window MERCEDES-BENZ S65AMG 2008 W221 Owner's Guide

237 Control systems
COMAND system settings
Setting the time/date format
Select “Vehicle”
“System Settings”

“Time”
“Format”.
The format list appears. The dots R in
front of the list entries indicate the cur-
rent setting.
Changing format setting:
Select desired format.
Saving setting and exit the menu:
Slide omp.
Voice Control* settings
Switching help window on or off
Select “Vehicle”
“System Settings”

“Voice Control”.
Select “Help Window”.
You can switch the help window on or
off. A checkmark appears when the
help window is switched on.Individualization
Using individualization, you can fine-tune
Voice Control* to your own voice and thus
improve voice recognition. The ability of
the system to recognize the commands of
other users does not deteriorate as a re-
sult.
Individualization consists of two parts. You
train the system to recognize digits in the
first part and specific commands in the
second part.
Starting new individualizationSelect “Vehicle”
“System Settings”

“Voice Control”
“Start new indi-
vidualization”.
A prompt appears asking whether you
would like further information.
Select “Yes” or “No”.
If you select “No”, the first part of indi-
vidualization begins.
If you select “Yes”, an information dis-
play will be shown with audio instruc-
tion.
Closing display: Select “OK”.
The first part of individualization be-
gins.
At the end of the first part, you will see
a prompt asking whether you want to
begin the second part.
Select “Yes” or “No”.
If you select “No”, individualization will
be canceled. The data from the first
part is saved automatically.
If you select “Yes”, the second part be-
gins.
Individualization is completed at the end of
the second part. You will see a message to
this effect. The data from the second part
is saved automatically.iIt is only possible to start individualization
with the vehicle stationary. After starting the
session, the system will guide you through the in-
dividualization by means of acoustic instruc-
tions.

238 Control systems
COMAND system settings
Canceling during the first or second part
of individualization
Select “Cancel”.
A prompt appears asking whether you
really do want to cancel.
Select “Yes” or “No”.
If you select “Yes”, individualization will
be canceled. The data from the part at
which you exited is not saved.
If you select “No”, the part at which you
stopped begins again.
Deleting existing individualization data
Select “Vehicle”
“System Settings”

“Voice Control”
“Delete individu-
alization”.
A prompt appears asking whether you
really do want to delete.
Select “Yes” or “No”.
The individualization data will either be
deleted or not, depending on your se-
lection.
Setting the system language
Select “Vehicle”
“System Settings”

“Language”.
The language list appears. A dot R in-
dicates the current setting.
Changing setting: Select desired lan-
guage.
The language is set.
Assigning the favorite button
1Favorite buttonYou can assign the following predefined
functions to the favorite buttonP:

“Rear Window Sunshade” (page 503)
You can use the favorite button to ex-
tend or retract the rear window sun-
shade. This is the default setting.

“Display OFF” (page 235)
You can use the favorite button to
switch the COMAND display on or off.

“Repeat Navigation Command”
(
page 213)
You can use the favorite button to re-
call the last announcement issued by
the navigation system.
Select “Vehicle”
“System Settings”

“Favorite”.
The list of predefined functions appears.
The dot R in front of the list entry indi-
cates the current setting.
Changing setting: Rotate ymz and
select desired function.
Saving setting and exit the menu:
Press n.

242 Control systems
COMAND vehicle menu
In this menu, you can program the follow-
ing vehicle functions:Setting night security illumination
(Exterior Lighting Delayed Switch-off)
Use this function to set whether and how
long you would like the exterior lighting to
illuminate during darkness after exiting the
vehicle and all doors closed.
The exterior lighting automatically goes
out after the delayed switch-off time has
expired.
You can select:

“0 sec.”, the delayed switch-off feature
is deactivated

“15 sec.”, “30 sec.”, “45 sec.”, or
“60 sec.”, the delayed switch-off fea-
ture is activated
Select “Vehicle”.
The main area is active.
Selecting “Exterior Lighting Delayed
Switch-off” menu: Slide omp or
rotateymz.
Confirming selection: Press n.
Selecting length of time: Slide qmr
or rotate ymz.
Confirming selection: Press n.
or
Select “Vehicle”
“Vehicle”
“Exte-
rior Lighting Delayed Switch-off”.
A selection list appears.
The current setting is indicated by a
dotR.
FunctionPage
Exterior Lighting Delayed
Switch-off242
Locator Lighting243
Exterior Mirror Convenience Set-
tings244
Automatic Locking245
Easy Entry/Exit Feature246
Interior Ambient Light247
Interior Lighting Delayed
Switch-off248
Rear-window Sunshade249
Trunk Opening-height Restriction*249
iThe components and operating principles of
COMAND can be found on (
page 85).
iYou can reactivate this function within
10 minutes by opening a door.

249 Control systems
COMAND vehicle menu
Extending or retracting rear window
sunshade
This function is used to extend or retract
the rear sunshade.
Select “Vehicle”.
The main area is active.
Selecting “Rear-window Sunshade”
function: Slide omp or rotate ymz.
Extending or retracting rear window
sunshade: Press n.
or
Select “Vehicle”
“Vehicle”

“Rear-window Sunshade”.
Confirming selection: Press n.Trunk opening-height restriction*
on/off
Vehicles with trunk opening/closing sys-
tem*:
You can select whether the trunk lid should
open fully or only to the height of the roof.
Select “Vehicle”.
The main area is active.
Selecting “Trunk Opening-height Re-
striction” function: Slide omp or
rotateymz.
Confirming selection: Press n.
iThe components and operating principles of
COMAND can be found on (
page 85).
iIf you operate the rear-window sunshade via
COMAND or by using the favorite button
(
page 238), this takes precedence over the
buttons for the rear window sunshade in the rear
doors (
page 503).
iYou can program this function using the fa-
vorite button (
page 238).
iAt temperatures below -4°F (-20°C), the
rear window sunshade is switched off.
iThe components and operating principles of
COMAND can be found on (
page 85).


251 Control systems
COMAND automatic climate control
COMAND automatic climate control
You can operate the automatic climate
control via COMAND or via the buttons on
the front and rear* automatic climate con-
trol panel (
page 469).
Some of the special climate control func-
tions can only be set via COMAND.The following automatic climate control
functions can be operated via COMAND:
iThe components and operating principles of
COMAND can be found on (
page 85).
Warning!G
When operating the automatic climate con-
trol, the air that enters the passenger com-
partment through the air vents can be very
hot or very cold (depending on the set tem-
perature). This may cause burns or frostbite
to unprotected skin in the immediate area of
the air vents.
Always keep sufficient distance between un-
protected parts of the body and the air
vents. If necessary, use the air distribution
adjustment (
page 253) to direct the air to
air vents in the vehicle interior that are not
in the immediate area of unprotected skin.
Warning!G
Follow the recommended settings for heat-
ing and cooling given on the following pages
and pages in the “Controls in detail” part
(
page 469) Otherwise the windows could
fog up, impairing visibility and endangering
you and others.
FunctionPage
Temperature252
Air distribution253
Air volume253
Switching off cooling (“ACOFF”)254
Central climate control (“Mono”)255
Footwell temperature255
Air flow from air vents256
Rear climate control*257

254 Control systems
COMAND automatic climate control
Central climate control menu via
COMAND
The central climate control menu is in the
center of the climate control settings.
When the automatic climate control is
switched on, you will see “on” in the cen-
tral menu. The following functions can only
be operated in the central climate control
menu via COMAND:
Select climate control settings
Cen-
tral menu.Switching cooling on or off
The cooling function, only operational
when the engine is running, cools the vehi-
cle interior down to the selected tempera-
ture. The cooling function also
dehumidifies the air in the vehicle interior,
thus preventing the windows from fogging
up.The “AC
OFF” function is used to permanent-
ly switch off the cooling function of the au-
tomatic climate control system.
Select climate control settings
Cen-
tral climate control menu.
FunctionPage
Switching off cooling (“ACOFF”)254
Central climate control (“Mono”)255
Footwell temperature255
Air flow from air vents256
Rear climate control*257
iCondensation may drip out from underneath
the vehicle. This is normal and not an indication
of a malfunction.
Warning!G
If you turn off the cooling function, the
vehicle will not be cooled when weather
conditions are warm. The windows can fog
up more quickly. Window fogging may
impair visibility and endanger you and
others.

286 Control systems
Voice Control* introduction
Spelling
You may not need to spell the entire name
(street, intersection, city or point of inter-
est) especially if the name is lengthy. Spell-
ing the first three to five characters of the
name should be sufficient for the system
to recognize the name provided it is avail-
able on the navigation DVD.
The selection appearing on the COMAND
display is sorted based on your recognized
voice input and a matching algorithm.
You can use the commands “Next page” or
“Previous page” to scroll up or down in the
list.
Use the command “Correction” to start
over by again spelling the name.
Speak each character as clearly as you
can, especially when they sound very simi-
lar (d or e).Command types
The Voice Control System commands can
be categorized as:

General Commands
These are commands always available
to you as soon as the Voice Control
System is activated (for example
“Help” commands).

Local Commands
These are commands specific to the
currently active system shown in the
COMAND display (for example com-
mands to control the CD/DVD chang-
er).
For a complete list of commands
(
page 315).
Active System
The active system is the system currently
shown in the COMAND display.
If, for example, you listen to the radio while
the telephone system is active on the
COMAND display, you have to switch to
the radio using the command “Radio” be-
fore you can operate the radio.
iDuring Voice Control System operation visu-
al help windows also appear in the COMAND dis-
play (
page 288).

327 Control systems
Voice Control* troubleshooting
Voice Control* troubleshooting
Help function
To support the user, the Voice Control Sys-
tem contains an extensive help function.
The help function gives you:

General hints on how to best use the
Voice Control System

A listing of all available commands
Help commands
“Help voice control”
Using the command “Help voice control”
will give you information on how to best
use the Voice Control System.
“Help”
In a main menu, help can be accessed at
any time by saying the command “Help”.
The Voice Control System will then read
out the available functions and commands
of all systems.In a submenu, help can also be accessed at
any time by saying the command “Help”.
The Voice Control System will then read
out an option list of all available functions
and commands available in the particular
submenu.
You can also use the help function to ac-
cess help for a specific system. To access
help for the phone operation, you would
speak the command “Help Telephone”.
If you wish to execute the last command
read out:
Press!.
Help window
You can use the help window to view a se-
lection of valid commands on the
COMAND display.
The help functions can be switched on or
off via COMAND in the “System settings”
menu (
page 237).
Entering digits and spelling
Entering digits

Digits from “Zero” to “Nine” may be
used.

Speaking phone numbers in digit
blocks of 3 to 5 digits has proven a
very reliable method for the input of
phone numbers.
Spelling

The letters of the English alphabet and
the digits 0 - 9 may be used.

Speak the letters in blocks of 5 - 7 let-
ters at a time.

Speak each individual letter clearly.

329 Control systems
Voice Control* troubleshooting
ProblemPossible cause/consequenceSuggested solution
Voice Control System does not recognize
commands.You have not operated the system from the
driver’s seat.Operate the Voice Control System only
by the driver as the microphone is
geared to the driver side.
You have spoken unclearly, too loudly or
too quietly.Speak the commands in a continuous
manner using a normal tone.
A blower is set to the highest setting, vents
are pointed at microphones or wind noise is
being created through open windows.Avoid loud disturbances.
Voice Control System does not recognize a
address book entry.The voice entries in the address book sound
too similar.When you create your address book en-
tries, select names with the greatest
possible acoustic differences: If for ex-
ample you have the names Smith and
Schmidt, choose for example “Smith
work” or “Schmidt John”.
Speak the command “List phone book”.
The system reads out the address book
entry by entry.
Press! when the desired entry is
being read out.
The entry is selected and the corre-
sponding number is dialed
(
page 295).

331 Controls in detail
Locking and unlocking
Starter switch positions
Seats
Steering wheel
Mirrors
Memory function
Fastening the seat belts
Lighting
Windshield wipers
Power windows
Driving and parkingAutomatic transmission
Instrument cluster
Driving systems
Air vents
Automatic climate control
Trunk
Power tilt/sliding sunroof
Panorama roof with power
tilt/sliding panel*
Loading and storing
Useful features