lock MERCEDES-BENZ SL-Class 2003 R230 Comand Manual

107 Telephone
Emergency call
If there is an active Tele Aid call, the tele-
phone main menu will disappear and you
will see the message “Phone off”.
After the Tele Aid call is ended, the tele-
phone main menu will reappear.
See your vehicle’s operator’s manual.Initiating an emergency call
If the telephone main menu or a memory
menu is displayed:

Press number key 1 longer than 2 se-
conds (quick-dialing).
The telephone begins dialing, the “End”
button is highlighted.
When the call is initiated, the call time
will appear.
Do not place the emergency call

Turn the right-hand rotary/push-
button v to highlight the “End” button
and press to confirm or press *.
Ending the call, use one of the three ways:

Press the right-hand rotary/push-
button v to confirm the “End” button.
or

Press a.
or

Press *.
P82.85-9154-31
Telephone is ready for operationiPlease ensure that the number stored in
the memory location is the number you
want to dial in case of an emergency
(default is 9-1-1).
The function will also be performed if
the telephone is locked.
P82.85-9155-31

130 NavigationDestination input
Turn the right-hand rotary/push-
button v to highlight the desired block
and press to confirm.
The selection menu “Destination Entry”
will appear.

Press the right-hand rotary/push-
button v longer than 2 seconds to cal-
culate the route (
page 141).Selecting a city center
You can activate the list “Center Entry” in
the main address menu (
page 123) or af-
ter selecting a city (
page 126).

Turn the right-hand rotary/push-
button v to highlight “Center” and
press to confirm.
The list “Center Entry” will appear.

Turn the right-hand rotary/push-
button v to highlight the desired entry
and press to confirm.
The selection menu “Destination Entry”
will appear.

Press the right-hand rotary/push-
button v longer than 2 seconds to cal-
culate the route (
page 141).
iThe house numbers usually appear on
the list in blocks, e.g.
1-5 odd numbers
42-50 even numbers
1-50 mixed numbers

163 Navigation
Route guidance
Main detour menu
1It is possible to block route sections
ahead
2Ends the detour function, the previous
route is calculated
3It is possible to block route sections in
the route list (
page 165)
Explanation corresponding 2

Detour has not yet been selected
You cannot select “Cancel”

Detour has been selected
“Cancel” is highlighted

Press ) while any menu is on the
screen during route guidance.
The main detour menu will appear.

Turn the right-hand rotary/push-
button v to highlight the desired
menu field and press the button.
^
Selecting a detour
P82.85-9222-31
1223
iTraffic jams are identified by the driver,
not by the COMAND.
If you switch off COMAND for more than
30 minutes during active route
guidance, all manually entered traffic
jams are deleted.

164 NavigationRoute guidanceTraffic jam ahead
If a traffic jam lies ahead, you can block the
route sections following the next turn.Traffic jam menu1Length of the blocked route section in
miles

Turn the right-hand rotary/push-
button v to highlight “Traffic Jam
Ahead...” in the main detour menu and
press to confirm.
The traffic jam menu will appear.Entering the length of the blocked route
section
Increasing the blocked section

Turn the right-hand rotary/push-
button v to the right.
Decreasing the blocked section

Turn the right-hand rotary/push-
button v to the left.
Calculating detour

Press the right-hand rotary/push-
button v.
The route will be re-calculated. An in-
formation menu will appear.
After that COMAND continues route
guidance.
iCOMAND suggests reasonable route
sections.
Minimum/maximum length of detour is
governed by the logical grouping of rou-
te sections. If additional detour seg-
ments are required after the original
detour, they must be requested indivi-
dually.
iYou can also select “Traffic Jam Ahead”
during the course of a detour. The cur-
rent detour will then be cancelled.

165 Navigation
Route guidance
Detour in route list
Turn the right-hand rotary/push-
button v to highlight “Detour in Route
List” in the main detour menu and
press to confirm.
The message “The route list is being
calculated” will appear.
Then the route list will appear.
Route list1Street cannot be blocked off
2Symbol “+”: street contains several
sections which can be blocked off
3Blocked street will appear in redDisplaying an entry in full in a window

Press u.

Press u again to remove the window.

166 NavigationRoute guidanceCalling detailed route list Detailed route list4Symbol “-” - sections of a road are dis-
played
Press +.
The detailed route list will appear.Blocking off several streets/street sec-
tions

Turn the right-hand rotary/push-
button v to the right.
With each turn, you will block another
section.
The road name will appear in red.
Undoing street block

Turn the right-hand rotary/push-
button v to the left.
The street name will appear in black
again.
Switching back to the route list

Press ,.
The symbol “+” appears in front of the
street section.
The blocking function is still active.Canceling blocking function, do not recal-
culate the route

Press *.
The traffic jam menu will appear.
Ending the blocking function, re-calcula-
ting the route with the blocks selected

Press the right-hand rotary/push-
button v.
COMAND re-calculates the route in the
previously selected calculation mode.
A corresponding message will appear.
Then the symbol display will appear
again and COMAND will continue route
guidance.

187 Info Services/System settings
System settings

System settings
Main system settings menu1Date and time
You can select the time format
(
page 196)
2Adjusts the brightness
3Activates “Settings” menu
4Switches an auxiliary audio source on
(page 200)
5Country setting, with a time zone
(page 192)

Press (.
The main service menu will appear.

Turn the right-hand rotary/push-
button v to highlight “System Set-
tings” and press to confirm.
The main system settings menu will ap-
pear.
1Previous settings
2Current settings

Press the right-hand rotary/push-
button v to confirm “Brightness”.
The “Brightness” menu will appear.
Activating the main settings menu
iYou will see information 5 if the clock
has been set to GPS reception and if a
country, e.g. USA and a time zone was
selected.
Adjusting the brightness
P82.85-7710-31
2
1

190 Info Services/System settingsSystem settingsYou can select the following languages
“Adopt from Instrument Cluster”
COMAND will use the same language
as is set in instrument cluster

“Deutsch”

“English” (metric)
Distance measured in km,
speed in km/h

“English” (imperial)
Distance measured in yards and miles,
speed in miles per hour (mph)

“Español”

“Français”

“Italiano”

“Nederlands”COMAND is equipped with an integrated
clock, which it shows in the main system
settings menu.
Automatically
COMAND automatically sets date and time
if the GPS time is received.
However, you can make the following ad-
justments:
Set the time in increments of 30 minu-
tes (
page 191)

Set the time by selecting a country and
the time zone (
page 192)Manually
You must always set the clock manually
(
page 195), if

COMAND does not receive a GPS time

the clock has been disconnected from
the vehicle battery

the dates of the change between sum-
mer and winter time are not available
Setting date and timeiThe clock displays e.g. the estimated
time of arrival at the destination during
route guidance.

191 Info Services/System settings
System settings
Setting the time in increments of 30 mi-
nutes
You can set the time to any local time (time
zone) in increments of 30 minutes.
1COMAND receives GPS time
2Setting the clock (increments of 30 mi-
nutes)
3Selecting the country and the time
zone (
page 192)
4Selecting the time format (
page 196)

Turn the right-hand rotary/push-
button v to highlight “Date/Time...”
in the settings menu and press to con-
firm.
The menu displays the date and the
time, minutes are highlighted.Activating the setting mode

Press the right-hand rotary/push-
button v.
Setting mode is active, the minutes will
appear in red.
P82.85-7714-312
3
41
P82.85-7715-31

192 Info Services/System settingsSystem settingsAltering the time
Setting the clock ahead
Turn the right-hand rotary/push-
button v to the right.
Each click will move the time 30 mi-
nutes ahead.

Setting the clock back
Turn the right-hand rotary/push-
button v to the left.
Each click will move the time 30 mi-
nutes back.
Canceling setting mode

Press the right-hand rotary/push-
button v.
The minutes appear in black lettering.Switching back to the main system set-
tings menu

Press
*
.
or

Press the right-hand rotary/push-
button v longer than 2 seconds.
You will see the new time.
Selecting the country and the time
zone
You can select among several countries. If
a country has multiple time zones, e.g. Ca-
nada and USA, you can select the applica-
ble time zone.
COMAND will indicate this information in
the main system settings menu.
1Input line
2Activates country list