key MERCEDES-BENZ SL-Class 2003 R230 Comand Manual

107 Telephone
Emergency call
If there is an active Tele Aid call, the tele-
phone main menu will disappear and you
will see the message “Phone off”.
After the Tele Aid call is ended, the tele-
phone main menu will reappear.
See your vehicle’s operator’s manual.Initiating an emergency call
If the telephone main menu or a memory
menu is displayed:

Press number key 1 longer than 2 se-
conds (quick-dialing).
The telephone begins dialing, the “End”
button is highlighted.
When the call is initiated, the call time
will appear.
Do not place the emergency call

Turn the right-hand rotary/push-
button v to highlight the “End” button
and press to confirm or press *.
Ending the call, use one of the three ways:

Press the right-hand rotary/push-
button v to confirm the “End” button.
or

Press a.
or

Press *.
P82.85-9154-31
Telephone is ready for operationiPlease ensure that the number stored in
the memory location is the number you
want to dial in case of an emergency
(default is 9-1-1).
The function will also be performed if
the telephone is locked.
P82.85-9155-31

109 Telephone
Service numbers

Turn the right-hand rotary/push-
button v to highlight “Change 1” in
the “Service No.” menu and press to
confirm.
The “Change Service No. 1” menu will
appear.

Enter the new service number with
number keys 1 through 0.

Press the right-hand rotary/push-
button v to confirm the service num-
ber.
The new service number is now stored
in the “Service No.” menu.
Returning to the menu “Service No.”
The menu “Service No.” will appear auto-
matically after 7 seconds
or

Press *.
Changing personal service number
P82.85-9157-31
iPressing the right-hand rotary/push-
button v and inserting an empty input
line will delete the personal service
number.

132 NavigationDestination inputContinuing destination input via the
mapMap with crosshairs5Street name or name of the symbol
(e.g. parking area) that the cross hairs
are centered on
6Crosshairs to select the destination
7Symbol for current vehicle location
8Current map scale

Turn the right-hand rotary/push-
button v to highlight “Map” and press
to confirm.
The map with the crosshairs will ap-
pear.Moving the crosshairs

Use the number keys (refer also to the
arrows shown on the keypad) to move
the crosshairs around the map.
1 to the top left
2 up
3 to the top right
4 to the left
6 to the right
7 to the bottom left
8 down
9 to the bottom right
iDuring destination input, the map will
always appear facing north (north is on
top).
The map content depends on the map
scale selected.

133 Navigation
Destination input
Altering the map scale
9Current map scale
aScale selector
bNew map scale (filled arrow)
cSquare shows the map section which is
to be increasedActivating the scale selector a.

Press + or ,.
or

Press the right-hand rotary/push-
button v.
iAs you move the crosshairs towards the
edge of the screen using the number
keys, an adjacent section of the map is
activated. It may take a few seconds to
point to each new map.
Adjacent map sections overlap some-
what so that destinations on the edge of
the map can be marked as well.
iA division mark corresponds to an avai-
lable scale. You can select 13 different
scales ranging from 0.05 miles/inch to
500 miles/inch.

135 Navigation
Destination input
Destination entry via coordinates
You can enter a destination if the corres-
ponding coordinates are known.“Coordinate Destination” menu
Turn the right-hand rotary/push-
button v to highlight “Coordinate Des-
tination...” in the Destination via Map
menu (
page 131) and press to con-
firm.
The “Coordinate Destination” input
menu will appear.Activating the adjustment mode

Press the right-hand rotary/push-
button v.
The entry will appear in red.
Altering the setting

Turn the right-hand rotary/push-
button v.
or

Enter cordinates with the number keys.
Storing the new setting and move the mar-
king to the next entry

Press the right-hand rotary/push-
buttonv.
The entry will appear in black.

Subsequently repeat operating se-
quence and enter coordinates comple-
tely.Changing between western (W) and eas-
tern (E) longitude

Press u repeatedly.
Changing between northern (N) and
southern (S) latitude

Press t repeatedly.iAdjustment range
Longitude (W - West or E - East)
0-179° 0-59 min
0-59 s 0.1-0.9 s

Latitude (N - North or S - South)
0-89° 0-59 min
0-59 s 0.1-0.9 s

153 Navigation
Route guidance
If an audio source is switched on, e.g. the
radio, the voice output will be mixed with
that of the audio source.
You can individually set the audio volume
differential between voice output/audio
source (
page 64). COMAND mutes navi-
gation voice outputs during telephone/
Tele Aid operation.
Repeating current voice output

Press the left-hand rotary/push-
button v briefly.
Muting current voice output

Press Ö briefly during a voice out-
put. You will hear the next announce-
ment normally.Switching the voice output off for the
duration of the current route guidance

Press Ö longer than 2 seconds du-
ring a voice output.
You will see the message “Voice output
is muted”.
Switching the voice output on again
The current route guidance has been com-
pleted
Voice output will automatically switch on
again.
During route guidance

Press the left-hand rotary/push-
button v.Altering the voice output volume
At the COMAND control unit

Turn the left-hand rotary/push-
button v during a voice output.
COMAND will accept this setting for
following voice outputs.
At the multifunctional steering wheel
You can alter the volume with the steering
wheel keys during a voice output as well.
To raise the volume:

Press J.
To lower the volume:

Press I.

171 Navigation
Route guidance
During route guidance (you see either sym-
bol or map display) you can select another
COMAND system by pressing the corres-
ponding key.
The main menu of the selected audio sour-
ce will appear and you will e.g. hear the
radio.
Route guidance and the navigation’s voice
output remain active.
The voice output is added to the audio
playback.
You can individually adjust the volume le-
vels for voice output and audio playback
(page 64).

Press c.
The main radio menu will appear. The
station last tuned to will begin to play.

Selecting a station (
page 30).
Returning to navigation system

Press b.During route guidance, you can operate an
audio source that is active in the back-
ground. Although the options are limited,
you can operate the audio source without
having to fully switch to the corresponding
system.
1A window is shown in the symbol or
map display, providing details about
the active audio source
Activating audio system
P82.85-
9230-31
Activating audio functions

172 NavigationRoute guidanceRemoving the window
This is done automatically after 3 seconds.
or
Press *.
The radio is active

Selecting a memorized station from the
respective memory (FM, AM or WB)
Press number keys 1 through 0.

Performing station seek
Press g or h briefly.

Starting manual search
Press g or h longer than
2 seconds.
The search run will start in the desi-
red direction - frequency ranges
FM, AM or WB.CD mode is active

Select CD with number keys
0 CD drive
1 - 6 CD changer

Selecting previous/next track
Press g or h briefly.

Skip backwards/forwards
Hold g or h longer than
2 seconds.

209 Index
selecting 142
Short route 141
Route guidance
advance notice of right turn 154
arriving at destination 170
beginning 152
beginning (way point) 161
canceling 173
changing to the map display 156
deviating from the calculated route
168
following the course of the road 155
Mix of map and symbol display 157
retrieving a destination 174
turning onto a street 154
S
Saving
current destination 175
current vehicle location 177
Radio station 34, 36
Screen displays 9Selecting
City center 130
Destination via the map 131
Service number
changing number for roadside
assistance 110
changing personal service
number 109
Service numbers 108
calling 108
Service sources 63
Setting
Date and time 190
automatically 190
date and time
manually 190
Settings
Brightness (system) 187
Factory settings 199
SMS 103
deleting 105
Incoming SMS message 9Sound 63
Setting Bass/Treble/Balance 65
Sound impressions 66
Sound-center
Balance 64
Speed dialing (only with COMAND) 95
Station
Radio station
Automatic station scan 33
Manual tuning 31
Seek tuning 30
selecting 30
Station selection via direct frequen-
cy entry 32
Station selection via number key-
pad (presets) 32
Station frequency 28
Storing
in the phone book 102
Notebook input 97
Street list 127
Switch on
Radio operation 28