
page 294)
AMG
1 (page 296)
1S63AMG and S65AMG only.Commands/submenusStandard display
Showing route guidance in-
structions, current direction
traveled
Selecting radio station
Gear currently engaged
Engine oil temperature
Vehicle supply voltage
Fuel consumption statistics since start
Selecting satellite radio
channel
RACETIMER
Fuel consumption statistics since last
reset
Operating DVD changer/
audio CD/ audio DVD/MP3
Overall analysis
Resetting fuel consumption statistics
Operating video DVD
Lap analysis
Distance to emptyDigital speedometer

291 Control systems
Instrument cluster control system
Trip menu
In the “Trip” menu, you can show an addi-
tional display for the speedometer and call
up or reset your vehicle’s statistical data.
Standard display
In the standard display, the trip odometer
and main odometer are shown in the mul-
tifunction display.
Press ( or & to select the “Trip”
menu.
1Main odometer
2Trip odometerFuel consumption statistics since start

Press ( or & to select the “Trip”
menu.

Press % to select “From Start”.
1Distance driven since start
2Time elapsed since start
3Average speed since start
4Average fuel consumption since startFuel consumption statistics since last
reset

Press ( or & to select the “Trip”
menu.

Press % or $ to select “Since
Reset”.
1Distance driven since last reset
2Time elapsed since last reset
3Average fuel consumption since last re-
set
4Average speed since last reset
i
The menu overview can be found on
(
page 289).
i
All values that are based on the last start are
reset when you turn off the vehicle’s engine for
more than four hours (
page 424).
i
If you turn the SmartKey to position1 or2
again during this time, the values will not be re-
set. After 9 999 hours or 99 999 miles (kilome-
ters), the fuel consumption statistics since start
are automatically reset.
i
After 9 999 hours or 99 999 miles (kilome-
ters), the fuel consumption statistics since last
reset are automatically reset.

292 Control systemsInstrument cluster control systemResetting fuel consumption statistics
Press ( or & to select the “Trip”
menu.

Press % or $ to select the func-
tion you wish to reset.

Press #.
Illustration: Reset trip odometer
Press % t o s e l e c t “Yes” and confirm
with #.Distance to empty

Press ( or & to select the “Trip”
menu.

Press % or $ to select “Range”.
The calculated remaining driving range
based on the current fuel tank level ap-
pears in the multifunction display.
Digital speedometer

Press ( or & to select the “Trip”
menu.

Press % or $ to select the digital
speedometer.
1Digital speedometer
Navi menu
The display in the “Navi” menu depends on
whether route guidance is active or not.
Press ( or & t o s e l e c t t h e “Navi”
menu.
Route guidance not active
The multifunction display shows the direc-
tion of travel and the name of the street
you are currently driving on, if known by
the navigation system.
1Direction of travel
2Street you are currently driving on
i
You can reset the trip odometer by pressing
and holding the
L
button. The trip odometer
is then reset without confirmation.
i
If only very little fuel is left in the tank, a fuel
pump is shown instead of the range.
i
The menu overview can be found on
(
page 289).

294 Control systemsInstrument cluster control system

“Calculating Route”
COMAND is calculating a route. After-
ward, COMAND starts route guidance.


“Off Map”
The vehicle’s location is outside of the
digital map’s range. The vehicle is in an
off-map position (
page 242).


“Off Mapped Road”
The vehicle is either on a road that has
not been digitized (
page 242) or on
the side of a road, e.g. in a parking
space.


“No Route”
COMAND cannot calculate a route to
the selected destination.


“Direction of Dest.”
The vehicle has gone off the map dur-
ing route guidance (
page 242).
Audio menu
The functions in the “Audio” menu operate
the audio equipment which you currently
have turned on.
If no audio equipment is currently turned
on, the message: “Audio OFF” is shown in
the multifunction display.
Selecting radio station
Turn on COMAND and select “Radio”
(page 102).

Press ( or & to select the “Au-
dio” menu.

Selecting a preset station: Briefly
press % or $.

Selecting a station using the search
function: Press and hold % or
$.1Station frequency
2Waveband

Press æ or ç to adjust the vol-
ume.
i
The menu overview can be found on
(
page 289).
i
You can only change the frequency band
and save new stations using COMAND
(
page 102).

298 Control systemsInstrument cluster control systemResetting current lap
Press buttonæ while the timer is
running.
The timer stops.

Press buttonç.
The lap time is reset to “0”.
Deleting all laps

Press buttonæ while the timer is
running.
The timer stops.

Press buttonç for at least
3 seconds.
The saved laps are deleted.

Press buttonæ to start timer again.
The saved laps are deleted.
or

Press #.The reset menu appears in the multi-
function display.

Press % to select “Yes” and confirm
with #.
The saved laps are deleted.

Press buttonæ to start timer again.Overall analysis

Press ( or & to select the
“AMG” menu.

Press $ repeatedly until the overall
analysis appears in the multifunction
display.
1Overall analysis of RACETIMER
2Overall driving time
3Maximum speed
4Overall distance driven
5Average speed

To select a different display, press
$, ( or &.
i
It is not possible to delete a single saved lap.
i
These functions are only available if you
have saved at least one lap and have stopped the
RACETIMER.

355 Control systems
Voice Control individualization
Voice Control individualization
The individualization is used to adapt the
Voice Control System to your own voice
and to therefore improve speech recogni-
tion. This does not affect the speech rec-
ognition of other users.
Individualization consists of two stages:

Digits


Commands
You can activate individualization in the
COMAND system settings (
page 261).
A dialog and screen displays will guide you
through the individualization process.
The system can be reset to the factory set-
tings at any time.
i
The individualization can only be performed
when the vehicle is stationary.
If you drive off, the individualization will be can-
celed.
After starting the session, the system will guide
you through the individualization by means of
acoustic instructions.
i
You may wish to complete only a portion of
the individualization process.
Completing the digits portion alone may result in
an improved recognition rate.
Individualization can be exited at any time. The
data trained, however, will only be retained if a
given individualization portion is completed and
the data is stored when prompted to do so by the
system.

368 Controls in detailLocking and unlockingPower closing assist for doors and trunk lid
It is not necessary to slam the door or
trunk lid closed. An electrical power-assist-
ed mechanism draws doors and trunk lid
closed quietly and automatically once door
and trunk lid has been latched. When the
electrical power-assisted mechanism has
stopped, doors and/or trunk can be
re-opened.

Power closing assist for doors: Press
the doors gently past the initial engage
position into the lock.
The doors close automatically.

Power closing assist for trunk lid:
Press the trunk lid gently into its lock.
The trunk closes automatically.For more information on closing the trunk
lid, see “Closing trunk” (
page 512).
Automatic central locking
The doors and the trunk automatically lock
when the ignition is switched on and the
wheels are turning at vehicle speeds of ap-
proximately 9 mph (15 km/h) or more. The
locking knobs in the doors move down.
You can open a locked door from the in-
side. Open door only when conditions are
safe to do so.
You can deactivate the automatic locking
using the COMAND system (
page 267).
Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
or trunk lid opening when closing a door or
the trunk. Be especially careful when small
children are around.
In case of danger, pull the inside or outside
door handle, or pull the trunk lid handle.
To prevent personal injury, never actuate
the closing assist mechanism by tampering
with the door or trunk lid latch.
Warning!
G
Only drive with the doors closed. Otherwise,
one or more of the doors could open while
the vehicle is in motion, putting you and/or
others at risk.Warning!
G
Only drive with the trunk closed as, among
other dangers such as blocked visibility, ex-
haust fumes may enter the vehicle interior.
These fumes may be damaging to your
health.
i
The doors are designed to unlock automati-
cally after an accident if the force of the impact
exceeds a preset threshold.
The vehicle locks automatically when the ignition
is switched on and the wheels are turning at ve-
hicle speeds of approximately 9 mph (15 km/h)
or more. You could therefore lock yourself out
when the vehicle


is pushed or towed


is on a test stand

403 Controls in detail
Lighting
Rear fog lamp (driver’s side only)
Turn the exterior lamp switch to
positionB (
page 399).

Pull out exterior lamp switch to second
stop.
The front fog lamps and the rear fog
lamp switch on.
The yellow indicator lamp† in the
exterior lamp switch comes on
(page 399).

Push in the exterior lamp switch to first
stop.
The rear fog lamp switches off.
The yellow indicator lamp† in the
exterior lamp switch goes out.
The front fog lamps remain lit.
High beamCombination switch1High beam
2High beam flasher
High beam headlamps: Turn the exte-
rior lamp switch to positionB
(page 399).

Push the combination switch in the di-
rection of arrow1.
The high beam indicatorA in the in-
strument cluster comes on
(page 28).

High beam flasher: Pull the combina-
tion switch briefly in the direction of
arrow2.
Headlamp cleaning system
With the engine running the headlamps will
automatically be cleaned with a high-pres-
sure water jet when you have

switched on the headlamps
and


the windshield wipers have wiped the
windshield with washer fluid five times
When you switch off the ignition the
counter resets.
For information on filling up the washer
reservoir, see “Windshield washer system
and headlamp cleaning system”
(
page 580).