warning MERCEDES-BENZ S550 2007 W221 Service Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: S550, Model: MERCEDES-BENZ S550 2007 W221Pages: 705
Page 142 of 705
141 Control systems
COMAND navigation (introduction)
Updating the map software
You can update the map software yourself
using a DVD.
Notes about handling DVDs
Only hold discs by the edge.
Handle discs carefully to prevent read
problems.
Avoid getting scratches, fingerprints
and dust on discs.
Use a commercially-available cleaning
cloth to clean discs. Do not wipe them
with a circular motion, but only in
straight lines from the center out-
wards.
Place discs back in their boxes after
use.
Protect discs from heat and direct sun-
light.
Updating process
The updating process has the following
phases:
Loading a DVD into the DVD changer
(page 142)
Updating process (
page 142)
i
The updating process can take between 10
and 60 minutes, depending on the size of the
map software. If the radio was switched on be-
fore you started the updating process, you can
still adjust the volume. You can also use
COMAND to operate the automatic air condition-
ing and to cancel the process. Other functions
are not operational.
If possible, carry out the update when the vehicle
is stationary.
i
If you carry out the update with the engine
switched off and the vehicle battery has insuffi-
cient power, COMAND may automatically switch
off during the process in order to protect the bat-
tery. If this occurs, restart the update with the
engine running period. Similarly, if the SmartKey
position is unintentionally switched to 0, restart
the update.Warning!
G
Never leave the engine running in an en-
closed space. The exhaust gases contain
carbon monoxide. Inhaling exhaust gases
constitutes a health hazard and could lead
to loss of consciousness or even death.
Page 154 of 705
153 Control systems
COMAND navigation system (entering a destination)
COMAND navigation system (entering a destination)
The following destination entry options are
available:
Entering a destination by address
Entering a destination from the desti-
nation memory
Entering a destination from the list of
last destinations
Entering a destination from the map
Entering a stopover
Entering a POI
Entering a destination by address
To enter an address you may proceed as
follows:
Enter state (USA) or province (CDN),
street and town/city
Enter state (USA) or province (CDN),
town/city and street
Enter state (USA) or province (CDN),
town/city and center
Enter state (USA) or province (CDN),
zip code and center
Enter state (USA) or province (CDN),
zip code and streetCalling up the address input menu
Select “Navi” “Destination” “Ad-
dress Entry”.
The address input menu appears. It
shows a state (USA) or a province
(CDN). Which state or province is
shown depends on the vehicle’s loca-
tion.
1State (USA) or province (CDN)
Warning!
G
For safety reasons, only enter a new desti-
nation when the vehicle is stationary.i
It is possible to enter a destination regard-
less of whether route guidance is active or inac-
tive.
i
It is not possible to enter an address when
the vehicle has exceeded a certain speed. As
soon as the vehicle speed drops below a certain
value, the function is available again.
i
If Russian or Chinese is set as the system
language, the address must be entered using
Latin letters. Setting the system language
(
page 216).
i
As additional information to the street entry,
you can enter either a house number or an inter-
section.
A zip code entry replaces the town/city entry.
Page 186 of 705
185 Control systems
COMAND navigation system (route guidance)
COMAND navigation system (route guidance)
Route guidance
COMAND guides you to the destination us-
ing navigation commands in the form of
audible navigation announcements and
route guidance displays.
If, for any reason, you do not follow the
navigation commands or if you leave the
calculated route, COMAND automatically
calculates a new route to the destination.
If the map data contains the relevant infor-
mation, COMAND tries to avoid roads that
only have limited access, e.g. roads closed
to through-traffic and non-residents.Roads that have time restrictions (e.g.
closed on Sundays and public holidays) are
not considered for route guidance, if the
digital map contains the relevant informa-
tion.
Examples of displays and announce-
ments for a driving maneuver
Driving maneuvers have three phases:
Preparation phase
Announcement phase
Maneuver phase
Warning!
G
COMAND calculates the route to the desti-
nation without taking account of the follow-
ing, for example:
Traffic lights
Stop and right-of-way signs
Parking or stopping prohibited areas
Lane merges
Other road and traffic rules and regula-
tions
Narrow bridges
COMAND may give incorrect navigation
commands if the data in the digital map
does not correspond with the actual
road/traffic situation. For example, if the
traffic routing has been changed or the di-
rection of a one-way road has been re-
versed.
For this reason, you must always observe
applicable road and traffic rules and regula-
tions during your journey. Road and traffic
rules and regulations always have priority
over the navigation commands generated by
the system.i
The route guidance displays can only be
seen if the display is switched to navigation
mode.
Page 189 of 705
188 Control systemsCOMAND navigation system (route guidance)Partially digitized areas If the destination is within a partially
digitized area
COMAND guides you through fully digitized
areas for as long as possible. Route guid-
ance is conducted in the usual manner, i.e.
with navigation announcements and route
guidance displays.
Before the vehicle reaches a partially digi-
tized area, COMAND notifies you of this
with the following announcements:
“Be prepared to enter an area where
turn by turn guidance cannot be provid-
ed.”
“In 700 feet you will enter an area
where turn by turn guidance cannot be
provided.”
“You are about to enter an area where
turn by turn guidance cannot be provid-
ed.”Route guidance within a partially digi-
tized area
If you start route guidance in this type of
area, you will hear the following announce-
ment: “You are currently in an area where
turn by turn guidance cannot be provided.”
Route guidance is provided by means of a
direction arrow showing the compass
heading to the destination. COMAND will
not generate automatic navigation an-
nouncements.
If you try to call up an announcement man-
ually, (
page 191) you will hear the an-
nouncement “You are currently in an area
where turn by turn guidance cannot be pro-
vided.”.
i
The digital map may contain areas that are
only partially digitized although they are within a
digitized region.Warning!
G
Due to incomplete digitization, the route
shown on the map may differ from the actual
road/traffic situation.
If you follow the route shown on the map, for
example, it is possible that you could drive
the wrong way down a one-way street or
that a street cannot be driven on.
When using route guidance in a partially dig-
itized area, you must therefore be sure to
observe all relevant traffic regulations and
the course of the road.
All relevant traffic regulations and the
course of the road always take priority over
the route shown on the map.
i
The indicated distance can be seen here by
way of example. In reality, it may be different.
i
When you call up the route info to this type
of destination, (
page 193) the following data
shown there may differ from the actual situation:
Distance to the destination
Estimated driving time to the destination
Estimated arrival time
Page 190 of 705
189 Control systems
COMAND navigation system (route guidance)
During route guidance, the display is divid-
ed. On the right-hand side you will see the
direction arrow showing the compass
heading to the destination.
On the left-hand side of the display you will
see the map with the suggested route. The
suggested route is highlighted blue. How-
ever, it may not be possible to follow the
suggested route because, for example, the
road is closed or not open for car traffic.
If, during route guidance, COMAND leads
you back into a fully digitalized area, route
guidance will simply continue in the usual
manner.
Off-road and off-map
Route guidance to an off-road destina-
tion
COMAND can guide you to destinations
within the area covered by the digital map,
even if a destination is not located at a
road known to the system.These destinations are shown as off-road
destinations, which you can enter using
the map, for example.
In these cases, COMAND guides you for as
long as possible with navigation announce-
ments and displays on roads known to the
system.
Shortly before you reach the last known
the point to leave the digitized road net-
work, you will hear the announcement “The
destination is nearby. Follow the arrow on
the display”.
You will then see an arrow that indicates
the direction to the off-road destination.
When the off-road destination is close to
the road, “Area of dest. reached” appears
in addition below the arrow.
The section of the route from the last
known point on the map to the off-road
destination is indicated with a dashed line
after a certain length. It simply shows the
direction to the off-road destination with-
out taking account of any type of obstacles
in the way.Warning!
G
The COMAND navigation system may direct
you to off-road routes that your vehicle may
not be capable of traversing through without
damaging your tires, wheels or vehicle. It is
the driver’s sole responsibility to determine
the suitability of the route. Off-road routes
may be of varying conditions and their ap-
propriateness for use may be affected by
various factors such as time of day, time of
year and immediate weather conditions that
cannot be judged or taken into consider-
ation by the COMAND system.
Page 192 of 705
191 Control systems
COMAND navigation system (route guidance)
Navigation announcements
Route guidance is already active.
Calling up a current announcement:
Select “Navi” 6.
or
Press P favorite button if the button
has been programmed with this func-
tion.
Canceling navigation message:
Briefly press F shortcut button dur-
ing an announcement.
Switching off navigation messages:
Press and hold F during an an-
nouncement until the announcement is
switched off.
You will see the message “The driving
instructions have been muted.” for a
short while.
Switching navigation announce-
ments back on manually:
Select “Navi” 6.
Adjusting volume of the messages:
adjust the volume during an automatic
announcement (
page 89).
or
Call up an announcement manually us-
ing “Navi” 6 and adjust the vol-
ume (
page 89).
Warning!
G
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.i
If Russian or Chinese is set as the system
language, the navigation announcements are in
English. You will find how to set the system lan-
guage on (
page 216).
Navigation announcements are muted during
telephone calls. You can, however, call up a cur-
rent announcement at any time. You can also
call up a current announcement at any time if
you have missed an announcement.
i
You will find the button programming on
(
page 216).
i
The announcements remain switched off
even if you start a new route guidance or if
COMAND is switched off/on with theo but-
ton.
If you switch COMAND off by removing the
SmartKey from the starter switch and then
switch the ignition back on after more than
3 minutes, the announcements are automatical-
ly switched back on.
Page 225 of 705
224 Control systemsCOMAND vehicle menuActivating easy-entry/exit feature
Use this function to activate and deacti-
vate the easy-entry/exit feature
(page 328).
The following settings are available for the
easy-entry/exit feature:
Select “Vehicle”.
The main area is active.
Selecting “Easy Entry/Exit Feature”
menu: Slide omp or rotate ymz.
Confirming selection: Press n.
or
Select “Vehicle” “Vehicle” “Easy
Entry/Exit Feature”.
Confirming selection: Press n.
A selection list appears.
The current setting is indicated by a
dotR.
i
The components and operating principles of
COMAND can be found on (
page 79).
OFF
The easy-entry/exit
feature is deactivated.
Steering Column
& Seat
Both the steering col-
umn and the driver’s
seat are moved.
Warning!
G
You must make sure no one can become
trapped or injured by the moving steering
wheel and driver’s seat when the easy-en-
try/exit feature is activated.
To cancel seat/steering wheel movement,
do one of the following:
Press seat adjustment switch
(page 319).
Move steering column stalk
(page 330).
Press one of the memory position but-
tons or the memory button M
(page 337).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
Page 230 of 705
229 Control systems
COMAND automatic climate control
COMAND automatic climate control
You can operate the automatic climate
control via COMAND or via the buttons on
the front and rear* automatic climate con-
trol panel (
page 424).
The following automatic climate control
functions can be operated via COMAND:The automatic climate control menu is
called up via the climate control settings.
Climate control settings with functions
(submenus)1Temperature, left
2Air distribution, left
3Air volume, left
4Central menu, climate control
5Air volume, right
6Air distribution, right
7Temperature, right
i
The components and operating principles of
COMAND can be found on (
page 79).
Warning!
G
When operating the automatic climate con-
trol, the air that enters the passenger com-
partment through the air vents can be very
hot or very cold (depending on the set tem-
perature). This may cause burns or frostbite
to unprotected skin in the immediate area of
the air vents.
Always keep sufficient distance between un-
protected parts of the body and the air
vents. If necessary, use the air distribution
adjustment (
page 230) to direct the air to
air vents in the vehicle interior that are not
in the immediate area of unprotected skin.
Warning!
G
Follow the recommended settings for heat-
ing and cooling given on the following pages
and pages in the “Controls in detail” part
(page 424) Otherwise the windows could
fog up, impairing visibility and endangering
you and others.
Function
Page
Temperature
230
Air distribution
230
Air volume
230
Switching off cooling (“AC
OFF”)
231
Central climate control (“Mono”)
232
Footwell temperature
232
Air flow from air vents
233
Rear climate control*
234
Page 232 of 705
231 Control systems
COMAND automatic climate control
Changing air volume: Slide qmr or
rotate ymz.
Exiting menu: Press n, back
buttonL in the center console
(page 80) or slideomp.
The setting is saved.
Central climate control menu via
COMAND
The central climate control menu is in the
center of the climate control settings.
When the automatic climate control is
switched on, you will see “on” in the cen-tral menu. The following functions can only
be operated in the central climate control
menu via COMAND:
Select climate control settings Cen-
tral menu.Switching cooling on or off
The cooling function, only operational
when the engine is running, cools the vehi-
cle interior down to the selected tempera-
ture. The cooling function also
dehumidifies the air in the vehicle interior,
thus preventing the windows from fogging
up.
The “AC
OFF” function is used to permanent-
ly switch off the cooling function of the au-
tomatic climate control system.
Function
Page
Switching off cooling (“AC
OFF”)
231
Central climate control (“Mono”)
232
Footwell temperature
232
Air flow from air vents
233
Rear climate control
234
i
Condensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.Warning!
G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and
others.
Page 242 of 705
241 Control systems
Instrument cluster control system
Instrument cluster control system
The control system is activated as soon as
the SmartKey in the starter switch is
turned to position2 or as soon as the
KEYLESS-GO* start/stop button
(page 317) is in position2. The control
system enables you to:
call up information about your vehicle
change vehicle settings
For example, you can use the control sys-
tem to find out when your vehicle is next
due for service, to call up statistical data
on your vehicle, and much more.
The control system relays information to
the multifunction display.
Multifunction display
1Line for main menus
2Text field in multifunction display
Settings, functions, submenus as well as
any malfunctions are shown to you in the
text field.
Warning!
G
A driver’s attention to the road and traffic
conditions must always be his/her primary
focus when driving.
For your safety and the safety of others, se-
lecting features through the multifunction
steering wheel should only be done by the
driver when traffic and road conditions per-
mit it to be done safely.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.