hood release MERCEDES-BENZ S600 2003 W220 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2003, Model line: S600, Model: MERCEDES-BENZ S600 2003 W220Pages: 416, PDF Size: 6.81 MB
Page 21 of 416
21 At a glance
Cockpit
Item
Page
1
Combination switch
Turn signals
Windshield wipers
High beam
46
47
123
2
Cruise control lever
Cruise control
Distronic*
203
196
199
3
Instrument cluster
22
4
Multifunction steering
wheel
24
Item
Page
5
Gear range indicator, clock
22
6
Lever for voice control sys-
tem*, see separate operat-
ing instructions
7
Front Parktronic* warning
indicator
220
8
Overhead control panel
27
9
Glove box lock
224
10
Glove box lid release
224
11
Glove box
224
12
Center console
25
13
Starter switch
31
Item
Page
14
Horn
15
Steering wheel adjustment
stalk
Heated steering wheel*
38
235
16
Parking brake pedal
44
17
Hood lock release
263
18
Parking brake release
44
19
Door control panel
28
20
Exterior lamp switch
120
21
Headlamp washer button
171
22
Front Parktronic* warning
indicator
220
Page 263 of 416
263 Operation
Engine compartment
Engine compartment
Hood
Opening
The hood lock release lever is located in
the driver’s footwell to the left of the park-
ing brake pedal.
1Hood lock release
Pull lever 1 towards you in the direction
of the arrow.
The hood is unlocked and handle2 will
extend out of the radiator grill.
2Handle for opening the hood
Pull handle 2 to its stop out of radiator
grill.
Pull up on the hood (do not pull up on
the handle) and then release it.
The hood will be automatically held
open at shoulder height by gas-filled
struts.
Warning!
G
Do not pull the release lever while the vehi-
cle is in motion. Otherwise the hood could
be forced open by passing air flow.
!To avoid damage to the windshield wip-
ers or hood, never open the hood if the
wiper arms are folded forward away
from the windshield.
Warning!
G
To help prevent personal injury, stay clear of
moving parts when the hood is open and the
engine is running. Make sure the hood is
properly closed before driving. When closing
the hood, use extreme caution not to catch
hands or fingers.
The radiator fan may continue to run for ap-
proximately 30 seconds or even restart af-
ter the engine has been turned off. Stay
clear of fan blades.
Page 333 of 416
333 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
1Headlamp cover for fog lamp
2Headlamp cover for high beam head-
lamp bulb, parking and standing lamp
3Headlamp cover for low beam
(Bi-Xenon* or halogen) headlamp bulb4Bulb socket for fog lamp
5Bulb socket for parking and standing
lamp
6Electrical connector for high beam
headlamp bulb
7Electrical connector for low beam
headlamp bulb
8Bulb socket for turn signal lampReplacing low beam bulbs
Bi-Xenon* headlamp
Halogen headlamp
Switch off the lights.
Open the hood (
page 263).
Press the tab on cover3 and remove
cover.
Pull connector7 off of the lamp.
Release the retaining springs and take
out the bulb.Warning!
G
Do not remove the cover for the Bi-Xenon
headlamp. Because of high voltage in xenon
lamps, it is dangerous to replace the bulb or
repair the lamp and its components. We rec-
ommend that you have such work done by a
qualified technician.
Page 334 of 416
334 Practical hintsReplacing bulbs
Insert the new bulb in the socket so
that the base is in the recess on the
lower left.
Attach the retaining springs.
Insert connector7 into the bulb.
Press cover3 onto the housing until
the tab engages.Replacing high beam bulbs
Switch off the lights.
Open the hood (
page 263).
Press the tab on cover2 and remove
cover.
Pull connector 6 off of the bulb.
Apply pressure on the bulb contacts
from above until the bulb releases from
the retaining springs.
Remove bulb.
Insert the new bulb in the socket with
the marking facing upward.
Press the bulb upward on the contacts
until it engages in the retaining springs.
Insert connector6 onto the bulb.
Press cover2 onto the housing until
the tab engages.Front turn signal lamp bulb
Switch off the lights.
Open the hood (
page 263).
Twist bulb socket8 counterclockwise
and pull out.
Gently push bulb into socket, turn
counterclockwise and remove.
Insert new bulb in socket, push in and
twist clockwise.
Reinstall bulb socket in lamp and twist
clockwise until it engages.