Rear battery MERCEDES-BENZ S550 2007 W221 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: S550, Model: MERCEDES-BENZ S550 2007 W221Pages: 705
Page 350 of 705
349 Controls in detail
Lighting
Interior lighting in the front
The controls are located in the overhead
control panel.
1Left reading lamp on/off
2Rear interior lamps on/off
3Front interior lighting on/off
4Interior lighting control
5Right reading lamp on/offAutomatic control
Deactivating: Press button4.
The OFF indicator lamp next to the but-
ton comes on.
The interior lighting remains switched
off in darkness, even when you:
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the trunk
Activating: Press button4.
The interior lighting switches on in
darkness when you:
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the trunkThe interior lighting switches off auto-
matically following an adjustable time
delay (
page 226).
Manual control
Switching on/off front interior light-
ing: Press button 3.
Switching on/off rear interior light-
ing: Press button 2.
Switching on/off front reading
lamps: Press button 1 or 5.
The reading lamps are integrated into
the interior rear view mirror.
Ambient lighting: the brightness of
the ambient lighting is adjusted via
COMAND (
page 79).
!
Leaving an interior light switch in the ON po-
sition for extended periods of time with the en-
gine turned off could result in a discharged
battery.
i
If the door remains open, the interior lighting
switches off automatically after approximately
5minutes.
An interior lamp switched on manually does not
go out automatically.
Page 431 of 705
430 Controls in detailAutomatic climate controlDeactivating
Press button; (
page 426) up or
down.
The indicator lamp on the button goes
out.
The previous settings are once again in
effect, except air recirculation mode
stays off.
Windshield fogged on the outside
Switch the windshield wipers on
(page 351).
Press buttonU (
page 426) up or
down.
The indicator lamp on the button
comes on.
Rear window defroster
Activating
Switch on the ignition (
page 315).
Press button< (
page 426) up or
down.
The indicator lamp on the button
comes on.
Deactivating
Press button< (
page 426) up or
down.
The indicator lamp on the button goes
out.
Maximum cooling MAXCOOL (USA only)
If U is selected on both the left and
right side and there is a high demand for
cooling, the display “MAXCOOL” appears
in the COMAND display.
This provides the fastest possible cooling
of the vehicle interior (when windows and
tilt/sliding sunroof or tilt/sliding panel*
are closed).
!
The rear window defroster uses a large
amount of power. To keep battery drain to a min-
imum, switch off the defroster as soon as the
rear window is clear.
i
The defroster is automatically deactivated
after some time of operation depending on the
outside temperature.Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.
i
If the rear window defroster switches off too
soon and the indicator lamp goes out, this indi-
cates that too many electrical consumers are op-
erating simultaneously and the load on the
battery is reducing available voltage. The system
responds automatically by deactivating the rear
window defroster.
i
Maximum cooling MAXCOOL is only avail-
able when the engine is running.
Page 459 of 705
458 Controls in detailUseful features1Center console cigarette lighter
1Rear center console lighter
Switch on the ignition (
page 315).
Push in cigarette lighter1.The lighter will pop out automatically
when hot.
Power outlet
The power outlet is located in the rear cen-
ter console.
Switch on the ignition (
page 315).
Flip up cover1 and insert electrical
plug (cigarette lighter type).
!
The lighter socket can be used to accommo-
date 12V DC electrical accessories (up to a max-
imum of 85 W) designed for use with the
standard “cigarette lighter” plug type. Keep in
mind, however, that connecting accessories to
the lighter socket (for example extensive con-
necting and disconnecting, or using plugs that do
not fit properly) can damage the lighter socket.
With the socket damaged, the lighter may no
longer be able to be placed in the heating
(pushed-in) position, or the lighter may pop out
too early with the lighter not hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with a stan-
dard “cigarette lighter” plug type to the 12V
power outlets (
page 458) in your vehicle
whenever possible.
i
Operation of the rear door lighters is only
possible, if the override switch (
page 67) is de-
activated.
i
If the engine is off and the cigarette lighter is
being used extensively, the vehicle battery may
become discharged.
i
The power outlet can be used to
accommodate 12V DC electrical accessories
(e.g. air pump, auxiliary lamps) up to a maximum
of 180 W.
If the engine is off and the outlet is being used
extensively, the vehicle battery may become dis-
charged.
Page 463 of 705
462 Controls in detailUseful featuresTele Aid
The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:
automatic and manual emergency
roadside assistance, and
informationThe Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and mo-
bile phone and GPS coverage are available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the COMAND
volume thumbwheel , on the lower
part of the front central console
(
page 89).
To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.
System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated.
If a malfunction is detected, the indicator
lamps in the SOS button, the Roadside As-
sistance button• and the Information
button¡ stay on longer than
10 seconds or do not come on. The mes-
sage “Tele Aid not activated” or “Tele Aid
inoperative” appears in the multifunction
display.
!
The initial activation of the Tele Aid system
may only be performed by completing the sub-
scriber agreement and placing an acquaintance
call using the Information button¡. Failure
to complete either of these steps will result in a
system that is not activated.
If you have any questions regarding activation,
please call the Response Center at
1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
i
The Tele Aid system utilizes the mobile
phone network for communication and the GPS
(Global Positioning System) satellites for vehicle
location. If either of these signals are unavail-
able, the Tele Aid system may not function and if
this occurs, assistance must be summoned by
other means.
i
The SOS button is located above the interior
rear view mirror (
page 464).
The Roadside Assistance button• and the
Information button¡ are located below the
center armrest cover (page 465).
Page 567 of 705
566 Practical hintsWhat to do if …?Display
Possible cause/consequence
Possible solution
Next Service X
due in ... days
due in ... mls (km)
Service X must be carried out in ... days or
after ... miles (kilometers) (
page 532).
Have the maintenance service carried out by an authorized
Mercedes-Benz Center.
Only shift to
position 'P' when
vehicle is stationary
You have tried to Shift the automatic trans-
mission to P using the gear selector lever al-
though the vehicle is still in motion.
Stop the vehicle.
Park Assist
currently unavailable
See Oper. Manual
You attempt to activate Park Assist* even
though you have switched off the radar sen-
sors* on the vehicle.
Check if the radar sensors* may be switched on (
page 256).
Switch on the radar sensors* using the instrument cluster
control system.
Park Assist* is deactivated because the
area around the sensors* in the front or the
rear bumper (
page 538) is dirty.
Clean the front and rear bumper (
page 538).
Park Assist* is deactivated because the
battery voltage is insufficient.
Have the battery checked by an authorized Mercedes-Benz
Center.
Park Assist* is switched off because the ra-
dar sensor system* is temporarily inopera-
tive due to electromagnetic interference
near television and radio transmitter sta-
tions, toll stations, speed measuring sys-
tems, etc.
Wait until the message in the multifunction display disappears.
Page 616 of 705
615 Practical hints
Unlocking/locking in an emergency
Unlocking the trunk
A minimum height clearance of 5.9 ft.
(1.80 m) is required to open the trunk lid.
1Trunk lid lock
Insert the mechanical key into the
trunk lid lock1 until it stops.
Turn mechanical key all the way to the
left.
The trunk opens.
Turn the mechanical key back and re-
move it from the trunk lid lock.
Locking the vehicle
If you cannot lock the vehicle with the
SmartKey or KEYLESS-GO*, do the follow-
ing:
Close the front passenger door, the
rear right door and the trunk.
Open the driver’s door and the rear left
door.
Press the central locking switch on the
driver’s door (
page 314).
The locking knobs of the front passen-
ger door and the rear doors move
down.
If the vehicle battery is disconnected or
drained:
Press down the locking knobs of
the front passenger door and the
rear doors manually.
Exit the vehicle.
Close the driver’s door.
Enter the vehicle through the rear left
door.
Press down the locking knob of the
driver’s door.
Exit the vehicle.
Close the rear left door.
The vehicle is locked.
!
The trunk lid swings open upwards automat-
ically. Always make sure that there is sufficient
overhead clearance.
!
To prevent inadvertent lockout, make sure
to have the SmartKey or SmartKey with KEY-
LESS-GO* with you before proceeding with the
next step. The next step will lock the vehicle.
Page 643 of 705
642 Practical hintsTowing the vehicleMercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment. This method is pref-
erable to other types of towing.
When circumstances do not permit the
recommended towing methods, the vehi-
cle may be towed with all wheels on the
ground or front wheels raised only so far as necessary to have the vehicle moved to a
safe location where the recommended
towing methods can be employed.!
Do not tow-start the vehicle.
!
Use flatbed or wheel lift/dolly equipment
with SmartKey in starter switch turned to posi-
tion 0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the ESP
® (page 73), the tow-away
alarm (
page 76) and the automatic central
locking (page 313).
If the vehicle’s transmission is damaged, only
have it towed with the drive shaft disconnected.
!
Make sure that the electric parking brake is
released. If the electric parking brake is malfunc-
tioning, release it mechanically (
page 616).
!
In vehicles with KEYLESS-GO, insert the
SmartKey into the starter switch under the
KEYLESS-GO button and turn the SmartKey in
the starter switch to 0.
!
If the vehicle is towed with the front axle
raised, the engine must be shut off (SmartKey in
starter switch starter switch position 0 or 1).
Otherwise the ESP
®/ETS will immediately be en-
gaged and will apply the rear wheel brakes.
While towing, the battery must be connected and
charged. Otherwise:
you will not be able to switch on the ignition
you will not be able to engage the automatic
transmission in position N
When towing the vehicle with all wheels on the
ground, the automatic transmission must be
shifted to N and the SmartKey must be in starter
switch position2.
In vehicles with KEYLESS-GO*, you must use the
starter switch under the KEYLESS-GO* button
(
page 315).
When towing the vehicle with all wheels on the
ground or the front axle raised, the vehicle may
be towed only for distances up to 30 miles
(50 km) and at a speed not to exceed 30 mph
(50 km/h).
!
To be certain to avoid a possibility of dam-
age to the drivetrain, however, we recommend
the drive shaft be disconnected at the rear axle
drive flange for any towing beyond a short tow to
a nearby garage.
Page 644 of 705
643 Practical hints
Towing the vehicle
Warning!
G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:
the engine will not run
there is a malfunction in the brake sys-
tem
there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
as that will be necessary to adequately con-
trol the towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make sure the SmartKey is in
starter switch position 2 and automatic
locking is deactivated (
page 223).
Warning!
G
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.i
The automatic transmission will remain
locked in position P and the SmartKey will not
turn in the starter switch if the consumer battery
is disconnected or discharged. See information
on the battery (
page 634) or on jump starting
(
page 639).
i
To signal turns while being towed with the
hazard warning flasher in use, turn SmartKey in
starter switch to position 2 and activate the com-
bination switch for the left or right turn signal in
the usual manner – only the selected turn signal
will operate.
Upon canceling the turn signal, the hazard warn-
ing flasher will operate again.
!
When towing the vehicle with all wheels on
the ground, please note the following:
With the automatic central locking activated and
the SmartKey in starter switch position 2, or
KEYLESS-GO* start/stop button (
page 317)
in position 2, the vehicle doors lock if the left
front wheel as well as the right rear wheel are
turning at vehicle speeds of approximately
9mph (15km/h) or more.
Switch off the tow-away alarm (
page 76).
To prevent the vehicle doors from locking, deac-
tivate the automatic central locking
(
page 313).
Towing of the vehicle should only be done using
the properly installed towing eye bolt. Never at-
tach tow cable, tow rope or tow rod to vehicle
chassis, frame or suspension parts.
Page 681 of 705
680 IndexAquaplaning see Hydroplaning
Armrest 448, 450
Ashtrays 456
Aspect ratio 526
Audio (COMAND) 104
CD mode 111
DVD mode 111
MP3 mode 111
Audio (Control system instrument
cluster) 248
CD changer 249
DVD changer 249
Audio DVD
Fast forward/rewind (COMAND) 113
Menu overview (COMAND) 110
Pause function (COMAND) 112
Stop function (COMAND) 112
Auto-dimming, Rear view mirrors 334
Automatic climate control 424
Adjusting air distribution
(COMAND) 230
Adjusting air flow from air vents
(COMAND) 233
Adjusting air volume (COMAND) 230
Adjusting the footwell temperature
(COMAND) 232Air recirculation mode 431
Central climate control menu
(COMAND) 231
Central menu for rear climate control*
(COMAND) 234
Defrosting 429
Operating the rear climate control*
from the front 234
Operating via COMAND 229
Rear window defroster 430
Selecting Mono mode
(COMAND) 232
Setting temperature (COMAND) 230
Setting the temperature 429
Setting the temperature in the rear
passenger compartment 435
Switching cooling on or off
(COMAND) 231
Automatic headlamp mode 255, 343
Automatic lighting control, Interior
lighting 349
Automatic locking when driving 313
Automatic shift program 374
Automatic transmission
Accelerator position 373
Automatic shift program 374Emergency operation (limp-home
mode) 377
Fluid 661
Fluid level 497
Gear ranges 372
Gear selector lever 367
Gear shifting malfunctions 377
Hill start assist system 374
Kickdown 373
Program mode selector switch 374
Shifting procedure 369
Starting the engine 359
Steering wheel gearshift control 375
Transmission fluid 497
Transmission positions 370
B
Backup lamps
Replacing bulbs 622
Bar 526
BAS 71
Batteries, SmartKey
Checking battery condition 311
Replacing 619
Batteries, SmartKey with KEYLESS-GO*
Checking battery condition 311
Replacing 619
Page 686 of 705
685 Index
Dynamic Rear View Monitor* 413
Parallel parking 417
Reverse parking (back-in
parking) 415
Switching on 415
View through the camera 413
E
Easy-entry/exit feature 328
COMAND menu 224
EBP 71
ELCODE 672
Electric parking brake 364
Electrical fuses see Fuses
Electrical outlet see Power outlet
Electrical system, Technical Data 659
Electronic Brake Proportioning see EBP
Electronic Stability Program see ESP
®
Emergency call system 462
Emergency calls, Tele Aid 463
Emergency engine shut-down 648
Emergency operation (Limp-Home
Mode) 377
Emergency operations
Locking the vehicle 614
mechanically releasing the parking
brake 616Releasing from inside 440
Remote door lock 469
Remote door unlock 468
Tilt/sliding sunroof or tilt/sliding
panel* 617
Unlocking the trunk 615
Unlocking the vehicle 614
Emergency tensioning device see ETD
Emergency, In case of
Battery, Jump starting 639
First aid kit 611
Flat tire 629
Fuses 645
Instrument cluster, Indicator
lamps 544
Roadside Assistance 16
Roadside Assistance (Tele Aid) 465
Towing the vehicle 642
Emission control 488
Emission control information label 652
Emission control system warranties 14
Engine
Belt layout 653
Cleaning 536
Compartment 492
Coolant 497, 662, 665Malfunction indicator lamp 547
Number 652, 672
Oil 496, 661, 663
Oils 494
Residual heat and ventilation 433
Starting 359
Technical data 654
Turning off 365
Engine coolant see Coolant
Engine oil 494
Adding 496
Additives 663
Checking level 494
Checking level (Dipstick) 495
Checking level (Instrument cluster con-
trol system) 494
Consumption 494
Dipstick 495
Filler neck 496, 497
Messages in display 495, 602
Recommended engine oils and oil
filters 661
Viscosity 672
ESP
®
72
Messages in display 572, 582
Warning lamp 549