remote control MERCEDES-BENZ S350 2006 W221 User Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2006, Model line: S350, Model: MERCEDES-BENZ S350 2006 W221Pages: 481
Page 114 of 481
113 Controls in detail
Locking and unlocking
Locking and unlocking from the inside
You can lock or unlock the doors and the
trunk from inside using the central locking
or unlocking switch. This can be useful, for
example, if you want to lock the vehicle be-
fore starting to drive.
The fuel filler flap will not be locked or un-
locked with the central locking or unlock-
ing switch, respectively.The switches are located on the upper part
of the front center console.
1Central locking switch
2Central unlocking switch
Locking
Press central locking switch1.
If the front passenger door is closed,
the vehicle locks.
Unlocking
Press central unlocking switch2.
The vehicle unlocks.
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
iYou can open a locked door from the
inside. Open door only when conditions
are safe to do so.
If the vehicle was previously centrally
locked with the SmartKey or the with
KEYLESS-GO*, it will not unlock using
the central unlocking switch2.
If the vehicle was previously locked
with the central locking switch1:
While in the global remote control
mode, the vehicle is unlocked com-
pletely when a door is opened from
the inside.
While in the selective remote con-
trol mode, only the door opened
from inside is unlocked.
Page 255 of 481
254 Controls in detailUseful featuresTele Aid
The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:
automatic and manual emergency
roadside assistance, and
informationThe Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the volume knob
on your COMAND head unit.
To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.
!The initial activation of the Tele Aid sys-
tem may only be performed by com-
pleting the subscriber agreement and
placing an acquaintance call using the
Information button¡. Failure to
complete either of these steps will re-
sult in a system that is not activated.
If you have any questions regarding ac-
tivation, please call the Response Cen-
ter at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.
iThe Tele Aid system utilizes the cellular
network for communication and the
GPS (Global Positioning System) satel-
lites for vehicle location. If either of
these signals are unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.
Page 262 of 481
261 Controls in detail
Useful features
Remote door unlock
In case you have locked your vehicle unin-
tentionally (e.g. SmartKey inside vehicle),
and the reserve SmartKey is not handy:
Contact the Mercedes-Benz Response
Center at 1-800-756-9018 (in the USA)
or 1-888-923-8367 (in Canada).
You will be asked to provide your pass-
word which you provided when you
completed the subscriber agreement.
Then return to your vehicle and press
the trunk lid button for a minimum of
20 seconds until the SOS button is
flashing.
The message:
CALL CONNECTED
ap-
pears in the multifunction display.
As an alternative, you may unlock the vehi-
cle via Internet using the ID and password
sent to you shortly after the completion of
your acquaintance call.
The Response Center will then unlock your
vehicle with the remote door unlocking
feature.
iWhen a Tele Aid call has been initiated,
the audio system or the COMAND*
system audio is muted and the
selected mode (radio or CD) pauses.
The optional cellular phone (if installed)
switches off. If you must use this
phone, the vehicle must be parked.
Disconnect the coiled cord and place
the call. The COMAND* navigation
system (if engaged) will continue to
run. The display in the instrument
cluster is available for use, and spoken
commands are only available by press-
ing the RPT button on the COMAND*
unit. A pop-up window will appear in
the COMAND* display to indicate that
a Tele Aid call is in progress.
iThe remote door unlock feature is avail-
able if the relevant cellular phone net-
work is available.
The SOS button will flash and the mes-
sage:
CALL CONNECTED
will appear in
the multifunction display to indicate re-
ceipt of the door unlock command.
Once the vehicle is unlocked, a Re-
sponse Center specialist will attempt
to establish voice contact with the ve-
hicle occupants.
If the trunk lid button was pressed for
more than 20 seconds before door un-
lock authorization was received by the
Response Center, you must wait
15 minutes before pressing the trunk
lid button again.
Page 264 of 481
263 Controls in detail
Useful features
Garage door opener
The built-in remote control is capable of
operating up to three separately controlled
devices, for example garage door openers,
gate openers, or other devices compatible
with HomeLink
® or some other systems.
You can program the signal transmitter
buttons.
Remote control integrated into the interior
rear view mirror1Indicator lamp
2 3 4Signal transmitter button
5Hand-held transmitter button
6Hand-held remote control trans-
mitter (not part of the vehicle
equipment)
Warning!
G
Before programming the integrated remote
control to a garage door opener or gate op-
erator, make sure people and objects are
out of the way of the device to prevent po-
tential harm or damage.
When programming a garage door opener,
the door moves up or down. When program-
ming a gate operator, the gate opens or
closes.
Do not use the integrated remote control
with any garage door opener that lacks safe-
ty stop and reverse features as required by
U.S. federal safety standards (this includes
any garage door opener model manufac-
tured before April 1, 1982). A garage door
that cannot detect an object - signaling the
door to stop and reverse - does not meet
current U.S. federal safety standards.
Page 266 of 481
265 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on the ignition (
page 34).
Step 2:
If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and 4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:
Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to 12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:
Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:
When the indicator lamp 1 flashes
rapidly, release both buttons.
Step 6:
Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
Page 268 of 481
267 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:
To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:
Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.
Proceed with programming step 5 and
step 6 to complete.
Page 269 of 481
268 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 34).
Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory
Switch on the ignition (
page 34).
Simultaneously hold down the signal
transmitter buttons 2and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 flashes rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated sig-
nal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.
The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the integrated signal transmitter
button, proceed with programming
starting with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.
Page 459 of 481
458 IndexDriving
Abroad 281
General instructions 43, 273
Hydroplaning 277
In winter 279
Problems 54
Safety systems 79
Through standing water 280
With Distronic* 227
Driving abroad 281
Driving instructions 273
Driving off 276
Driving safety systems
4MATIC 84
ABS 79
BAS 80
ESP
®
81
Driving systems 215
ABC 232
AIRMATIC 229
Airmatic 229
Cruise control 215
Distronic* 218
Driving safety systems 79
Parktronic system* 235
Vehicle level control 230, 233E
Easy-entry/exit feature 114
Activating 170
Electrical fuses 416
Electrical system 432
Electronic Stability Program see
ESP
®
81, 445
Emergency call system 254
Emergency calls
Initiating an emergency call 256
With Tele Aid 255
Emergency operation (Limp Home
Mode) 185
Emergency operations
Closing the power tilt/sliding
sunroof 391
Locking the vehicle 389
Opening the power tilt/sliding
sunroof 391
Remote door unlock 261
Unlocking the vehicle 388
Emergency tensioning device see
ETD 69, 445
Emission control 282
Emission control information label 422Ending
A call (telephone) 154
Engine
Cleaning 334
Compartment 287
Data 424
Message in display 342, 343
Starting 46
Starting with KEYLESS-GO* 47
Starting with the SmartKey 46
Turning off with the SmartKey or the
SmartKey with KEYLESS-GO* 57
Engine compartment 287
Fuse box in 418
Hood 287
Engine malfunction indicator lamp 342,
343
Engine number 422, 445
Engine oil 288
Adding 292
Additives 437
Checking level 288
Consumption 288
Display messages 366
Filler neck 291, 292, 293
Messages in display 290, 366
Page 461 of 481
460 IndexFuel tank
Filler flap 284
Fuels, coolants, lubricants etc. 434
Functions (control system) 145, 147
Resetting 161
Fuse box 417, 418
Fuse chart 385
Fuses 416
Auxiliary fuse box in trunk 417
F us e box i n engi ne c om p art me nt 4 18
Fuse box in passenger
compartment 417
Fuse chart 385
Fuse extractor 385
Spare fuses 385
G
Garage door opener 263
Erasing in remote control 268
Integrated remote control 265
Rolling code programming 266
Gasoline see Fuel 285
GAWR 323
Gear range 445
Automatic transmission 178
Limiting 178
Shifting into optimal 180Gear range limit
Canceling 180
Gear selector lever
Cleaning 337
Position (Automatic
transmission) 175
Glasses
Storage compartment in front of
armrest 245
Global
Locking 94
Unlocking 94
Global Positioning System (GPS) 446
Glove box 242
Closing 243
Locking 242
Opening 243
Unlocking 243
Gloves (vehicle tool kit) 385
Good visibility 186
GPS 254, 446
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GVW 323
GVWR 324H
Hand-held transmitter
Programming integrated remote
control 265
Hands-free microphone 29
Hard plastic trim items
Cleaning 337
Hazard warning flasher 136
Switching off 136
Switching on 136
Head restraints 116
Headlamp cleaning system* 296
Headlamps
Automatic control 132
Bi-Xenon 444
Cleaning 334
Cleaning system* 186, 296
Refilling washer fluid 296
Switching off 57
Switching on 50
Headliner
Cleaning 337
Heated steering wheel* 252
Height adjustment
Head restraints 39
Steering wheel 40
Page 462 of 481
461 Index
Height adjustments
Vehicle level 230, 233
High beam 50
Replacing bulbs 395
High beam flasher 135
High beam headlamps
Messages in display 370
Switching on 135
High mounted brake lamp 395
High-performance brake system
(S 65 AMG only) 275
Hood 287
Closing 288
Message in display 368
Opening 287
Hydroplaning 277
I
Identification labels 422
Emission control information
label 422
Vacuum line routing diagram
label 422
Ignition 34, 36
Switching on 34, 46, 47Immobilizer 85
Activating 85
Deactivating 85
Indicator lamps see Lamps, indicator and
warning
Individual seats* 117
Head restraint height 118
Infant and child restraint systems 71
Installing 74
LATCH child seat anchors 75
Information
About service and warranty 10
Button for Tele Aid 259
Infrared reflecting windshield 269
Inside rear view mirror
Auto-dimming 186
Installing
Infant and child restraint systems 74
Towing eye bolt 415
Wiper blades 402
Instrument cluster 24, 140, 446
Cleaning 337
Coolant temperature gauge 141
Illumination 140Multifunction display 143
Outside temperature indicator 142
Selecting language 164
Integrated remote control
Canadian programming 267
Erasing memory 268
Hand-held transmitter 265
Operating 268
Rolling code programming 266
Interior illumination
Delayed switch-off 167
Interior lighting 137
Activating automatic control 137
Deactivating automatic control 137
Manual operation 137
Reading lamps in the front 138
Reading lamps in the rear 138
Interior rear view mirror
Adjusting 41
J
Jump starting 411