seats MERCEDES-BENZ S65AMG 2008 W221 Owner's Guide

353 Controls in detail
Seats
Head restraints
Front seat active head restraints
You cannot remove the active head re-
straint on the driver’s and front passen-
ger’s seats.For removal contact an authorized
Mercedes-Benz Center.
For information on active head restraints,
see “Active head restraints” (
page 55).
Head restraint height
1Head restraint height
Press the switch up or down in the di-
rection of arrow1.Head restraint adjusting
Manually adjust the head restraint. Push or pull on the upper edge of the
head restraint cushion to the desired
position.
Warning!G
For your protection, drive only with properly
positioned head restraints.
Adjust the head restraint so that it is as
close to the head as possible and the center
of the head restraint supports the back of
the head at eye level. This will reduce the po-
tential for injury to the head and neck in the
event of an accident or similar situation.
Do not drive the vehicle without the seat
head restraints. Head restraints are intend-
ed to help reduce injuries during an acci-
dent.
iAdjust the head restraint in such a way that
it is as close to the head as possible.
i Depending on the seat’s set fore and aft po-
sition, the head restraint height is automatically
pre-set.
i The head restraint on the front passenger’s
side is automatically lowered all the way down
while the vehicle is in motion if no one is sitting
on the seat. This helps you to acquire a better
all-round view.

354 Controls in detail
Seats
Luxury head restraint* adjusting
1Head restraint side cushions
2Adjusting head restraint forward and
backward
You can individually adjust side
cushions1 of the luxury head restraints.Adjusting side cushions: Pull or push
side cushions1 into desired position.
Adjusting forward or backward: Pull
or push head restraint in direction of
arrow2.
Rear head restraintsFolding head restraints back
The rear seat head restraints and the rear
seat power head restraints* can be folded
backward for increased visibility.
1Switch in the front center console
Switch on the ignition (page 344).
Press switch1 in the front center con-
sole briefly.
The rear head restraints will fold back-
ward.
Warning!G
When folding back the side cushions, never
reach between the side cushion and the
mounting post. You could otherwise be
trapped.
Warning!G
For safety reasons, always drive with the
rear head restraints in the upright position
when the rear seats are occupied.
Otherwise, the back of the head will not be
supported in the event of a collision. As a re-
sult, rear seat occupants could be injured.
Warning!G
Keep the area around head restraints clear
of articles (e.g. clothing) to not obstruct the
folding operation of the head restraints.

355 Controls in detail
Seats
Placing head restraints upright
Pull the rear head restraint upright until
it locks into position.Placing power head restraints* upright
(rear outer seats)
Switch on the ignition (page 344).
Press and hold switch1 in the front
center console (
page 354).
The rear outer seats head restraints
will place upright.
Pull the rear center seat head restraint
upright manually until it locks into posi-
tion.Rear power head restraints*
(rear outer seats)
1Placing upright head restraint
2Head restraint tilt
3Folding down head restraint
4Head restraint tilt
Switch on the ignition (page 344) or
open the respective door.
Press switch up in the direction of
arrow1.
The rear outer seats power head re-
straint will place upright.
!Make sure the head restraints engage when
placing them upright manually. Otherwise their
protective function cannot be ensured.
iWhen you fasten your seat belt in the rear,
the respective rear outer seat head restraint
places upright automatically.


356 Controls in detail
Seats
Press switch down in the direction of
arrow3.
The rear power head restraint will fold
down.
Press the switch forward or backward
in the direction of arrow2 or4.
The power head restraint will be tilted.
Luxury head restraints*
(rear outer seats)Adjustment
1Head restraint side cushions
2Head restraint height
You can individually adjust side
cushions1 of the luxury head restraints:
Adjusting side cushions: Pull or push
side cushions1 into desired position.
Adjusting head restraint angle: Push
or pull on the lower edge of the head re-
straint cushion in the direction of
arrow2.
Multicontour seats*, rear
You can adjust the rear outer multicontour
seats using the buttons on the center con-
sole.
1To select right rear passenger seat
2Massage setting, gentle
3Massage setting, vigorous
4To adjust position of backrest curva-
ture (lordosis)
5Lumbar region support
6Side bolster adjustment
7To select left rear passenger seat
Switch on the ignition (page 344).
Warning!G
When folding back the side cushions, never
reach between the side cushion and the
mounting post. You could otherwise be
trapped.


357 Controls in detail
Seats
Selecting a seat: Press rocker
switch1 or7 forward or backward.
The indicator lamp on the selected but-
ton lights up for a short while.
Gentle massage
Switching on: Press rocker switch2
forward.
Switching off: Pull rocker switch2
backward.
Vigorous massage
Switching on: Press rocker switch3
forward.
Switching off: Pull rocker switch3
backward.
Position of backrest curvature
Moving upward: Press rocker
switch4 forward.
Moving downward: Pull rocker
switch4 backward.Lumbar region support
Selecting greater curvature: Press
rocker switch5 forward.
Selecting less curvature: Pull rocker
switch5 backward.
Side bolster adjustment
Reducing width: Press rocker
switch6 forward.
Increasing width: Pull rocker
switch6 backward.
Easy-entry/exit feature
This feature allows for easier entry into and
exit from the vehicle. When entering and
exiting the vehicle, the driver’s seat is in its
maximum rearward position and the steer-
ing wheel is in its uppermost position.
The easy-entry/exit feature can be activat-
ed or deactivated in the “Vehicle” menu of
the COMAND system (
page 246).
Warning!G
You must make sure no one can become
trapped or injured by the moving steering
wheel and driver’s seat when the easy-en-
try/exit feature is activated.
To stop seat/steering wheel movement, do
one of the following:

Press seat adjustment switch
(
page 348).

Move steering wheel adjustment stalk
(
page 359).

Press one of the memory position but-
tons or the memory buttonM
(
page 366).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.

358 Controls in detail
Seats
With the easy-entry/exit feature activated,
the steering wheel and driver’s seat will re-
turn to their last set memory position or a
factory-set maximum forward position
when you:

close the driver’s door with the ignition
switched on

insert the SmartKey into the starter
switch or press the KEYLESS-GO*
start/stop button (
page 346) once
with the driver’s door closedWith the easy-entry/exit feature activated
the steering wheel tilts upwards and the
driver’s seat moves a few inches to the
rear when you:

remove the SmartKey from the starter
switch,
or

open the driver’s door with the
SmartKey in starter switch position0
or1 or the KEYLESS-GO* start/stop
button (
page 346) in position1
!Do not activate the easy-entry/exit feature
if the seat backrest is in an excessively reclined
position. Doing so could cause damage to front
or rear seats.
First move the seat backrest to an upright posi-
tion.
iFor safety reasons, the driver’s seat will not
return to its last set position with the easy-en-
try/exit feature activated if the system recogniz-
es the last set position as an extreme forward
position. Instead, the driver’s seat will remain at
or move to a factory-set maximum forward posi-
tion. To again fully return the driver’s seat toyour last set position or to memory position, ad-
just the seat to the desired position or press and
hold the respective memory position button
(
page 366).
iThe last set driver’s seat and steering wheel
positions are stored when

the ignition is switched off (page 344)

the position is stored in memory
(
page 365)
iIf the current position for the steering wheel
is in the uppermost tilt position, the steering
wheel will no longer be able to move upward
when the easy-entry/exit feature is activated.
If the current seat position falls into a factory-set
position range and the system recognizes the
current seat position to be rearward enough for
easy entry and exit, the driver’s seat will not
move to the rear when the easy-entry/ exit fea-
ture is activated.
The adjustment procedure is briefly interrupted
when the engine is started.
Warning!G
Let the system complete the adjustment
procedure before setting the vehicle in mo-
tion. All driver’s seat and steering wheel ad-
justments must be completed before setting
the vehicle in motion. Driving off with the
driver’s seat/steering wheel still adjusting
could cause the driver to lose control of the
vehicle.

366 Controls in detail
Memory function
MMemory button
1 2 3Memory position buttons
Switch on the ignition (page 344).
or
Open the respective door.
Storing positions into memory
Adjust the seat (page 347) to the de-
sired position.
On the driver’s side: Adjust the steering
wheel (
page 359) and the exterior
rear view mirrors (
page 361) to the
desired position.
Press memory buttonM.
Release memory buttonM and press
one of the memory position buttons
within 3 seconds.
All the settings are stored with the se-
lected position.
Recalling positions from memory
Press and hold one of the position
buttons until the seat, steering wheel
and exterior rear view mirrors have fully
moved to the stored positions.
!Do not operate the power seats using the
memory button if the seat backrest is in an ex-
cessively reclined position. Doing so could cause
damage to front or rear seats.
First move seat backrest to an upright position.
iReleasing the button immediately stops
movement to the stored positions.
The multicontour seat* and/or lumbar support
will continue to be adjusted.

368 Controls in detail
Fastening the seat belts
Warning!G
Always fasten your seat belt before driving
off. Always make sure all of your passengers
are properly restrained.
Failure to wear and properly fasten and
position your seat belt greatly increases
your risk of injuries and their likely severity
in an accident. You and your passengers
should always wear seat belts.
If you are ever in an accident, your injuries
can be considerably more severe without
your seat belt properly buckled. Without
your seat belt buckled, you are much more
likely to hit the interior of the vehicle or be
ejected from it. You can be seriously injured
or killed.
In the same crash, the possibility of injury or
death is lessened if you are wearing your
seat belt. The air bags can only provide the
protection they were designed to afford if
the occupants are using their seat belts
(
page 42).
Warning!G
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing position. Thus, we strongly recommend
that children be placed in the rear seats
whenever possible. Regardless of seating
position, children 12 years old and under
must be seated and properly secured in an
appropriately sized infant restraint, toddler
restraint, or booster seat recommended for
the size and weight of the child. For addi-
tional information, see “Children in the vehi-
cle” (
page 57).
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.
Warning!G
Never let more people ride in the vehicle
than there are seat belts available. Be sure
everyone riding in the vehicle is correctly re-
strained with a separate seat belt. Never use
a seat belt for more than one person at a
time.
Warning!G
Never ride in a moving vehicle with the seat
backrest in an excessively reclined position
as this can be dangerous. You could slide
under the seat belt in a collision. If you slide
under it, the seat belt would apply force at
the abdomen or neck. That could cause se-
rious or even fatal injuries. The seat back-
rest and seat belt provide the best restraint
when the wearer is in a nearly upright posi-
tion and the seat belt is properly positioned
on the body.

370 Controls in detail
Fastening the seat belts
Proper use of seat belts

Do not twist the seat belt when fasten-
ing.

Adjust seat belt so that the shoulder
portion is located as close as possible
to the middle of the shoulder (it should
not touch the neck). Never pass the
shoulder portion of the seat belt under
your arm.

Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.

Place the seat backrest in a nearly up-
right position.

Never use a seat belt for more than one
person at a time.

Do not fasten a seat belt around a per-
son and another object at the same
time. When using a seat belt to secure
infant restraints or toddler restraints or
children in booster seats, always follow
the child seat manufacturer’s instruc-
tions.

Check your seat belt during travel to
make sure that it is properly posi-
tioned.

Make sure the seat belt is always fitted
snugly. Take special care of this when
wearing loose clothing.For more information, see “Seat belts”
(
page 52).
Seat belt height adjustment
The vehicle automatically adjusts the seat
belt height for the driver’s and front pas-
senger’s seats as well as for the rear outer
seats. Comply with the instructions on how
to properly fasten a seat belt
(
page 368).
Warning!G
Do not pass seat belts over sharp edges.
They could tear.
Do not allow the seat belt to get caught in
the door or in the seat adjustment mecha-
nism. This could damage the seat belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the seat belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Damaged seat belts or seat belts that were
highly stressed in an accident must be re-
placed. Contact an authorized
Mercedes-Benz Center.

383 Controls in detail
Power windows
Power windows
Opening and closing power windows
The door windows are opened and closed
electrically. The switches

for all door windows are on the driver’s
door

for the front passenger side window
are on the front passenger door

for each rear side window are on the
rear doors
1Left front door window
2Right front door window
3Left rear door window
4Right rear door window
Warning!G
Do not keep any part of your body up against
the side window pane when opening a win-
dow. The downward motion of the pane may
pull that part of your body down between
the window pane and the door frame and
trap it there. If there is a risk of entrapment,
release the switch and press it again to
close the window.
Warning!G
When closing the windows, make sure that
there is no danger of anyone being harmed
by the closing procedure.
Activate the override switch (
page 63)
when children are riding in the back seats of
the vehicle. The children may otherwise in-
jure themselves, e.g. by becoming trapped
in the window opening.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pressed past the resis-
tance point and released, by pressing the
lower part of the respective switch again.
The door windows are equipped with the ex-
press-close and automatic reversal func-
tion. If the window encounters an
obstruction that blocks its path in a circum-
stance where you pressed the switch past
the resistance point and released it to close
the window, the automatic reversal function
will stop the window and open it slightly.