Jump start MERCEDES-BENZ S550 2007 W221 Owner's Manual

Contents
Practical hints................................. 543
What to do if …?................................. 544
Lamps in instrument cluster ........ 544
Air bag off indicator lamp ............. 555
Vehicle status messages in the
multifunction display .................... 557
Where will I find ...? ........................... 611
First aid kit ................................... 611
Vehicle jack, vehicle tool kit,
luggage bowl, Minispare wheel .... 611
Unlocking/locking in an emergency .. 614
Unlocking the vehicle ................... 614
Locking the vehicle ...................... 615
Mechanically releasing the
electric parking brake .................. 616
Opening/closing in an emergency..... 617
Power tilt/sliding sunroof or
panorama roof with power
tilt/sliding panel* ........................ 617Resetting activated head restraints
(S 600 only) ........................................ 618
Replacing SmartKey batteries ............ 619
SmartKey/SmartKey with
KEYLESS-GO* ............................... 619
Replacing bulbs .................................. 621
Bulbs ............................................. 622
Replacing bulbs for front lamps .... 623
Replacing wiper blades....................... 627
Placing wiper arms in vertical
position ......................................... 627
Removing wiper blades ................. 628
Installing wiper blades .................. 628
Flat tire ............................................... 629
Preparing the vehicle .................... 629
Mounting the Minispare wheel ...... 629Batteries............................................. 634
Disconnecting starter battery ....... 636
Removing starter battery .............. 637
Charging battery ........................... 637
Reinstalling starter battery ........... 638
Reconnecting starter battery ........ 638
Jump starting...................................... 639
Towing the vehicle.............................. 642
Installing towing eye bolt .............. 644
Fuses.................................................. 645
Aids for replacing fuses ................ 646
Fuse boxes in engine
compartment ................................ 646
Fuse boxes in passenger
compartment ................................ 647
Emergency engine shut-down ....... 648

315 Controls in detail
Starter switch positions
Starter switch positions
SmartKeyStarter switch
0For removing SmartKey
1Power supply for some electrical con-
sumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position.
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.
If a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in instrument cluster” (
page 544).
3Starting positionFor information on starting the engine us-
ing the SmartKey, see “Starting with the
SmartKey” (
page 359).
Warning!
G
When leaving the vehicle, always remove the
SmartKey or SmartKey with KEYLESS-GO*
from the starter switch, take it with you, and
lock the vehicle. Do not leave children unat-
tended in the vehicle, or with access to an
unlocked vehicle. Unsupervised use of vehi-
cle equipment may cause an accident
and/or serious personal injury.
i
When you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps (ex-
cept high beam headlamp indicator lamp and
turn signal indicator lamps if activated) should go
out when the engine is running. This indicates
that the respective systems are operational.
i
When the SmartKey is removed from the
starter switch and the automatic transmission is
in a position other thanP, the automatic trans-
mission automatically shifts to P.
!
If the SmartKey cannot be turned in the
starter switch, the battery may not be sufficient-
ly charged.


Check the battery and charge it if necessary
(page 634).


Get a jump start (
page 639).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.

361 Controls in detail
Driving and parking

If you are starting the engine with
KEYLESS-GO: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO.
or

Remove the KEYLESS-GO* start/stop
button from starter switch.

Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO.

Repeat the starting procedure
(page 359). Remember that extend-
ed starting attempts can drain the bat-
tery.

Get a jump start (
page 639).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.

Call Roadside Assistance.

Notify an authorized Mercedes-Benz
Center.
Driving off
Depress the brake pedal.
The gear selector lever can now be
used.

Shift automatic transmission toD orR.

Release the brake pedal.

Carefully depress the accelerator
pedal.
The electric parking brake is automati-
cally released (
page 364).
The red brake warning 0 (USA only)
or ! (Canada only) in the instru-
ment cluster goes out.
Once the vehicle is in motion, the auto-
matic central locking system engages
and the locking knobs in the doors
move down.
After a cold start, the automatic transmis-
sion shifts at a higher engine revolution.
This allows the catalytic converter to reach
its operating temperature earlier.
i
Wait for the gear selection process to com-
plete before setting the vehicle in motion.
i
Shifting from gear position P to position R,
N, or D is only possible with the brake pedal de-
pressed. Without the brake pedal depressed, the
gear selector lever can be moved, but the park-
ing pawl remains engaged, not allowing shifting
to occur.
i
After driving off the doors and the trunk lock
automatically.
You can open a locked door from the inside.
Open door only when conditions are safe to do
so.
You can deactivate the automatic locking using
the COMAND system (
page 223).


465 Controls in detail
Useful features
Roadside Assistance button• and
Information button¡
The Roadside Assistance button• and
the Information button¡ are located in
the storage compartment below the front
armrest (
page 448).
1Information button¡
2Roadside Assistance button•Roadside Assistance button•

Press and hold Roadside Assistance
button • (for longer than
2 seconds).
A call to a Mercedes-Benz Roadside As-
sistance dispatcher will be initiated.
The button will flash while the call is in
progress. The message:

“Connecting call” appears in the
multifunction display


“Roadside Assistance Activated”
appears in the COMAND display
and the audio system is muted.
When the connection is established, the
message:


“Call connected” appears in the multi-
function display


“Roadside Assistance Activated”
appears in the COMAND display The Tele Aid system will transmit data gen-
erating the vehicle identification number,
model, color and location (subject to avail-
ability of cellular and GPS signals).
A voice connection between the Roadside
Assistance dispatcher and the occupants
of the vehicle will be established.

Describe the nature of the need for as-
sistance.
The Mercedes-Benz Roadside Assistance
dispatcher will either dispatch a qualified
Mercedes-Benz technician or arrange to
tow your vehicle to the nearest authorized
Mercedes-Benz Center. For services such
as labor and/or towing, charges may ap-
ply. Refer to the Roadside Assistance Man-
ual for more information.
These programs are only available in the
USA:


Sign and Drive services: Services such
as jump start, a few gallons of fuel or
the replacement of a flat tire with the
vehicle spare tire are obtainable.
vehicle’s approximate location if they
receive an automatic SOS signal and cannot
make voice contact with the vehicle occu-
pants.

543 Practical hints
What to do if …?
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Resetting activated head restraints
(S 600 only)
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Batteries
Jump starting
Towing the vehicle
Fuses

639 Practical hints
Jump starting
Jump starting
If the starter battery is discharged, the en-
gine can be started with jumper cables and
the battery of another vehicle. Observe the
following:

Jump starting should only be performed
when the engine and catalytic convert-
er are cold.


Do not start the engine if the battery is
frozen. Let the battery thaw out first.


Only use 12-volt battery to jump start
y o ur ve h i c l e . J u m p s t a r t i n g w i t h a m o r e
powerful battery could damage the ve-
hicle’s electrical system, which will not
be covered by the Mercedes-Benz Lim-
ited Warranty.


Only use jumper cables with sufficient
cross-section and insulated terminal
clamps.


Always make sure that the jumper ca-
bles are not on or near pulleys, fans or
other parts that move when an engine
is started or running.
Warning!
G
Failure to follow these directions will cause
damage to the electronic components, and
can lead to a battery explosion and severe
injury or death.
Never lean over batteries while connecting
or jump starting, you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water, and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and very explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
Attempting to jump start a frozen battery
can result in it exploding, causing personal
injury.
Read all instructions before proceeding.
!
Do not tow-start the vehicle.
!
Jump starting should only be performed on
the starter battery installed in the engine com-
partment.
Avoid repeated and lengthy starting attempts.
Do not attempt to start the engine using a bat-
tery quick charge unit.
If engine does not run after several unsuccessful
starting attempts, have it checked at the nearest
authorized Mercedes-Benz Center.
Excessive unburned fuel generated by repeated
failed starting attempts may damage the catalyt-
ic converter and may present a fire risk.
Make sure the jumper cables do not have loose
or missing insulation.
Make sure the cable clamps do not touch any
other metal part while the other end is still at-
tached to a battery.

640 Practical hintsJump startingJump starting should only be performed on
the starter battery. The starter battery is
located in the engine compartment on the
passenger side (
page 634).

Make sure the two vehicles do not
touch.

Secure vehicle in place with electric
parking brake.

Shift the automatic transmission toP.

Turn off all electrical consumers, ex-
cept hazard warning flashers or work
lights.

Open the hood (
page 492).

Start the engine of the vehicle with the
charged battery and run at idle speed.1Positive terminal of your vehicle’s
battery
2Positive terminal of other vehicle’s
battery
3Negative terminal of other vehicle’s
battery
4Negative clamp
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 634).
i
Vehicles with KEYLESS-GO: remove the
KEYLESS-GO button (
page 316) and use the
SmartKey with KEYLESS-GO like a normal
SmartKey.

641 Practical hints
Jump starting

Remove red cover from positive
terminal 1.

Connect positive terminal2 of the
charged battery with positive
terminal1 of the discharged battery
with the jumper cable. Clamp cable to
charged battery2 first.

Connect negative terminal3 of
charged battery to jumper cables and
attach other end4 to a suitable
ground point on the vehicle.

Get into vehicle and start engine within
30 seconds.
If the starting attempt does not suc-
ceed: 
Turn the SmartKey in starter switch
to position 0.

Take out the SmartKey.

Turn off engine of donor vehicle, re-
start it and let it run at idle speed
for several minutes.

Disconnect the jumper cable during
this time.

Reconnect jumper cable as de-
scribed before.

Restart engine.

While the engine is running, switch off
several electrical consumers such as
the blower.

Disconnect jumper cables first from
ground point4 and negative
terminal3, then from positive
terminals1 and2.

Have the battery checked at the near-
est authorized Mercedes-Benz Center.
!
Never invert the terminal connections.

643 Practical hints
Towing the vehicle
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run


there is a malfunction in the brake sys-
tem


there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey is in
starter switch position 2 and automatic
locking is deactivated (
page 223).
Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.i
The automatic transmission will remain
locked in position P and the SmartKey will not
turn in the starter switch if the consumer battery
is disconnected or discharged. See information
on the battery (
page 634) or on jump starting
(
page 639).
i
To signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position 2 and activate the com-
bination switch for the left or right turn signal in
the usual manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
!
When towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position 2, or
KEYLESS-GO* start/stop button (
page 317)
in position 2, the vehicle doors lock if the left
front wheel as well as the right rear wheel are
turning at vehicle speeds of approximately
9mph (15km/h) or more.
Switch off the tow-away alarm (
page 76).
To prevent the vehicle doors from locking, deac-
tivate the automatic central locking
(
page 313).
Towing of the vehicle should only be done using
the properly installed towing eye bolt. Never at-
tach tow cable, tow rope or tow rod to vehicle
chassis, frame or suspension parts.

681 Index
Batteries, vehicle 634
Charging 637
Discharged, Jump starting 639
Disconnecting 636
For electrical consumers 634
For starter 634
Message in display 586
Reconnecting 638
Removing 637
Bead 526
Beverage holder see Cup holder
Bi-Xenon headlamps see Headlamps
Bluetooth
Settings (COMAND) 217
Brake assist system (BAS Plus) 71
Brake assist system (BAS) 71
Brake fluid 490, 662, 663
Brake lamp bulbs 622
Brake lamp, high mounted 622
Brake pads
Message in display 575
Brake warning lamp 29
Brakes 480
Warning lamp 545Break-in period 478
Bulbs, replacing 621
Additional turn signals 622
Brake lamps 622
Fog lamps 622
Front lamps 622
High beam 622
High mounted brake lamp 622
License plate lamps 622
Low beam 622
Parking and standing lamps 622
Rear fog lamp 622
Turn signal lamps 622
C
CAC (Customer Assistance Center) 670
California retail buyers and lessees, impor-
tant notice for 15
Can holder see Cup holder
CAN system 670
Canceling
Cruise control 382
Capacities and recommended
fuel/lubricants 661Cargo area see Trunk
Cargo tie-down hooks 453
Carpets, Cleaning and care of 542
Catalytic converter 487
CD
Ejecting (COMAND) 109
Loading (COMAND) 107
Menu overview (COMAND) 110
Playback options (COMAND) 114
Selecting a medium (COMAND) 112
Selecting a track (COMAND) 113
CD (COMAND) 104
Central locking
Automatic 313
Locking/unlocking from inside 314
Central locking/unlocking switches 314
Certification label 652
Change of address or ownership 16
Changing
Vehicle level (ABC*) 404
Vehicle level (Airmatic) 402