Program MERCEDES-BENZ S500 2006 W221 Owner's Guide

264 Controls in detailUseful features
iCertain types of garage door openers
are incompatible with the integrated
opener. If you should experience diffi-
culties with programming the transmit-
ter, contact an authorized
Mercedes-Benz Center, or call
Mercedes-Benz Customer Assistance
Center (in the USA) at
1-800-FOR-MERCedes, or Customer
Service (in Canada) at
1-800-387-0100.
iUSA only:
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.
iCanada only:
This device complies with RSS-210 of
Industry Canada. Operation is subject
to the following two conditions:
(1) This device may not cause interfer-
ence, and
(2) this device must accept any inter-
ference received, including interfer-
ence that may cause undesired
operation of the device.
Any unauthorized modification to this
device could void the user’s authority
to operate the equipment.

265 Controls in detail
Useful features
Programming or reprogramming the in-
tegrated remote control
Step 1:
Switch on the ignition (
page 34).
Step 2:

If you have previously programmed an
integrated signal transmitter button
and wish to retain its programming,
proceed to step 3. Otherwise, press
and hold the two outer signal transmit-
ter buttons2 and 4 and release
them only when the indicator lamp1
begins to flash after approximately
20 seconds (do not hold the button for
longer than 30 seconds). This proce-
dure erases any previous settings for
all three channels and initializes the
memory. If you later wish to program a
second and/or third hand-held trans-
mitter to the remaining two signal
transmitter buttons, do not repeat this
step and begin directly with step 3.Step 3:

Hold the end of the hand-held remote
control transmitter6 of the device
you wish to train approximately 2 to
5 in (5 to 12 cm) away from the surface
of the integrated remote control locat-
ed on the interior rear view mirror,
keeping the indicator lamp1 in view.
Step 4:

Using both hands, simultaneously
press the hand-held transmitter
button5 and the desired integrated
signal transmitter button (2, 3
or4). Do not release the buttons until
completing step 5.
The indicator lamp1 on the integrat-
ed remote control will flash, first slowly
and then rapidly.Step 5:

When the indicator lamp 1 flashes
rapidly, release both buttons.
Step 6:

Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp1.
If the indicator lamp1 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.iThe indicator lamp1 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.


266 Controls in detailUseful featuresStep 7:
To program the remaining two buttons,
repeat the steps above starting with
step 3.Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:

Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn” or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual. Step 9:

Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:

Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (2, 3
or4).
Step 11:

Press, hold for two seconds and re-
lease same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.
iIf the indicator lamp1 flashes rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code feature”.


267 Controls in detail
Useful features
Step 12:
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (2, 3
or4).
Step 13:

To program the remaining two buttons,
repeat the steps above starting with
step 3.Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:Step 4:

Continue to press and hold the inte-
grated signal transmitter button (2,
3 or4) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter6 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp1 will flash slowly and
then rapidly after several seconds.

Proceed with programming step 5 and
step 6 to complete.

268 Controls in detailUseful featuresOperation of integrated remote control
Switch on the ignition (
page 34).

Select and press the appropriate inte-
grated signal transmitter button (2,
3 or4) to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.Erasing the integrated remote control
memory

Switch on the ignition (
page 34).

Simultaneously hold down the signal
transmitter buttons 2and 4, for ap-
proximately 20 seconds, until the indi-
cator lamp1 flashes rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.Reprogramming a single integrated sig-
nal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:

Press and hold the desired signal trans-
mitter button (2, 3 or4). Do not re-
lease the button.

The indicator lamp1 will begin to
flash after 20 seconds. Without releas-
ing the integrated signal transmitter
button, proceed with programming
starting with step 3.
iIf you sell your vehicle, erase the codes
of all three channels.

272 OperationIn the “Operation” section you will find de-
tailed information on operating, maintain-
ing and caring for your vehicle.The first 1000 miles (1500 km)
The more cautiously you treat your vehicle
during the break-in period, the more satis-
fied you will be with its performance later
on.

Drive your vehicle during the first
1 000 miles (1 500 km) at varying but
moderate vehicle and engine speeds.


During this period, avoid heavy loads
(full throttle driving) and excessive en-
gine speeds (no more than
2/3 of max-
imum rpm in each gear).


Avoid accelerating by kick-down.


Do not attempt to slow the vehicle
down by shifting to a lower gear using
the gear selector lever.


Select positions3,2or1 only when
driving at moderate speeds (for hill
driving).


Select C as the preferred shift program
(page 179) for the first 1000 miles
(1500 km).After 1 000 miles (1 500 km) you may grad-
ually increase vehicle and engine speeds
to the permissible maximum.
All of the above instructions, as may apply
to your vehicle type, also apply when driv-
ing the first 1 000 miles (1 500 km) after
the engine or the rear differential has been
replaced.
!Additional instructions for AMG vehi-
cles:

During the first 1 000 miles
(1 500 km), do not exceed a speed
of 85 mph (140 km/h).


During this period, avoid engine
speeds above 4500 rpm
(S 55 AMG) or 4000 rpm
(S 65 AMG) in each gear.
iAlways obey applicable speed limits.

448 Technical termsProgram mode selector switch
Used to switch the automatic transmis-
sion between standard operationS and
comfort operationC.
S55 AMG and S65 AMG with steering
wheel gearshift control and manual
shift program: in addition toS andC
(see above), you can useM for manual
operation.
PSI
(P
ounds per s
quare i
nch)
(
page 324)
Recommended tire inflation pressure
(page 324)
REST
(Residual engine heat utilization)
Feature that uses the engine heat
stored in the coolant to heat the vehi-
cle interior for a short time after the en-
gine has been turned off.Restraint systems
Seat belts, belt tensioners, air bags
and child restraint systems. As inde-
pendent systems, their protective func-
tions complement one another.
Rim
(
page 324)
RON
(Research O
ctane N
umber)
The Research Octane Number for gaso-
line as determined by a standardized
method. It is an indication of a gaso-
line’s ability to resist undesired detona-
tion (knocking). The average of both
the ->MON (Motor Octane Number)
and RON (Research Octane Number) is
posted at the pump, also known as AN-
TI-KNOCK INDEX.
Shift lock
When the vehicle is parked, this lock
prevents the transmission selector le-
ver from being inadvertently moved out
of positionP without the SmartKey
turned and the brake pedal depressed.Sidewall
(
page 324)
SRS
(Supplemental R
estraint S
ystem)
Seat belts, emergency tensioning de-
vice and air bags. Though independent
systems, they are closely interfaced to
provide effective occupant protection.
Tele Aid System
(T
elematic A
larm I
dentification on
D
emand)
The Tele Aid system consists of three
types of response: automatic and man-
ual emergency, Roadside Assistance
and information. Tele Aid is initially ac-
tivated by completing a subscriber
agreement and placing an acquain-
tance call.
The Tele Aid system is operational pro-
vided that the vehicle’s battery is
charged, properly connected, not dam-
aged and cellular and GPS coverage is
available.

451 Index
A
ABC 232, 443
Messages in display 351
Setting vehicle level 230, 233
ABS 25, 79, 443
Malfunction indicator lamp 340
Messages in display 353
Warning lamp 340
Accelerator position, automatic
transmission 177
Accessory weight 323
Accident
In case of 54
Activating
Air conditioner (cooling) 202
Air conditioning 202
Air recirculation mode 198
Anti-theft alarm system 86
Central locking (control system) 168
Charcoal filter 200
Distance warning function* 227
Distronic* 223
Easy-entry/exit feature 170
ESP
®
83
Exterior lamps 132
Exterior rear view mirror parking position 187
Front and rear fog lamp 132, 134
Hazard warning flasher 136
Headlamps 50
High beams 135
Ignition 34
Ignition with KEYLESS-GO* start/stop
button 36
Immobilizer 57, 85
Limiting opening height of trunk
lid* 169
Manual shift program S 55 AMG and
S 65 AMG 184
Rear window defroster 201
Residual heat 202, 207
Seat heater 125, 126
Seat ventilation* 127
Tow-away alarm 88
Windshield wipers 52
Adaptive Damping System (ADS) 229,
443
Adding
Coolant 294
Engine oil 292
Additional turn signals 395
Adjustable air vents, rear passenger compartment 204
Adjusting 37
Air distribution 196, 206
Air volume 197
Backrest tilt 38
Drive-dynamic seat* 171
Exterior rear view mirrors 41
Head restraint height 39
Head restraint tilt 39
Instrument cluster illumination 140
Interior rear view mirror 41
Lumbar support 122
Mirrors 41
Multicontour backrest* 122
Power seat bench* 117
Seat cushion depth 38, 123
Seat cushion tilt 38
Seat fore and aft adjustment 38
Seat height 38
Seat in the lumbar region 123
Seat in the shoulder region 123
Seats 37
Steering column height 40
Steering column in or out 40
Steering column up or down 40
Steering wheel 40

453 Index
Automatic headlamp mode 132
Automatic lighting control
Activating 137
Deactivating 137
Automatic locking when driving 112
Automatic shift program
Automatic transmission 179
Automatic transmission 173
Accelerator position 177
Automatic shift program 179
Emergency operation (Limp Home
Mode) 185
Fluid level 293
Gear ranges 178
Gear selector lever position 173, 175
Gear shifting malfunctions 185
Kickdown 177
Kickdown, manual shift program
S 55 AMG and S 65 AMG 185
Manual shift program S 55 AMG and
S 65 AMG 183
Manual shifting 180
One-touch gearshifting 180
Selector lever position 173
Starting the engine 46Steering wheel gearshift control
S 55 AMG and S 65 AMG 181
Transmission fluid 293
Auxiliary fuse box 417
B
BabySmart
TM
Air bag deactivation system 73
Compatible child seats 73, 443
Self-test 73
BabySmart
TM air bag deactivation
system 443
Backrest supports
Lumbar region 123
Shoulder region 123
Backup lamps 395, 400
Bulbs 395
Bar 323
BAS 80, 444
Batteries, SmartKey
Check lamp 95
Checking 95
Replacing 392
Batteries, SmartKey with KEYLESS-GO*
Checking 101
Battery discharged
Jump starting 411Battery, SmartKey with KEYLESS-GO*
Check lamp 101
Replacing 393
Battery, vehicle 295, 408
Charging 409
Disconnecting 409
Reconnecting 410
Reinstalling 409
Removing 409
Bead 323
Bi-Xenon headlamps 444
Block heater (Canada only) 328
Blocking
Rear window operation 77
Brake assist system (BAS) 444
Brake fluid 285, 437
Brake lamp bulbs 395
Brake lamp, high mounted 395
Brake pads
Message in display 361
Brakes 274
High-performance brake system
(S 65 AMG only) 275
Warning lamp 341
Break-in period 272

456 IndexConvenience submenu 169
Activating easy-entry/exit
feature 170
Adjusting drive-dynamic seat* 171
Setting key-dependency 169
Setting parking position for exterior
rear view mirror 170, 172
Coolant 294
Adding 294
Checking level 294
Messages in display 362, 363
Temperature 283
Temperature gauge 141
Warning lamp 363
Coolant level
Checking 294
Coolant temperature gauge 25
Courtesy lighting 139
Cruise control 215, 444
Canceling 216
Driving downhill 216
Driving uphill 216
Fine adjustment 217
Lever 222
Setting current speed 216Setting to last stored speed (“Resume”
function) 217
Cruise control lever 215
Cup holder
Cleaning 337
Closing 249
In front seat armrest 248
In rear seat armrest 249
Opening 249
Curb weight 323, 444
Customer Assistance Center (CAC) 444
D
Daytime running lamp mode 133
Setting 165
Deactivating
Air conditioner (cooling) 202
Air recirculation mode 199
Alarm 87
Anti-theft alarm system 87
Automatic climate control 195, 206
Central locking (control system) 168
Charcoal filter 200
Defrost 197
Distance warning function* 227Distronic* 225
Engine with the SmartKey 57
ESP
®
82
Exterior lamps 132
Hazard warning flasher 136
Headlamps 57
Immobilizer 85
Interior illumination delayed
switch-off 167
Limiting opening height of trunk
lid* 169
Manual shift program S 55 AMG and
S 65 AMG 185
Rear window defroster 201
Residual heat 203, 207
Seat heater 125, 126
Seat ventilation* 127
Tow-away alarm 88
Deceleration
With Distronic* 221
Deep water see Standing water 280
Defrosting 197
Delayed switch-off
Interior illumination 167
Department of Transportation see DOT