Service F MERCEDES-BENZ S550 2007 W221 Owner's Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: S550, Model: MERCEDES-BENZ S550 2007 W221Pages: 705
Page 104 of 705
103 Control systems
COMAND satellite radio* (USA only)
Saving a channel to a selected preset
position
If you have called up the channel preset
screen using option 1:
Press n briefly.
In options 2 and 3:
Press and hold n until you hear a sig-
nal.
The channel is saved.
Show program info
Select “Audio” “Audio” “Sat Ra-
dio” “Info”.
You will see a screen that may contain the
following information:
Selected program category
Selected channel
Artist of the track currently being
played
Name of current track
Closing screen: Slide omp or
pressn.
Channel update
The service provider may conduct a chan-
nel update.
During the update, the message “Updating
channels...” will appear on the display.
No functions can be operated in satellite
radio mode during the update.
Calling Sirius Service Center
Select “Audio” “Audio” “Sat Ra-
dio” “Sat Radio” “Service”.
The telephone number of the Sirius
Service Center and the twelve-digit
electronic serial number (SIRIUS-ID) of
the particular receiver are displayed.
Closing screen: Slide omp or
pressn.
i
If the program provider does not offer any in-
formation, the “Info” menu item cannot be se-
lected.
i
The program provider determines what in-
formation is displayed on the screen. COMAND
shows no more than two lines per item of infor-
mation. If an item of information is too long,
COMAND shortens it.
i
It may be necessary to call the Sirius Service
Center if, for example:
You want to cancel the subscription or
re-subscribe at a later date
You forget to pay the bill
You sell the car to another person
Page 117 of 705
116 Control systemsCOMAND telephone*Unless otherwise indicated, the descrip-
tions and illustrations in this section refer
to COMAND and the telephone keypad.
Operation using the mobile phone and
Bluetooth headset is described in the re-
spective separate Operating Instructions.
Caller ID
COMAND can display the telephone num-
ber and the name of the caller, e.g. for an
incoming call and also in other menus or
displays.
For the telephone number to be displayed,
the caller must transmit their telephone
number.
This is also the case for name displays. For
this, the telephone number and the name
of the caller must also be saved in the mo-
bile phone book.Functional restrictions
You will not be able to use the telephone,
or you may have to wait a while, in the fol-
lowing situations:
If the telephone has not yet logged into
the network.
The telephone automatically tries to
log into a network. If no network is
available, you will also not be able to
make a “911” emergency call.
If you attempt to make an outgoing call,
the “No Service” message will appear
for a short while.
If the mobile phone is not inserted in
the cradle.
SIM card is not inserted in GSM type
phone
Switching telephone on or off
Switching on: insert mobile phone
into cradle when COMAND is switched
on.
or
Switch on the mobile phone
(see mobile phone operating instruc-
tions).
Switching off: Select “Telephone”
“Telephone” “Telephone OFF”.
or
Switch off mobile phone (see mobile
phone operating instructions).
Page 118 of 705
117 Control systems
COMAND telephone*
Activating telephone mode
Select “Telephone” “Telephone”
“Telephone”.
or
Press s on telephone keypad.
Telephone keypad
1Telephone keypad
2Folding coverWith the telephone keypad you can:
Enter and clear numbers and special
characters
Reject, accept, connect and end calls
Entering characters: Select “Tele-
phone” “Telephone” “Telephone”.
Fold up cover 2.
Enter characters using A- #.
Deleting individual characters:
Press*.
Deleting an entire word or number:
Press and hold * until the word or
number is deleted.
“911” emergency call
The following conditions must be fulfilled
in order to make a “911” emergency call:
The phone is switched on
A mobile network is available
There is a valid SIM card in the phone
(not necessary in all mobile networks)
If you cannot make an emergency call, you
must initiate rescue measures yourself.
The “911” emergency call is a public ser-
vice. Any misuse is punishable by law.
i
You can enter the * character by
pressing> once. Pressing this button again
within 1.5 seconds enters the + character.
Warning!
G
The “911” emergency call system is a public
service. Using it without due cause is a crim-
inal offense.i
This function places a call to the local 911
provider. It does not initiate a Tele Aid call.
i
If no SIM card is inserted in the mobile
phone, you can only initiate a “911” emergency
call by using COMAND and the mobile phone.
Page 122 of 705
121 Control systems
COMAND telephone*
Main telephone menu
Calling up main menu: Select “Tele-
phone” “Telephone” “Telephone”.
or
Press s on the telephone keypad
(page 117).
Mailbox
The symbol in the example illustration
above indicates that your mailbox contains
new voice messages. You will have to call
the mailbox in order to retrieve the mes-
sages.
You can call your mailbox by:
Speed dialing (
page 126)
Entering a telephone number using the
telephone keypad (
page 125)
Entering the telephone number using
the COMAND controller (
page 125)
i
If you press s when the main telephone
menu has already been called up, the “Calls Di-
aled” list will appear (
page 122).
1Numbers / characters to enter tele-
phone number
2Symbol for new voice message in
mailbox
3Symbol for unread SMS messag-
es in SMS inbox (
page 137)
4Signal strength and network status
display
Network status “READY” = mobile
phone is logged in with its own
provider’s network
Network status “READY ROAM” =
mobile phone is logged in with an-
other provider’s network
Network status “No Service” = No
network available
5To show COMAND phone book
(“Name”) (
page 129)
6To call up text message (SMS)
(
page 137)
7To display call list selection
(page 122)
i
Once connection with your mailbox has
been established, the mailbox system will guide
you through the next steps.
Page 138 of 705
137 Control systems
COMAND telephone*
SMS messages (Short Message Service)
SMS functions
The following functions are available:
Receive
Read
The following conditions must be fulfilled
in order to use the functions:
The mobile phone is inserted in the cra-
dle and switched on
The PIN has been entered (only GSM
mobile phones)
The mobile phone is logged into a mo-
bile network
Mobile phone phone book must be
downloaded and available in COMANDInbox
Calling up the SMS inbox
Select “Telephone” “Telephone”.
The main telephone menu appears.
1Symbol for unread messages in the
SMS inbox
Select “Text Message”.
The SMS inbox appears.1Date and time the highlighted SMS
message was received
2To call up options
3Highlighted SMS message
4Symbol for unread SMS message
5Back to main telephone menu
i
The symbol only appears for those mes-
sages which are received while the mobile phone
is inserted in the cradle.
i
“Text Message” does not function if the
SMS inbox contains no SMS messages. The SMS
inbox only shows the messages which are re-
ceived while the mobile phone is inserted in the
cradle.
Page 214 of 705
213 Control systems
COMAND system settings
COMAND system settings
Systems settings menu overviewDisplay settings
Switching the display on or off
Switching off: Select “Vehicle”
“Display OFF”.
Switching back on: Rotate ymz or
slideqmr.
Setting the display design
Select “Vehicle” “System Settings”
“Display”.
Select “Day Mode” or “Night Mode” or
“Automatic”.
Time settings
Setting the time
Select “Vehicle” “System Settings”
“Time” “Time”.
Selecting hour or minute(s):
Slideomp.
Setting value: Rotate ymz or
slideqmr.
Saving setting: Press n.
i
The components and operating principles of
COMAND can be found on (
page 79).
Display
(page 213)
Time
(page 213)
Voice Control*
(page 215)
Language
(page 216)
Favorite
(page 216)
Services
(page 217)
Reset
(page 213)
Display settings
Time settings
Voice Control*
settings
Language
settings
Assign favorite
button
Bluetooth
settings
Reset COMAND to
factory settings
i
In the “Automatic” setting, COMAND ana-
lyzes the automatic vehicle light sensor and
switches between the display design automati-
cally.
i
The correct time must be set for the follow-
ing navigation system functions to operate cor-
rectly:
Route guidance on routes with time-depen-
dent traffic guidance
Calculation of estimated arrival time
i
The increment value for setting the minutes
depends on the situation. If GPS reception is
available, it is 30 minutes. If GPS reception is not
available, it is one minute.
Page 218 of 705
217 Control systems
COMAND system settings
Changing setting: Rotate ymz and
select desired function.
Saving setting and exit the menu:
Press n.
Bluetooth settings
General information about Bluetooth
Bluetooth technology is the standard for
short-range wireless data transmission of
up to approximately 10 meters. Bluetooth
can be used to exchange vCards or make
calls using a headset.
Activate or deactivate Bluetooth
Select “Vehicle” “System Settings”
“Services” “Deactivate Blue-
tooth”.
You have activated or deactivated Blue-
tooth. A checkmark appears when
Bluetooth is deactivated.Connecting Bluetooth devices
It is possible to establish a Bluetooth con-
nection between COMAND and the follow-
ing types of device:
Mobile phone (only for transferring
business cards)
Headset
Laptop / PDA
You can connect up to twelve devices to
COMAND but only one device can be ac-
tive at a time.
The connection process includes search-
ing for the device and its subsequent au-
thorization.Calling up the Bluetooth device list and
searching for devices
Calling up the list: Select “Vehicle”
“System Settings” “Services”
“Search for Bluetooth devices”.
When you call up the list for the first
time after switching on COMAND, the
search for devices in the reception
range starts automatically. You will see
a display to this effect.
The device list appears after a short
while.
Canceling search:
Select “Cancel”.
The second time you call up the list, and
each time thereafter, the device list ap-
pears immediately if COMAND has not
been switched off and on again in the
meantime.
Starting search manually:
select “Update”.
i
To connect a Bluetooth device, the Blue-
tooth function must be activated in COMAND
and in the device concerned. The Bluetooth de-
vice must also be set to “visible” or “findable” in
order for COMAND to find and display it. For the
setting procedures, please see the operating in-
structions for the Bluetooth device.
Page 242 of 705
241 Control systems
Instrument cluster control system
Instrument cluster control system
The control system is activated as soon as
the SmartKey in the starter switch is
turned to position2 or as soon as the
KEYLESS-GO* start/stop button
(page 317) is in position2. The control
system enables you to:
call up information about your vehicle
change vehicle settings
For example, you can use the control sys-
tem to find out when your vehicle is next
due for service, to call up statistical data
on your vehicle, and much more.
The control system relays information to
the multifunction display.
Multifunction display
1Line for main menus
2Text field in multifunction display
Settings, functions, submenus as well as
any malfunctions are shown to you in the
text field.
Warning!
G
A driver’s attention to the road and traffic
conditions must always be his/her primary
focus when driving.
For your safety and the safety of others, se-
lecting features through the multifunction
steering wheel should only be done by the
driver when traffic and road conditions per-
mit it to be done safely.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
Page 245 of 705
244 Control systemsInstrument cluster control system
Assistance* (
page 252)
Service (
page 253)
Settings (
page 254)
Commands/submenusDisplaying the distance graphic*
(DISTRONIC Plus*)
Call up vehicle malfunction, warning
and system status messages stored in
memory
Set daytime running lamp mode (USA only)
Distance warning function*
activating/deactivating
Check tire inflation pressure
Switch additional speedometer on or off
Switch on the Dynamic Rear View Moni-
tor* automatically
Call up maintenance service display
Switch radar sensors* on or off
Check engine oil level*
i
The headings used in the menus table are
designed to facilitate navigation within the sys-
tem and are not necessarily identical to those
shown in the control system displays. The first function displayed in each menu will au-
tomatically show you which part of the system
you are in.
Page 251 of 705
250 Control systemsInstrument cluster control systemYou can use the functions in the “Tele-
phone” menu to operate your telephone,
provided it is inserted in the cradle and
switched on.
Logging-on to a network
Switch on the telephone and COMAND
(page 79).
Press ( or & to select the “Tele-
phone” menu.Which messages appear in the multifunc-
tion display field depends on whether your
telephone is switched on or off.
If the telephone is off, the message in
the multifunction display is: “Telephone
OFF”.
If the telephone is not inserted in the
cradle, the message in the multifunc-
tion display is: “No telephone inserted”.
If the PIN or unlock code is not yet en-
tered, the message in the multifunction
display is “Please enter PIN” or “Enter
unlock code”.
If the telephone is switched on, the
telephone will then search for a net-
work. During this time, the multifunc-
tion display is blank. If no network
available, the multifunction display
reads “No Service”.
If the telephone is on, as soon as the
telephone has found a network,
“Ready” or “Ready (Roaming)” appears
in the multifunction display.Entering the PIN or unlock code
Enter the PIN or unlock code using the
telephone keypad*, Voice Control* or
telephone*.
The telephone will then search for a
network.
You may carry out the following functions:
Dialing a number from the mobile
phone book
If your telephone is ready to receive calls,
you may select and dial a number from the
phone book at any time.
Log on to the network (
page 250).
Warning!
G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and/or
personal injury.
Function
Page
Dialing a number from the phone
book
250
Redialing
251
Answering a call
252
Ending a call or rejecting an in-
coming call
252