ESP MERCEDES-BENZ SL-Class 2008 R230 Comand Manual

Welcome to COMAND!Please make yourself familiar with your
COMAND control unit and read the instruc
-
tions in this manual before operating the
COMAND system. This will help you derive
a greater benefit from the system. Please
also follow the instructions and warnings
contained in this manual. Ignoring them
could result in damage to the vehicle or
personal injury to you or others. The asterisk* identifies optional equip
-
ment. Depending on model, version and
configuration, your COMAND system
equipment may differ. Therefore, you may
find explanations for optional equipment
not installed in your vehicle. If you have
any questions about the operation of any
equipment, your authorized Mercedes-
Benz Center will be glad to demonstrate
the proper procedures.
We continuously strive to improve our pro
-
duct and ask for your understanding that
we reserve the right to make changes in
design and equipment. Therefore, informa
-
tion, illustrations and descriptions in this
manual might differ from the equipment in
-
stalled in your vehicle. As such, the infor
-
mation, illustrations and descriptions
contained in this manual may not be reaso
-
nably relied upon in making any claims
with respect to the actual performance of
the product. These operating instructions form an inte
-
gral part of the vehicle and should there
-
fore always be kept inside the vehicle and
passed on to the new owner if the vehicle
is sold. We extend our best wishes for many miles
of safe, pleasurable driving.Mercedes-Benz USA, LLCA DaimlerChrysler Company

9 Introduction
Operating safety


Operating
safety
Warning
G
Any alterations made to electronic compo-
nents and the software can cause malfunc
-
tions.The radio, amplifier, CD changer, satellite ra
-
dio, telephone*, navigation module and
voice control system* are interconnected.
When one of the components is not operati
-
onal or has not been removed/replaced pro
-
perly, the function of other components may
be impaired. This condition might seriously impair the
operating safety of your vehicle.We recommend that you have any service
work on electronic components carried out
only by qualified personnel.
Warning
G
In order to avoid distraction which could
lead to an accident, the driver should enter
system settings with the vehicle at a stand
-
still and operate the system only when road
and traffic conditions permit. Bear in mind that at a speed of just

30 mp/h (approximately 50 km/h),
your car
is covering a distance of 44 feet (approxima
-
tely 14 m) every second.COMAND supplies you with information to
help you select your route more easily and
guide you conveniently and safely to your
destination. For safety reasons, we encoura
-
ge the driver to stop the vehicle in a safe
place before answering or placing a call, or
consulting the COMAND screen to read na
-
vigational maps, instructions, or downloa
-
ded information.
While the navigation system provides direc
-
tional assistance, the driver must remain fo
-
cused on safe driving behavior, including
attention to traffic and street signs, and
should utilize the system’s audio cues while
driving. The navigation system does not supply any
information on stop signs, yield signs, traffic
regulations or traffic safety rules. This al
-
ways remains your personal responsibility
when you drive. DVD maps do not cover all
areas nor all routes within an area.

29 At a glance
Multifunction steering wheel

Switch the multifunction display to the
respective system if you wish to
operate the system using the buttons
on the multifunction steering wheel.

On the multifunction steering wheel,
press è or ÿ repeatedly until
one of the following, Radio, Single CD
or MP3 CD, CD changer, Satellite radio
or Telephone* display appears in the
multifunction display of the instrument
cluster.
Radio operation1Waveband2Station frequency
Weather Band operation1Weather Band (WB)2Channel nameSingle CD operation1CD mode2Current track
CD changer operation1CD changer mode2Current trackMP3 CD operation1MP3 mode2Current track
Selecting the multifunction display

39 At a glance
Quick reference COMAND
In Radio, CD, CDC, MP3-CD, DVD or
satellite radio operation:
Activate the main menu for the
respective operating mode ( page
31)
.

Press the
Sound
soft key.
The Sound menu appears.

Press g or G to select the desired
function.

Press E.The function is activated.

45
Audio
Radio operation
You can use the following functions:
Automatic seek tuning (page 45)
Manual tuning (page 45)
Station selection from the Preset menu
(
page 45)
Station selection via direct frequency
entry (FM, AM) (
page 47)
Automatic station scan (FM, AM)
(
page 47)
Station selection from the FM/AM
Autostore presets (
page 51)
Automatic seek tuning
Press
g or h .
or
Press g or G .
FM and AM Bands, Weather Band (WB)
The radio will tune in to the next receivable
station (FM, AM) or channel (WB) with de-
scending/ascending frequency depending
on the direction of seek.
WB
Alternatively, you can select the channel
directly:
Press a number key 1 through 7. Manual tuning (FM, AM)
Activate the desired wave band
(
page 43).
Press
g or h longer than 2 se-
conds.
The function is active.
or
Press H or h .
The frequency will change by the tuning
increments for the respective
waveband each time one of the buttons
is pressed.
FM Band
The frequency displayed will change in in-
crements of 0.2 MHz.
AM Band
Tuning will take place in increments of
10 kHz.
Selecting a station
i
The selected channel is not shown in
the status line.

46 Audio
Radio operation
Station selection via number keypad
(presets)
FM and AM Bands
Press one of the number keys, such as
2 briefly.
The radio will tune to the frequency as-
signed to that memory location. If none
has been set by you, the radio will not
change the station. Station selection vi
a direct frequency
entry (FM, AM)
E.g.: 102.7 MHz in the FM bandActivate the desired waveband
(
page 43).
Press *.
An input line will appear.
Enter the desired frequency with the
number keys within 8 seconds, e.g.
1027 for 102.7 FM.
The station you have selected will
begin to play.
i
FM and AM preset s are independent
and can only be accessed while in the
corresponding band.
Saving stations for FM and AM
(
page 48).
Frequency bandFrequency range
FM
AM87.7 - 107.9 FM
530 - 1710 AM

50 Audio
Radio operation
Selecting a station from the preset
menu (FM, AM)
Activate the FM or AM memory
(
page 48).
You can use one of the following two ways
to select a station from the FM/AM
presets
Press the corresponding number key,
e.g. 3, to select the desired station.
or
Use H, h or g , G to highlight a
memory preset in the FM/AM preset
list.
Press E.
In both cases, you will see the Radio
main menu
automatically after 8 seconds
if you press the Back soft key.
The Radio main menu indicating the
memory preset number appears.

52 Audio
CD operation

CD operation
General Information on CD operation
WarningG
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and
operate the audio system only if permitted
by road, weather and traffic conditions.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car covers a
distance of 44 feet (approximately 14 m)
every second.
WarningG
The CD drive and CD changer are Class 1 la-
ser products. There is a danger of invisible
laser radiation when you open or damage
the cover.
Do not remove the cover. The CD drive and
the CD changer do not contain any parts
which can be serviced by the user. For safe-
ty reasons, have any necessary service work
performed by qua lified personnel.
i
Only use CDs, which bear the label
shown and that conform to the compact
standard (IEC 60908). You can there-
fore only use CDs with a maximum
thickness of 1.3 mm.
i
The COMAND CD drive may not be able
to play audio CDs with copy protection
or copied CDs.
!
Use only CDs with a diameter of 12 cm,
do not use 8-cm CDs.
An 8-cm CD adapter may cause dama-
ge to the CD changer or to the
COMAND and should not be used.
i
Your CD drive has been designed to
play CDs which correspond to the IEC
60908 standard.
If you insert thicker data carriers, e.g.
ones that have data on both sides (one
side with DVD data, the other side with
audio data), they cannot be ejected
and will damage the drive.

58 Audio
CD operation
You can select a audio or MP3-CD:
in the CD list (page 58)
with the number keypad (page 58)
in the Magazine menu (page 58)
In the CD list
The CD list includes all loaded CDs. Only
one list entry is visible at a time.
The entry is displayed above the track
indication. It shows the number or the
name of the CD currently playing.
Use h or H to select another CD
from the list.
After the CD is loaded, it is played
back.
or
Do not change the selection.
Playback of the last played CD is
continued.
With the number keypad
Press a number key, e.g. 2 to select
the corresponding CD.
The CD is changed. The selected CD is
played back. In the Magazine menu
Press the CD-Mag soft key.
The Magazine menu is displayed. If the
magazine has not been read in, the
message
Magazine Scan
Please Wait
is displayed first.
Use g or G to select a CD.
Press E.
or
Press one of the number keys 1 to
6 .
The CD is changed.
Selecting a CD (CD changer only)
i
Selection is possible if the
CD changer has loaded the magazine
and at least two audio or MP3-CDs are
loaded.
i
The number keys 1 - 6 can be used
for direct selection.
Keys 1 - 6 correspond with
magazine slots 1 to 6
of the CD changer

63
Audio
MP3-CD operation

MP3-CD operation
General Information
WarningG
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and
operate the audio system only if permitted
by road, weather and traffic conditions.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your car covers a
distance of 44 feet (approximately 14 m)
every second.
WarningG
The CD drive and CD changer are Class 1 la-
ser products. There is a danger of invisible
laser radiation when you open or damage
the cover.
Do not remove the cover. The CD drive and
the CD changer do not contain any parts
which can be serviced by the user. For safe-
ty reasons, have any necessary service work
performed by qualified personnel.
!
Your CD drive has been designed to
play CDs which correspond to the IEC
60908 standard. Therefore only CDs
not exceeding a thic kness of 1.3 mm
can be used.
The smallest possible data rate for
MP3-CDs is 56 kB/s.
The COMAND does not play back
MP3-CDs containing files with ISO
9660 Level 3 standard. Such MP3 CDs
contain fragmented files.