clock MERCEDES-BENZ SL CLASS 2020 User Guide

!
Have
thebattery regularlychecked ata
qual ified speciali stworkshop.
Comply withtheservice intervals inthe
Maintenance Booklet,orcont actaqual ified
speciali stworkshop formore information.
! Alway
shave work onbatteries carriedout
at aqual ified speciali stworkshop.
Should it,inexceptional circumstances, be
absolu telynecessary todisconnect the12-
volt battery yourself,please observe thefol-
lowing:
R Secure thevehicle toprevent itfrom roll-
ing awa y.
R Switch offthe ignition.
R Disconn ectthe negative terminalfirstand
then thepositive terminal.
After thework hasbeen done, install the
battery andreplace thecover ofthe positive
terminal clampfirmly.
Comply withsafety precautions andtake pro-
tect ivemeasures whenhandling batteries. Risk
ofexplosion. Fire,
open flames andsmoking are
prohibited whenhandling thebat-
tery. Avoid creating sparks. Battery
acidiscaustic. Avoidcon-
tact with skin, eyesorclothing.
Wear suitabl eprotective clothing,
especial lygloves, apronandface-
guard.
Rinse anyacid spills immediately
with clear water. Contact aphysi-
cian ifnecessary. Wear
eyeprotection. Keep
children away. Observe
thisOperator's Manual.
For safety reasons, Mercedes-Benz recom-
mends thatyouonly usebatteries whichhave been
tested andapproved foryour vehicle by
Mercedes-Benz .These batteries provide
increased impactprotection toprevent vehicle
occupants fromsuffering acidburns should
the battery bedamage din the event ofan
accident.
In order forthe battery toachieve themaxi-
mum possible servicelife,itmust alwaysbe
sufficiently charged.
Like other batteries, thevehicle battery may
discharge overtime ifyou donot use thevehi-
cle. Inthis case, havethebattery disconnec-
ted ataqual ified speciali stworkshop. Youcan
also charge thebattery withacharger recom-
mended byMercedes-Benz .Contact aqual i-
fied speciali stworkshop forfurther informa-
tion.
Have thebattery condition ofcharge checked
more frequently ifyou usethevehicle mainly
for short tripsorifyou leave itstanding idle
for alengthy period.Consult aqual ified spe-
cialist workshop ifyou wish toleave yourvehi-
cle parked foralong period oftime.
Remove theSmartKey ifyou park thevehicle
and donot require anyelectrical consumers.
The vehicle willthen usevery little energy,
thus conserving batterypower.
After aninterruption tothe power supply,e.g.
due toadischarged battery,youmust reset
the clock (seetheDigital Operator's Manual). Charging
thebattery G
WARNING
During charging andjump-startin g,explosive
gases canescape fromthebattery. Thereis
a risk ofan explosion.
Particularl yavoid fire,open flames, creating
sparks andsmoking. Ensurethereissuffi-
cient ventilation whilecharging andjump-
starting. Donot lean over abattery. G
WARNING
Battery acidiscaustic. Thereisarisk of
injury.
Avoid contactwith skin, eyesorclothing. Do
not inhale anybattery gases.Donot lean
over thebattery. Keepchildren awayfrom
batteries. Washawaybattery acidimmedi- Bat
tery (vehic le)
287Breakdown assistance
Z

Make
surethat:
R The jumper cablesarenot damaged.
R Bare parts ofthe terminal clampdonot come intocontactwith other metal partswhile the
jumper cablesareconn ected tothe battery.
R The jumper cablescannot comeintocontactwith parts which canmove whentheengine is
running, suchasthe V-belt pulleyor the fan.
X Secure thevehicle byapply ingthe electric parking brake.
X Shift thetransmission toposition 005D.
X Make surethattheignition isswitched off.Allindicator lampsinthe instrumen tcluster must
be off. When usingtheSmartK ey,turn theSmartK eytoposition 0092inthe ignition lockand
remove it(Y page 126).
X Switch offallelectrical consumers, e.g.rear window defroster, lighting,etc.
X Open thehood. Position
number0084identifies thecharged batteryofthe other vehicle oran equival entjump-
startin gdevice.
X Press cover0043ofpositive terminal 0044down (inthe direction ofthe arrow) andturn itclock-
wise. Toexpose positive terminal 0044,press cover 0043down further.
X Connect positiveterminal 0044onyour vehicle topositive terminal 0087ofdonor battery 0084using
the jumper cable,alwaysbegin withpositive terminal 0044onyour ownvehicle first.
X Start theengine ofthe donor vehicle andrunitat idling speed.
X Connect negative terminal0085ofdonor battery 0084toground point0083ofyour vehicle usingthe
jumper cable,beginning withdonor battery 0084first.
X Start theengine.
X Before disconnec tingthejumper cables,letthe engine runforseveral minutes.
X First, remove thejumper cablesfromground point0083and negative terminal0085,then from
positive terminal 0044and positive terminal 0087.Begin eachtimeatthe cont acts onyour own
vehicle first.
X Aft erthe jumper cableisremoved, returncover0043ofpositive terminal 0044tothe original posi-
tion. Positive terminal 0044iscovered upand thus insulated again.
X Have thebattery checkedataqual ified specialist workshop.
Jump-starting isnot considered tobe anormal operating condition. 290
Jump
-startingBr eakdown assistance

The
bracket sfor the screw-in towingeyeare
located inthe bumpers. Theyareatthe front
and atthe rear, behind thecovers.
X Remove thetowing eyefrom thevehicle tool
kit (Ypage 280).
X Front bumper:insert afinger intothe
recess onthe botto medge ofcover 0043.
X Pull cover 0043out ofthe bumper towards you
in the direction ofthe arrow.
Cover 0043isattached tothe opening witha
strap.
X Rear bump er:press themark oncover 0043
inwards inthe direction ofthe arrow.
X Remove cover0043from theopening.
X Scr ew inthe towing eyeclock wiseasfar as
it will goand tighten it.
Removing thetowing eye X
Unsc rewand remove thetowing eye.
X Front bumper:position cover0043onthe
opening inthe bumper.
X To close, pressthelower section of
cover 0043.
X Rear bump er:position cover0043with the
tab onthe opening inthe bumper.
X To close, pressthelower section of
cover 0043until itengages.
X Place thetowing eyeinthe vehicle toolkit. Towing
avehicle withboth axles on
the ground G
WARNIN
G
You cannolonger steerthevehicle ifthe
steerin gwheel lockhasbeen engaged.
There isarisk ofan accident .
Always switchoffthe ignition whentowing
the vehicle withatow cable oratow bar.
The automatic transmission shiftstoposition
005D automatically whenyouopen thedriver's
or front -passenger doororwhen youremove
the Smart Keyfrom theignition lock.
In order toensure thattheautomatic trans-
mission staysinposition 005Cwhen towing
away thevehicle, youmust observe thefollow-
ing points:
X Switch onthe hazard warning lamps
(Y page 111).
X Make surethatthevehicle isstation aryand
that theSmart Keyisin position 0092inthe
ignition lock.
X Turn theSmart Keytoposition 0048inthe igni-
tion lock.
On vehicles withKEYLE SS-GO, usethe
Smart Keyinstead ofthe Start /Stopbutton
(Y page 126).
X Depress andhold thebrake pedal.
X Shift thetrans mission toposition 005C.
X Release thebrake pedal.
X Release theelectric parking brake.
X Leave theSmart Keyinposition 0048inthe
ignition lock.
In order tosignal achange ofdirection when
towing thevehicle withthehazard warning
lamps switched on,use thecombinat ion
switch asusual. Inthis case, onlytheindicator
lamps forthe direction oftravel flash.When
you reset thecombinat ionswitch, thehazard
warning flashersstartflashing again.
It is important thatyouobserve thesafety
instr uctions whentowing awayyourvehicle
(Y page 291). Permit
tedtowing methods
Mercedes- Benzrecomm endstransportin gyour
vehicle inthe case ofabreakdown, ratherthan
towing itaway . 292
Towing
andtow-sta rtingBr eakdown assistance

R
The jack must beplaced onafirm, flatand
non- slipsurface. Onaloose surface, alarge,
flat, load-bearing underlaymustbeused. On
a slippery surface, anon- slipunderlay must
be used, e.g.rubber mats.
R Do not use wooden blocksorsimilar objects
as ajack underlay. Otherwise, thejack will
not beable toachieve itsload-bearing capa-
city due tothe restr icted height.
R Make surethatthedistance between the
underside ofthe tires andtheground does
not exceed 1.2in(3 cm).
R Never placeyourhands andfeet under the
raised vehicle.
R Do not lieunder thevehicle.
R Do not start theengine whenthevehicle is
raised.
R Do not open orclose adoor orthe trunk lid
when thevehicle israised.
R Make surethatnopersons arepresent in
the vehicle whenthevehicle israised.
Vehicles withalloy wheels andhub caps:
the wheel boltsarecovered byahub cap.
Before youcan unscrew thewheel bolts,you
must remove thehub cap. Twodifferent var-
iants canbeinstalled. X
To remove: takesocket 0044and lugwrench
0087 from thevehicle toolkit(Ypage 280).
X Position socket0044onhub cap0043.
X Position lugwrench 0087onsocket 0044.
X Using lugwrench 0087,turn hubcap0043coun-
ter- clock wiseandremove it.
X To install: beforeinstalling, checkhub
cap 0043and thewheel areaforsoiling and
clean ifnecessary.
X Put hub cap0043inposition andturn until itis
in the right position. X
Position socket0044onhub cap0043.
X Attach lugwrench 0087tosocket 0044and
tighten hubcap0043.
The tighten ingtorque mustbe
18 lb-ft (25Nm).
i Note
thatthehub capshould betight-
ened tothe specified torqueof18 lb-ft
(25 Nm). Mercedes- Benzrecomm endsthat
you have thehub capinstalled ataqualified
specialist workshop. X
Using lugwrench 0087,loosen thebolts on
the wheel youwish tochange byabout one
full turn. Donot unscrew thebolts com-
pletely. The
jackingpoints arelocated justbehind the
front wheel housings andjust infront ofthe
rear wheel housings (arrows).
Mercedes-AMG vehiclesandvehicles with
AMG equipm ent:toprotec tthe vehicle body,
the vehicle hascovers installed nexttothe
jack ingpoints onthe outer sills. 318
Changing
awheelWheels andtires

X
Merce
des-AMGvehic lesand vehic les
with AMG equipment: foldcover 0085
upw ards. X
Posi tion jack 0084atjacking point0083. X
Make surethefoot ofthe jack isdirectly
benea ththe jacking point.
X Turn crank 006Bclockwis euntil jack0084sits
comple telyonjacking point0083.The base of
the jack must lieevenly onthe ground .
X Turn crank 006Buntil thetire israis edamaxi-
mum of1.2 in(3 cm) from theground . Removi
ngawhe el !
Merce
des-AMGvehic les:duri ngremova l
and reposi tioning ofthe whee l,the whee l
rim can strike thecerami c-brake discand
dama geit.Therefo re,you shou ldproceed
carefu llyand getasecond personassistto
you .Alternativel y,you can useasecond
ali gnment bolt.
! Do
not placewhee lbolts insand oron a
dirty surface.The bolt andwhee lhub
threads couldotherwi sebe dama gedwhen
you screw themin. X
Unscrew theuppermost wheelbolt com-
pletel y.
X Screw alignment bolt0043into thethread
instead ofthe whee lbolt.
X Unscrew theremai ningwhee lbolts fully.
X Remo vethe whee l.
Mountin ganew wheel G
WARNING
Oile dor grea sedwhee lbolts ordama ged
whee lbolts/hu bthreads cancaus ethe
whee lbolts tocome loose.As aresul t,you
coul dlose awhee lwhi ledrivi ng.There isa
risk ofaccide nt.
Never oilorgrea sewhee lbolts. Inthe event
of dama getothe threads ,contact aqua li-
fied specia listworkshop immediately.Have
the dama gedwhee lbolts orhub threads
repla ced/renew ed.Donot continue driving. Chang
ingawhe el
319Whee lsand tires Z

G
WARNING
If you tighten thewhee lbolts orwhee lnuts
when thevehicl eis rais ed, the jack couldtip
over. There isarisk ofinjury .
Only tighten thewhee lbolts orwhee lnuts
when thevehicl eis on the grou nd.
Alwa yspay attention tothe instructions and
safety notesinthe "Changi ngawhee l"section
(Y pag e316).
Only usewhee lbolts thathave been designed
for the whee land thevehicl e.For safety rea-
sons, Mercede s-Benzrecommends thatyou
only usewhee lbolts whichhave been
app roved forMercede s-Benzvehiclesand the
respe ctivewheel.
! Merce
des-AMGvehi cles:duri ngremova l
and repos itioning ofthe whee l,the whee l
rim can strike thecerami c-brake discand
dama geit.There fore,youshou ldproceed
carefu llyand getasecond personassi stto
you .Alternativel y,you can useasecond
ali gnment bolt.
! To
prevent damagetothe paintwork, hold
the whee lsecure lyaga inst thewhee lhub
whi lescrewi nginthe first whee lbolt. X
Cle anthe whee land whee lhub contact sur-
faces.
X Slide thewhee lto be mounted ontothe
ali gnment boltandpushit on.
X Tigh tenthewhee lbolts untiltheyarefinger-
tight.
X Unscrew thealignment bolt.
X Tigh tenthelastwhee lbolt until itis finger-
tight. Lo
we ring thevehi cle G
WARNING
The whee lscoul dcome looseif the whee l
bolts orwhee lnuts arenot tightened tothe
prescri bedtightening torque.There isarisk
of an accide nt.
Ensure thatthewhee lbolts orwhee lnuts
are tightened tothe prescri bedtightening
torque .
If you arenot sure ,do not move thevehicl e.
Contact aqua lified speci alist worksho pand
have thetightening torquechecked immedi-
ately .
X Turn thecrank ofthe jack counter-clockwi se
until thevehicl eis once againstanding
firmly onthe grou nd.
X Pla cethe jack toone side. X
Tigh tenthewhee lbolts evenly inacross-
wis epattern inthe sequ ence indica ted(0043
to 0083). Thespeci fiedtightening torqueis
96 lb-ft (130Nm).
X Turn thejack back toits initia lposi tion.
X Stow thejack andtherest ofthe vehicl e
tools inthe trunk again.
X Merce
des-AMGvehic lesand vehic les
with AMG equipment: insertthecover into
the outer sill.
X Che ckthe tire pressu reofthe newly moun-
ted whee land adjustitifnecessa ry.
Observe therecommende dtire pressu re
(Y pag e299) .
Vehic leswith atire pressure control sys-
tem: allinstall edwhee lsmust beequ ipped
with functioning sensors.
When youaredrivi ngwith theemerge ncy
spar ewhee lmounted, thetire pressu remoni- 320
Chang
ingawhe elWhee lsand tires