MERCEDES-BENZ SL-Class 2008 R230 Comand Manual

151
Navigation
Route guidance

Route guidance
Route guidance can be started if the
destination input is complete and Start
Route Guidance is displayed at the bottom
of the main area.
Press E.
Route calculation and route guidance
begins. Route calculation can take some time,
depending on the distance to the
destination.
During route calculation,
CALC RTE and an
arrow pointing towards the destination are
displayed.
Route guidance begins when route
calculation is complete.
The system will calculate a new route
during active route guidance if the driver
does not follow the route guidance.
NEW RTE is displayed during recalculation.
The arrow is not filled out. After route calculation, the system assists
route guidance using pictorial displays
(page 152) and voice instructions.
Repeating current voice instructions
If you have not understood a navigation
announcement, you can at any time have a
current announcement repeated.
Press j.
The current navigation announcement
is repeated.
Starting route guidance Route calculation
Recalculating an existing route
Voice instructions
WarningG
Voice instructions are in tended to direct you
while driving without diverting your attenti-
on from the road and driving.
Always use this feature instead of consulting
the map display for directions. Consulting
the map displays for directions may cause
you to divert your attention from driving and
increase the risk of an accident.

152 Navigation
Route guidance
Muting current voice instructions
Press J.
The current announcement is stopped.
You will hear the next navigation
announcement normally.
Switching voice instructions On/Off
Switching off
During a navigation announcement
press J for 2 seconds.
You will hear a confirmation beep if the
beep tones option was activated in the
system settings (
page 217).
The message
Voice Announcements
Muted
will appear briefly. Further route
guidance takes place using only the
symbols in the display. If a new route
guidance cycle is started, the
announcements are automatically
switched on again.
Switching on again
Press j. The navigation displays are only visible
while route guidance is active.
To switch to the navigation display from
another display, e.g.
from CD operation:
Press b or c .
Two examples are shown below:
Display example 1: The road you are currently driving on is
shown on the status bar, in this case
I-90.
The indication
120 mi is the distance to
the next driving maneuver.
If the GPS position display (
page 170) is
active, the GPS data are shown instead of
the street name.
Navigation displays
i
Using the multifunction steering wheel
buttons, the display unit can be
changed between km or miles (see
your vehicle’s Operator’s Manual).
When the display unit is set to
miles, the COMAND will indicate
distances in miles (mi) or feet (ft).
When the display unit is set to km,
the COMAND will indicate
distances in kilometers (km) or
meters (m).

153
Navigation
Route guidance
Important map symbols:
Current vehicle location and direction
of travel
y
If the map orientation
2D Heading Up
(page 169) is chosen, the arrow will
always point upward.
The remaining route section is
highlighted in blue color.
Display example 2: On the right side of the display, the symbol
for the next driving maneuver is indicated
(here: right turn).
On the very right side next to turn symbol
is the distance bar. It indicates the
distance to the next driving maneuver
(here: 300 ft).
The status bar shows the name of the
street after the driving maneuver, if
available, here:
PARK AVE
The destination is marked with a flag
$ on
the map, an intermediate destination is
marked with a flag showing the letter
S.
Altering the map scale
The current map scale is indicated on the
left side of the status bar.
Press any soft key.
The soft key displays appear.
i
The colored highlight only appears
when the system has completed the
route calculation.
i
Using the multifunction steering wheel
buttons, the display unit can be
changed between km or miles (see
your vehicle’s Operator’s Manual).
When the display unit is set to
miles, the COMAND will indicate
distances in miles (mi) or feet (ft).
When the display unit is set to km,
the COMAND will indicate
distances in kilometers (km) or
meters (m).
i
If no other action is taken within
approx. 8 seconds, the soft key
displays will disappear again.

154 Navigation
Route guidance
Press the + or ) soft key.
The map section is zoomed in or
zoomed out. A bar indicating the map
scale appears on the status bar.
Selecting map orientation
A symbol is shown on the bottom left side
of the status bar.
2D North Up Y :
Map is displayed facing north
or
2D Heading Up < :
Dynamic map alignment, map is
displayed facing driving direction
pointing up You can select the map orientation
(
page 169).
Changing the map display
While route guidance is active, you can
switch between split view and full view.
Split view:
The map is shown on the left side and
information on the next maneuver on
the right.
or
Full view:
Full view of the map
Press c.
The display changes with every push of
the button.
i
If GPS display (page 170) is active,
information on your current position is
shown on the status bar.

155
Navigation
Route guidance
If the destination is within a partially
digitized area
COMAND guides you through fully digitized
areas for as long as possible. Route
guidance is conducted in the usual
manner, i.e. with
navigation announce-
ments and route guidance displays.
Before the vehicle reaches a partially
digitized area, COMAND notifies you of
this with the following announcements:
“Be prepared to enter an area where
turn by turn guidance cannot be
provided.”
“In 700 feet you will enter an area
where turn by turn guidance cannot be
provided.”
Partially digitized areas
i
The digital map may contain areas that
are only partially digitized although
they are within a digitized region.
WarningG
Due to incomplete di gitization, the route
shown on the map may differ from the actual
road/traffic situation.
If you follow the route shown on the map, for
example, it is possible that you could drive
the wrong way down a one-way street, that
a street cannot be driven on or that the road
is of questionable quality.
When using route guidan ce on a unverified
road in a partially digitized area, you must
therefore be sure to observe all relevant
traffic regulations an d the course of the
road.
Drive carefully and keep in mind that all re-
levant traffic regulations and the course of
the road always take priority over the route
shown on the map.
i
The indicated distance can be seen
here by way of example. In reality, it
may be different.

156 Navigation
Route guidance
“You are about to enter an area where
turn by turn guidance cannot be
provided.”
Route guidance within a partially
digitized area
If you start route guidance in this type of
area, you will hear the following
announcements:
“You are currently in an area where
turn by turn guidance cannot be
provided.”
“Please follow the arrow on the
display.” Route guidance is provided by means of a
direction arrow showing the compass
heading to the destination. COMAND will
not generate automatic navigation
announcements.
If you try to repeat the current voice
instruction manually, (
page 151) you will
hear the announcement “You are currently
in an area where turn by turn guidance
cannot be provided.”.
During route guidance, the display is
divided. On the right-hand side you will see
the direction arrow showing the compass
heading to the destination.
On the left-hand side of the display you will
see the map with the suggested route. The
suggested route is highlighted blue.
However, it may not be possible to follow
the suggested route because, for example,
the road is closed or not open for car
traffic. 1
Current vehicle location and direction
of travel y
2 Arrow indicates the direction of the
destination and the distance to
destination
If, during route guidance, COMAND leads
you back into a fully digitalized area, route
guidance will simply continue in the usual
manner.
i
When you call up the route info to this
type of destination, (
page 160) the
following data shown there may differ
from the actual situation:
Estimated time of arrival
Distance to the destination

157
Navigation
Route guidance
Route guidance to an off-road destina-
tion
COMAND can guide you to destinations
within the area covered by the digital map,
even if a destination is not located at a
road known to the system.
These destinations are shown as off-road
destinations, which you can enter using
the map, for example.
In these cases, COMAND guides you for as
long as possible with navigation announce-
ments and displays on roads known to the
system.
Shortly before you reach the last known
point in the digitized road network, you will
hear the announcement “The destination
is nearby. Follow the arrow on the display”.
You will then see an arrow that indicates
the direction to the off-road destination.
When the off-road destination is close to
the road, “Area of dest. reached” appears
in addition below the arrow. The section of the route from the last
known point on the map to the off-road
destination is highlighted blue. It simply
shows the direction to the off-road
destination without taking into account
any type of obstacles in the way.
1 Current vehicle position, the triangle
indicates the vehicle’s direction of
travel
2 Off-road section of the route
3 Off-road destination
4 Direction arrow, shows compass
heading to destination, the distance to
destination and
OFF ROAD indication
Off-road and off-map
WarningG
The COMAND navigation system may direct
you to off-road routes that your vehicle may
not be capable of trav ersing through without
damaging your tires, wheels or vehicle. It is
the driver's sole responsibility to determine
the suitability of the ro ute. Off-road routes
may be of varying cond itions and their ap-
propriateness for use may be affected by va-
rious factors such as time of day, time of
year and immediate weather conditions that
cannot be judged or taken into considerati-
on by the COMAND system.

158 Navigation
Route guidance
On the off-road section of the route, direc-
tion arrows showing the compass heading
to the destination guide you. You will also
see the “Direction to destination” display.
Route guidance from an off-road
location to a destination
If there is no road available on map at cur-
rent position of the car, vehicle is off road.
COMAND is also able to guide you to a des-
tination from such a location.
At the start of the route guidance, you will
see the “Off Road” message and a direc-
tion arrow. The direction arrow shows the
compass heading to the actual destina-
tion.
The route is highlighted blue from the
nearest road known to the system.
As soon as the vehicle is back on a road
known to the system, route guidance con-
tinues in the usual way.Route guidance from an off-map
location to a destination
If the vehicle position is outside the area
covered by the digital map, then the vehi-
cle is in an off-map location.
COMAND is also able to guide you to a des-
tination from such a location.
At the start of the route guidance, you will
see the “Off Map” message and a direction
arrow. The direction arrow shows the com-
pass heading to the actual destination.
The route is highlighted blue from the near-
est road known to the system.
As soon as the vehicle is back on a road
known to the system, route guidance con-
tinues in the usual way.
Off-road during route guidance
The road layout may differ from the data on
the digital map, due to road construction
measures, for example.
In such cases, the system cannot allocate
the vehicle’s position to the digital map
and the vehicle is therefore in an off-road
position.
The “Off Road” message and an arrow
showing the compass heading to the
destination appear on the display.
As soon as the system can allocate the
vehicle position’s to the map again, route
guidance continues in the usual way.

159
Navigation
Route guidance
When you reach the destination, you will
see the destination fl
ag. Route guidance
ends.
In navigation mode, press b.
The inquiry menu
Cancel Current
Route Guidance?
will appear.
Press E and confirm with Yes.
Route guidance is cancelled. The
Navigation main menu appears after a
brief delay. Continuing route guidance
Press
h to select No.
Press E.
Arriving at destinationCancelling route guidance
i
You can continue route guidance from
the Navigation main menu
(
page 130).

160 Navigation
During route guidance

During route guidance
During route guidance you can use the soft
keys to activate additional menus and
displays and make settings.
The soft key displays will automatically
disappear after a few seconds.
During route guidance, press any soft
key.
The soft key displays will appear. Available soft keys
Info soft key:
Brings you to the Info menu.
St-over soft key:
Brings you to the stopover destination
function (
page 165).
Detour soft key:
Brings you to the Traffic Jam function
(
page 163).
Memory soft key:
Brings you to the save current location
function (
page 167).
Display soft key:
Brings you to the Display menu
(
page 167).
Soft key +:
Enlarge visible map section.
Soft key ):
Reduce visible map section.
Coord. soft key:
Brings you to the destination
coordinates input (
page 149).
Display the soft keys.
Press the Info soft key.
The Info menu will appear.
1 Your destination with estimated time of
arrival and the remaining distance
2 A stopover destination, if entered
(
page 165)
Displaying the soft keys
Info menu