clock MERCEDES-BENZ S430 2004 W220 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2004, Model line: S430, Model: MERCEDES-BENZ S430 2004 W220Pages: 435, PDF Size: 3.83 MB
Page 22 of 435
21 At a glance
Cockpit
Item
Page
1
Combination switch
Turn signals
Windshield wipers
High beam
47
48
128
2
Cruise control lever
Cruise control
Distronic*
210
203
206
3
Instrument cluster
22
4
Multifunction steering
wheel
24
5
Gear range indicator, clock
22
6
Lever for voice control sys-
tem*, see separate operat-
ing instructions
Item
Page
7
Front Parktronic* (Parking
assist) warning indicator
for right front area
226
8
Overhead control panel
27
9
Glove box lock
231
a
Glove box lid release
231
b
Glove box
231
c
Center console
25
d
Starter switch
31
e
Horn
f
Steering wheel adjustment
stalk
Heated steering wheel*
37
240
Item
Page
g
Parking brake pedal
45
h
Hood lock release
272
j
Parking brake release
45
k
Door control panel
28
l
Exterior lamp switch
124
m
Headlamp washer button*
177
n
Front Parktronic* (Parking
assist) warning indicator
for left front area
226
Page 24 of 435
23 At a glance
Instrument cluster
Item
Page
1
Coolant temperature gauge
132
2
Fuel gauge with:Fuel reserve warning lamp
308
3
LLeft turn signal
indicator lamp
47
KRight turn signal
indicator lamp
4
Speedometer with:vESP warning lamp
308
lDistance warning
lamp
Vehicles without Distronic*:
Warning lamp without func-
tion. It illuminates when the
ignition is on. It should go
out when the engine is run-
ning.
307
5
Tachometer
133
6
Right display with:
Item
Page
AHigh beam headlamp
indicator
48
-Antilock Brake Sys-
tem (ABS) warning
lamp
304
7
Reset button
131
8
Display with:
Program mode
170
Gear range indicator
166
Digital clock (see
COMAND operating in-
structions)
9
Multifunction display
with:
Trip odometer
132
Main odometer
132
Stored speed for:
Cruise control
203
Distronic*
206
Item
Page
a
Outside temperature indica-
tor
133
b
Left display with:1Supplemental
restraint system
indicator lamp
310
;Brake warning lamp,
USA only
305
3Brake warning lamp,
Canada only?Engine malfunction
indicator lamp, USA
only
306
±Engine malfunction
indicator lamp,
Canada onlyHTire pressure warning
lamp
287,
309
c
Knob for instrument cluster
illumination
131
Page 106 of 435
105 Controls in detail
Locking and unlocking
Separately locking the trunk lidThe lock is located next to the recessed
handle.
1Locked
2Neutral position
Close the trunk lid (
page 98).
Pull the mechanical key out of the
SmartKey (
page 348).
Insert the mechanical key into the
trunk lid lock.
Turn the mechanical key clockwise to
position1.
The trunk remains locked even when the
vehicle is centrally unlocked.
Separately unlocking the trunk lid
Pull the mechanical key out of the
SmartKey (
page 348).
Insert the mechanical key into the
trunk lid lock.
Turn the mechanical key counterclock-
wise to neutral position2, see above.
You can now open the trunk (
page 97).
A minimum height clearance of 6 ft.
(1.85 m) is required to open the trunk lid.
iYour vehicle may be equipped with a
function permitting the separate lock-
ing of the trunk using the mechanical
key. If present, this feature can permit
you to deny any unauthorized person
access to the trunk by locking the trunk
separately and leaving the SmartKey
less the mechanical key with the
vehicle.
To verify the presence of this feature,
use the mechanical key to lock the
trunk and then attempt to open the
trunk by pressing the trunk lid button
after the vehicle has been centrally
unlocked with the SmartKey.
iYou can only cancel the separate trunk
locking mode by means of the
mechanical key.Warning!
G
Only drive with the trunk closed as, among
other dangers such as visibility blockage,
exhaust fumes may enter the vehicle
interior.
Page 132 of 435
131 Controls in detail
Instrument cluster
Instrument cluster
A full view illustration of the instrument
cluster can be found in the “At a glance”
section of this manual (
page 22).
The instrument cluster is activated when
you:
open a door
turn on the ignition
press the reset button (
page 22)
switch on the exterior lamps
You can change the instrument cluster set-
tings in the instrument cluster submenu of
the control system (
page 154).
Instrument cluster illumination
1Knob for adjusting instrument cluster
illumination
Use knob1 to adjust the illumination
brightness for the instrument cluster.
Press knob1.
The knob will pop out.
To brighten illumination
Turn knob1 in the instrument cluster
clockwise.
The instrument cluster illumination will
brighten.
To dim illumination
Turn knob1 in the instrument cluster
counterclockwise.
The instrument cluster illumination will
dim.
iThe instrument cluster illumination is
dimmed or brightened automatically to
suit ambient light conditions.
The instrument cluster illumination will
also be adjusted automatically when
you switch on the vehicle’s exterior
lamps.
Page 346 of 435
345 Practical hints
Where will I find ...?
The vehicle tool kit includes:
One interchangeable slot/Phillips
screwdriver
One towing eye bolt
One wheel bolt wrench with socket
wrench
One alignment bolt
One pair of gloves
One fuse extractor
One fuse chart for the main fuse box
Spare fusesVehicle jack
To prepare the vehicle jack for use
Remove the vehicle jack from the spare
wheel well under the trunk floor.
Push the crank handle up.
Turn the crank handle clockwise until it
engages (operational position).Storing the vehicle jack in the trunk
Retract the vehicle jack arm to the
base of the vehicle jack.
Push the crank handle up.
Turn the crank handle counterclock-
wise to the end of the stop (storage po-
sition).
!To prevent damage, always disengage
trunk floor handle from trunk lid and
lower trunk floor before closing the
trunk lid.
Page 347 of 435
346 Practical hintsWhere will I find ...?
Spare wheel
Removing the spare wheel
Take out the vehicle tool kit tray2.
Loosen the luggage bowl3. To do so,
turn the luggage bowl counterclock-
wise
Remove the spare wheel4.
Storing the spare wheel
Place spare wheel4in wheel well.
Secure the spare wheel. To do so, turn
the luggage bowl3 clockwise to its
stop.
Place vehicle tool kit tray2 in luggage
bowl.Spare wheel S 430, S 500 and S 600
(except Sport Package*)
The spare wheel rim is mounted with a full
sized tire of the same type as on the vehi-
cle, and it is fully functional.
However, that spare wheel rim is weight
optimized and has a limited service life of
12 000 miles (20 000 km) use before a
standard wheel rim must replace it.
In case of flat tire, you may temporarily use
the spare wheel.
Do not operate vehicle with more than one
spare wheel mounted.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure the jack arm is
fully seated in the jack take-up bracket. Al-
ways lower the vehicle onto sufficient ca-
pacity jackstands before working under the
vehicle.
Page 350 of 435
349 Practical hints
Unlocking/locking in an emergency
Unlocking the trunk
A minimum height clearance of 6 ft.
(1.85 m) is required to open the trunk lid.
If you are unable to unlock the trunk with
the SmartKey or KEYLESS-GO*, open the
trunk with the mechanical key.
The trunk lid lock is located above the rear
license plate recess.
1Unlocking and opening
Insert the mechanical key into the
trunk lid lock.
Turn the mechanical key counterclock-
wise to position1.
The trunk unlocks and opens.
Locking the vehicle
If you are unable to lock the vehicle with
the SmartKey or the SmartKey with
KEYLESS-GO*, lock it with the mechanical
key as follows:
Close the passenger doors and the
trunk lid.
Press the central locking switch in the
center console (
page 107).
Check to see whether the locking knob
on the passenger door is still visible. If
necessary push it down manually.
Slide mechanical key2 out of the
SmartKey (
page 348).
Lock the driver’s door with the me-
chanical key (
page 348).
Lock the trunk lid if necessary with the
mechanical key (if applicable)
(page 105).
Replacing batteries in the SmartKey/
SmartKey with KEYLESS-GO*
If the batteries in the SmartKey or the
SmartKey with KEYLESS-GO* are dis-
charged, the vehicle can no longer be
locked or unlocked. It is recommended to
have the batteries replaced at an autho-
rized Mercedes-Benz Center.
!The trunk lid swings open upwards au-
tomatically. Always make sure that
there is sufficient overhead clearance.
Warning!
G
Keep the batteries out of reach of children.
If a battery is swallowed, seek medical help
immediately.
Page 353 of 435
352 Practical hintsOpening/closing in an emergency
Opening/closing in an emergencySliding/pop-up roof
You can open or close the sliding/pop-up
roof manually should an electrical malfunc-
tion occur.
The driving mechanism for the slid-
ing/pop-up roof is located behind the lens
of the interior overhead light.
1Lens
Pry off lens1 using a flat blade srew-
driver (
page 344).
Turn the SmartKey in the starter switch
to position1 or2.
Remove the crank from the operator’s
manual pouch.
2Crank
Insert crank2 through hole.
Turn crank2 clockwise to:
close slide roof
raise roof at the rear
Turn crank2 counterclockwise to:
open slide roof
lower roof at the rear
The sliding/pop-up roof must be resyn-
chronized after being operated manually
(
page 202).
Page 357 of 435
356 Practical hintsReplacing bulbs
Insert the new bulb in the socket so
that the base is in the recess on the
lower left.
Attach the retaining springs.
Insert connector7 into the bulb.
Press cover3 onto the housing until
the tab engages.Replacing halogen high beam bulbs
Switch off the lights.
Open the hood (
page 272).
Press the tab on cover2 and remove
cover.
Pull connector 6 off of the bulb.
Apply pressure on the bulb contacts
from above until the bulb releases from
the retaining springs.
Remove bulb.
Insert the new bulb in the socket with
the marking facing upward.
Press the bulb upward on the contacts
until it engages in the retaining springs.
Insert connector6 onto the bulb.
Press cover2 onto the housing until
the tab engages.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 272).
Twist bulb socket8 counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall bulb socket in lamp and twist
clockwise until it engages.
Page 358 of 435
357 Practical hints
Replacing bulbs
Parking and standing lamp bulb
Switch off the lights.
Open the hood (
page 272).
Press the tab on cover2 and remove
cover.
Pull out the bulb socket5 with the
bulb.
Pull the bulb out of the bulb socket.
Insert a new bulb in the socket.
Reinstall the bulb socket.
Press cover2 onto the housing until
the tab engages.Side marker lamp bulb
Switch off the lights.
Carefully slide lamp towards rear.
Remove front end first.
Twist bulb socket counterclockwise
and pull out.
Pull bulb out of the bulb socket.
Insert new bulb in socket.
Reinstall bulb socket, push in and twist
clockwise.
To reinstall lamp, set rear end in
bumper and let front end snap into
place.