trunk MERCEDES-BENZ S-Class 2008 W221 Comand Manual

365 Controls in detail
Locking and unlocking

Global locking: Close all doors and
touch outside of door handle1. Do
not keep your hand in the door handle
recess.
With the trunk and both doors closed:

All turn signal lamps flash three
times.


An acoustic signal sounds three
times (if equipped and feature acti-
vated).


The locking knobs in the doors
move down.


The anti-theft alarm system is
armed.Selective setting
If you frequently travel alone, you may wish
to reprogram the SmartKey with
KEYLESS-GO so when you, grasp the driv-
er’s outside door handle only the driver’s
door and the fuel filler flap unlocks.

Press and hold buttonsŒ and‹
simultaneously for about 5 seconds un-
til battery check lamp5 (
page 361)
flashes twice.
The SmartKey with KEYLESS-GO will
then function as follows:

Unlocking driver’s door and fuel fill-
er flap: Grasp the driver’s outside door
handle.


All turn signal lamps flash once.


An acoustic signal sounds once
(if equipped and feature activated).
For more information, see “Factory
setting” (
page 364).


The locking knob in the driver’s
door moves up.


The anti-theft alarm system is dis-
armed.

Global unlocking: Grasp any outside
door handle other than the driver’s out-
side door handle.

All turn signal lamps flash once.


An acoustic signal sounds once
(if equipped and feature activated).


The locking knobs in the doors
move up.


The anti-theft alarm system is dis-
armed.
i
Vehicles with trunk opening/closing
system*:
You can also lock the vehicle using the
KEYLESS-GO locking/closing switch
(
page 514).


366 Controls in detailLocking and unlocking
Global locking: Close all doors and
touch outside of door handle1
(page 364). Do not keep your hand in
the door handle recess.
With the trunk and both doors closed:


All turn signal lamps flash three
times.


An acoustic signal sounds three
times (if equipped and feature acti-
vated).


The locking knobs in the doors
move down.


The anti-theft alarm system is
armed.

Restoring to factory setting: Press
and hold buttonsŒ and‹ si-
multaneously for about 5 seconds until
battery check lamp5 (
page 361)
flashes twice.
Checking batteries in the SmartKey or
SmartKey with KEYLESS-GO*
Press button‹ orŒ.
The battery check lamp (
page 358)
or (
page 361) comes on briefly to in-
dicate that the SmartKey or SmartKey
with KEYLESS-GO batteries are in or-
der.Loss of the SmartKey or SmartKey with
KEYLESS-GO*
If you lose your SmartKey, SmartKey with
KEYLESS-GO or mechanical key, you
should do the following:
Have the SmartKey or SmartKey with
KEYLESS-GO deactivated by an autho-
rized Mercedes-Benz Center.

Report the loss of the SmartKey,
SmartKey with KEYLESS-GO or the me-
chanical key immediately to your car
insurance company.

Have the mechanical lock replaced if
necessary.
Any authorized Mercedes-Benz Center will
be glad to supply you with a replacement.
i
Vehicles with trunk opening/closing
system*:
You can also lock the vehicle using the
KEYLESS-GO locking/closing switch
(
page 514).
!
If the battery check lamp does not come on
briefly during check, the SmartKey or SmartKey
with KEYLESS-GO batteries are discharged.
Replace the batteries (
page 712).
You can obtain the required batteries at any au-
thorized Mercedes-Benz Center.
i
If the batteries are checked within signal
range of the vehicle, pressing button‹ or
Πwill lock or unlock the vehicle accordingly.


368 Controls in detailLocking and unlockingPower closing assist for doors and trunk lid
It is not necessary to slam the door or
trunk lid closed. An electrical power-assist-
ed mechanism draws doors and trunk lid
closed quietly and automatically once door
and trunk lid has been latched. When the
electrical power-assisted mechanism has
stopped, doors and/or trunk can be
re-opened.

Power closing assist for doors: Press
the doors gently past the initial engage
position into the lock.
The doors close automatically.

Power closing assist for trunk lid:
Press the trunk lid gently into its lock.
The trunk closes automatically.For more information on closing the trunk
lid, see “Closing trunk” (
page 512).
Automatic central locking
The doors and the trunk automatically lock
when the ignition is switched on and the
wheels are turning at vehicle speeds of ap-
proximately 9 mph (15 km/h) or more. The
locking knobs in the doors move down.
You can open a locked door from the in-
side. Open door only when conditions are
safe to do so.
You can deactivate the automatic locking
using the COMAND system (
page 267).
Warning!
G
To prevent possible personal injury, always
keep hands and fingers away from the door
or trunk lid opening when closing a door or
the trunk. Be especially careful when small
children are around.
In case of danger, pull the inside or outside
door handle, or pull the trunk lid handle.
To prevent personal injury, never actuate
the closing assist mechanism by tampering
with the door or trunk lid latch.
Warning!
G
Only drive with the doors closed. Otherwise,
one or more of the doors could open while
the vehicle is in motion, putting you and/or
others at risk.Warning!
G
Only drive with the trunk closed as, among
other dangers such as blocked visibility, ex-
haust fumes may enter the vehicle interior.
These fumes may be damaging to your
health.
i
The doors are designed to unlock automati-
cally after an accident if the force of the impact
exceeds a preset threshold.
The vehicle locks automatically when the ignition
is switched on and the wheels are turning at ve-
hicle speeds of approximately 9 mph (15 km/h)
or more. You could therefore lock yourself out
when the vehicle


is pushed or towed


is on a test stand

369 Controls in detail
Locking and unlocking
Locking and unlocking from the inside
You can lock or unlock the doors and the
trunk from the inside using the central
locking or unlocking switch. This can be
useful, for example, if you want to lock the
vehicle before starting to drive.
The central locking switch and central un-
locking switch do not lock or unlock the
fuel filler flap or the interior storage com-
partments such as the glove box.1Central unlocking switch
2Central locking switch

Locking: Press switch ‹.
If the front passenger door is closed,
the vehicle locks.

Unlocking: Press switch Œ.
The vehicle unlocks.
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. A child’s unsupervised ac-
cess to a vehicle could result in an accident
and/or serious personal injury.
i
You can open a locked door from inside at
any time. Open door only when conditions are
safe to do so.
If the vehicle was previously centrally locked
with the SmartKey or with KEYLESS-GO*, it will
not unlock using the central unlocking switch.
If the vehicle was previously locked with the cen-
tral locking switch:


and the SmartKey or SmartKey with
KEYLESS-GO* is set to factory settings, the
complete vehicle is unlocked when a door is
opened from the inside


and the SmartKey or SmartKey with
KEYLESS-GO* is set to selective settings,
only the door opened from the inside is un-
locked

407 Controls in detail
Lighting
The interior lighting switches off auto-
matically following an adjustable time
delay (
page 270).
Manual control

Switching on/off front interior light-
ing: Press button 3.

Switching on/off rear interior light-
ing: Press button 2.
The front reading lamps reading lamps are
located in the lower edge of the interior
rear view mirror.

Switching on/off front reading
lamps: Press button 1 or 5.

Ambient lighting: The brightness of
the ambient lighting is adjusted via
COMAND (
page 269).Interior lighting in the rear
1Rear interior lamp
2Button
3Reading lamp

Press button2.
You can switch the lamps on/off in
succession as follows:

reading lamp3 and rear interior
lamp1 on


only reading lamp3 on


reading lamp3 off
Door entry lamps
For better orientation in the dark, the cor-
responding door entry lamps will switch on
in darkness when you open a door and the
automatic control is activated.
The door entry lamps switch off when the
corresponding door is closed.Trunk lamp
The trunk lamp switches on if the trunk is
opened.
If the trunk remains open, the trunk light-
ing switches off automatically after ap-
proximately 10 minutes.
i
If the door remains open, the interior lighting
switches off automatically after approximately
5minutes.
i
If you turn the SmartKey in the starter
switch to position0 and switch off the exterior
headlamps, the door entry lamps will remain lit
for approximately 5 minutes.

423 Controls in detail
Driving and parking
1Handle for electronic parking brake
Manually releasing electronic parking
brake
Pull handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster goes out.
You cannot release the electronic parking
brake until the ignition is switched on.Automatically releasing electronic park-
ing brake
Your vehicle’s electronic parking brake is
automatically released when:


The engine is running.


Transmission is in drive positionD or
reverse gearR.


The hood is closed.


You have fastened your seat belt.


You step on the accelerator pedal.
If reverse gearR is engaged, the trunk
must be closed. Manually engaging electronic parking
brake

Press handle1.
The red indicator lamp 0 (USA only)
or ! (Canada only) in the instru-
ment cluster comes on.
i
If you have not fastened your seat belt, the
following conditions must be met in order for the
electronic parking brake to be automatically re-
leased:


The driver’s door is closed.


You must move the gear selector out of park
positionP position or drive faster than 2 mph
(3 km/h).
i
You can also engage the electronic parking
brake when the SmartKey is removed from the
starter switch.

424 Controls in detailDriving and parkingAutomatically engaging electronic park-
ing brake* (USA only)
Your vehicle’s electronic parking brake is
automatically engaged when DISTRONIC
Plus* (
page 451) brings your vehicle to a
standstill and at least one of the following
conditions is met:


The engine is switched off.


The driver’s door is opened and the
seat belt is not inserted in the seat belt
buckle.


The hood is released.


The trunk lid is open while reverse
gearR is engaged.


The vehicle is parked for an extended
period of time.
The red indicator lamp 0 (USA only) or
! (Canada only) in the instrument clus-
ter comes on.Emergency braking with electronic
parking brake
In an emergency situation, you can also
brake your vehicle while driving by using
the electronic parking brake.

While driving, press handle for elec-
tronic parking brake (
page 422).
During the braking procedure, the red indi-
cator lamp 0 (USA only) or !
(Canada only) flashes in the instrument
cluster, the message “Please Release Park-
ing Brake” appears on the multifunction
display and you will hear a warning tone.
Once the vehicle comes to a complete stop
the electronic parking brake will engage.
Turning off the engine 
Shift the automatic transmission toP
(page 430).
i
In addition to the electronic parking brake,
park position P can be automatically engaged.
i
Your vehicle will be braked for as long as you
press and hold the switch for the electronic park-
ing brake. The longer you keep the electronic
parking brake pressed, the more strongly your
vehicle will be braked. This method occurs on all
4 wheels, not just the rear wheels.
i
If the engine cannot be turned off as de-
scribed, see “Emergency engine shut-down”
(
page 744).Warning!
G
Do not turn off the engine before the vehicle
has come to a complete stop. With the en-
gine not running, there is no power assis-
tance for the brake and steering systems. In
this case, it is important to keep in mind that
a considerably higher degree of effort is nec-
essary to brake and steer the vehicle.!
Observe instructions


when taking the vehicle through an
automatic conveyor type car wash
(page 618)


when towing the vehicle (
page 737)

431 Controls in detail
Automatic transmission
!
DISTRONIC Plus*:
The transmission will shift to park positionP
automatically, only when DISTRONIC Plus brings
your vehicle to a standstill, and when it meets at
least one of the following conditions at the same
time:


The engine is turned off.


The driver’s or passenger door opens and
the seat belt is not engaged in the buckle.


The hood is released.


The trunk lid is open while reverse gearR is
engaged.


The vehicle is parked for an extended period
of time.
In addition to shifting to park positionP, the
electronic parking brake will be engaged auto-
matically.
i
Make it a practice to always shift into park
positionP before turning off the engine and


remove the SmartKey from the starter
switch
or


open a front door
or when using KEYLESS-GO*, before turning off
the engine with the start/stop button and open-
ing a front door.
Effect
í
Reverse gear
Shift into reverse gearR only
when the vehicle is stopped.
ë
Neutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never shift into neutral
positionN while driving.
If the ESP
® is deactivated or
malfunctioning:
Shift into neutral positionN only
if the vehicle is in danger of
skidding, e.g. on icy roads.
Effect

487 Controls in detail
Driving systems
Canceling the Advanced Parking
Guidance
Press the Park Assist* button
(page 480).
The Advanced Parking Guidance is im-
mediately canceled and Park Assist* is
deactivated. No message is shown in
the multifunction display.
The Advanced Parking Guidance is auto-
matically canceled if guidance into the
parking space is no longer possible or if an
error occurs.
The parking space symbol disappears and
the message “Parking Guidance Canceled”
appears in the multifunction display.
Rear View Camera*
T he R e a r V i e w C a m e r a i s a n e l e c t r o n i c a n d
visual parking aid. It shows you the area
behind the vehicle on the COMAND dis-
play.
In addition, the Rear View Camera contains
guide lines to help you with driving in re-
verse.
The area behind the vehicle is displayed as
a reverse-mirror image similar to the view
in a rear-view mirror.The Rear View Camera is in the handle
strip of the trunk lid.
1Rear View Camera

489 Controls in detail
Driving systems
Switching on Rear View Camera
Switch on the ignition (
page 370).

Switch on COMAND (
page 87).

Move gear selector lever to reverse
gearR.
The COMAND display will show the
area behind the vehicle with guide
lines.
Warning!
G
Make sure no persons or animals are in the
area in which you are maneuvering. You
could otherwise injure them.Warning!
G
The Rear View Camera may not function if:

the trunk lid is not completely closed


it is raining or snowing heavily, or if
there is thick fog


in a very dark area


the camera is exposed to very strong
white light (white stripes may appear on
the COMAND display)


the surrounding area is lit with fluores-
cent light (the COMAND display can
flicker)


outside temperatures are very high (lens
condensation)


there is a sudden change in tempera-
ture, for example when you drive out of
the cold into a heated garage in winter
(lens condensation)


the camera lens is dirty or covered, see
“Cleaning the Rear View Camera* lens”
(page 621)


the rear of your vehicle is damaged. In
this case, have the position and setting
of the camera checked by a qualified
technician. Contact an authorized
Mercedes-Benz Center.
Do not use the Rear View Camera if the
roads are icy, slippery or covered with snow.
The vehicle could slip causing the actual ve-
hicle position to deviate from the one shown
on the COMAND display.
This may cause injury to you or others, or
damage the vehicle or objects.
Mounting tires/rims of other specification
than the original equipment tires/rims may
impair the function of the Rear View Cam-
era. Contact an authorized Mercedes-Benz
Center.
Warning!
G
Use of Rear View Camera can be dangerous
if you are color-blind or have impaired color
vision.
Only use Rear View Camera if you can see
and distinguish all colored guide lines shown
by Rear View Camera on the COMAND dis-
play.i
The Rear View Camera must be activated in
the instrument cluster control system in order
for it to be switched on (
page 303).