reset MERCEDES-BENZ SL550 2008 R230 User Guide

137 Controls in detail
Lighting
Switching off corner-illuminating front
fog lamps
The combination switch for the turn signal
resets automatically after major steering
wheel movements. This will switch off the
corner-illuminating front fog lamps if they
were activated by switching on the left or
right turn signal.If the turn signal should stay on after
making the turn, the turn signal and
corner-illuminating front fog lamp can be
switched off by returning the combination
switch to its original position.
Driving in reverse
Switching on corner-illuminating front
fog lampsPlace the gear selector lever in
positionR.
The front fog lamp opposite to your
steering direction comes on.
Switching off corner-illuminating front
fog lamps
Place the gear selector lever out of
positionR.
The respective front fog lamp goes out.
Hazard warning flasher
The hazard warning flasher can be
switched on at all times, even with the
SmartKey removed from the starter switch
or with the SmartKey with KEYLESS-GO*
removed from the vehicle.
The hazard warning flasher switches on
automatically when an air bag deploys.
The hazard warning flasher switch is
located on the upper part of the
center console.
1Hazard warning flasher switchiThe corner-illuminating front fog lamps
temporarily come on both sides of the vehicle
if you turn the steering wheel in one direction
and then again in the other direction shortly
thereafter.
iThe corner-illuminating front fog lamps
will come on automatically depending on the
steering angle, even if you did not switch on
either turn signal.
If the corner-illuminating front fog lamps came
on automatically, they will also go out automati-
cally depending on the steering angle.iThere may be a brief delay before the
corner-illuminating front fog lamps switch off.

140 Controls in detail
Instrument cluster
For a full view illustration of the instrument
cluster, see “Instrument cluster”
(
page 26).
1Reset button
The instrument cluster is activated when
you

open a door

switch on the ignition (page 40)

press reset button 1

switch on the exterior lamps
Opening a door will activate the instrument
cluster only for about 30 seconds.You can change the instrument cluster
settings in the Instrument cluster submenu
of the control system (
page 160).Adjusting instrument cluster
illumination
Use the reset button to adjust the illumina-
tion brightness for the instrument cluster
and the switches on the center console.
To brighten illumination
Turn reset button 1 in the instrument
cluster clockwise.
The instrument cluster illumination will
brighten.
To dim illumination
Turn reset button 1 in the instrument
cluster counterclockwise.
The instrument cluster illumination will
dim.
Warning!G
No messages will be displayed if either the
instrument cluster or the multifunction
display is inoperative.
As a result, you will not be able to see
information about your driving conditions,
such as speed or outside temperature,
warning/indicator lamps,
malfunction/warning messages or the
failure of any systems. Driving characteris-
tics may be impaired.
If you must continue to drive, do so with
added caution. Visit an authorized
Mercedes-Benz Center as soon as possible.iThe instrument cluster illumination is
dimmed or brightened to suit ambient light
conditions.

141 Controls in detail
Instrument cluster
Coolant temperature gaugeResetting trip odometer
Make sure you are viewing the trip
odometer display (
page 143).
If it is not displayed, press the
jork button on the multi-
function steering wheel repeatedly
until the trip odometer appears.
Press and hold reset button1
(
page 140) until the trip odometer is
reset.
Warning!G

Driving when your engine is overheated
can cause some fluids which may have
leaked into the engine compartment to
catch fire. You could be seriously
burned.

Steam from an overheated engine can
cause serious burns which can occur
just by opening the hood. Stay away
from the engine if you see or hear steam
coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!Excessive coolant temperature triggers the
coolant temperature warning lamp (
page 348)
and a warning in the multifunction display
(
page 383).
The engine should not be operated with the cool-
ant temperature above 248°F (120°C). Doing so
may cause serious engine damage which is not
covered by the Mercedes-Benz Limited
Warranty.
iDuring severe operating conditions, e.g.
stop-and-go traffic, the coolant temperature may
rise close to 248°F (120°C).

148 Controls in detail
Control system
Menu 6Menu 7Menu 8Menu 9
Vehicle status
message memory1SettingsTrip computerTelephone*
(page 156)(page 157)(page 167)(page 169)
Commands/submenus
Calling up vehicle
malfunction, warning
and system status
messages stored in
memoryResetting to factory
settingsFuel consumption
statistics since startLoading phone book
Instrument cluster
submenuFuel consumption
statistics since last re-
setSearching for name in
phone book
Time submenuResetting fuel consump-
tion statistics
Lighting submenuDistance to empty
Vehicle submenu
Convenience submenu
1The vehicle status message memory menu is only displayed if there is a message stored.
iThe headings used in the menus table are
designed to facilitate navigation within the system and are not necessarily identical to
those shown in the control system displays.
The first function displayed in each menu willautomatically show you which part of the system
you are in.

152 Controls in detail
Control system
Saving lap time and starting a new lap
Press button ç while the timer is
running.
The intermediate time will be shown for
5 seconds.
Press button ç within the next
5 seconds.
The intermediate time shown will be
saved as a lap time.
The RACETIMER begins timing the new
lap. The new lap begins to be timed as
soon as the intermediate time is called
up.1Best lap time
2Lap number
3RACETIMER
4Gear indicator
Resetting current lap
Press button æ while the timer is
running.
The timer stops.
Press button ç.
The lap time is reset to “0”.Deleting all laps
Press button æ while the timer is
running.
The timer stops.
Press the reset button twice
(
page 27).
Press button æ.
The timer starts. The saved laps are
deleted.
iYou can save up to nine laps.iIt is not possible to delete a single saved lap.
iWhen you switch off the engine, the
RACETIMER will be reset to“0” after 30 seconds.
All laps are deleted.

157 Controls in detail
Control system
If conditions have occurred causing status
messages to be recorded, the number of
messages appears in the right multifunc-
tion display:
1Number of recorded status messages
Press button k or j.
The stored messages will now be dis-
played in the order in which they have
occurred. For malfunction and warning
messages, see “Vehicle status messag-
es in the multifunction display”
(
page 359).Should the vehicle’s system record any
conditions while driving, the number of
messages will reappear in the multifunc-
tion display

when the SmartKey in the starter
switch is turned to position0 or
removed from the starter switch
or

when you turn off the engine by press-
ing the KEYLESS-GO* start/stop
button on the gear selector lever once
and open the driver’s door (this puts
the starter switch in position 0, same
as with the SmartKey removed from
the starter switch)
Settings menu
In the
Settings menu there are two
functions:

The function Reset, with which you can
reset most settings to those set at the
factory.

A collection of submenus with which
you can make individual settings for
your vehicle.
The following settings and submenus are
available:
iAfter you have scrolled through all recorded
status messages, the first recorded message
appears again.
iThe vehicle status message memory will be
cleared when you then turn the SmartKey in the
starter switch to position 1 or 2, or when you
press the KEYLESS-GO* start/stop button once
or twice without depressing the brake pedal. You
will then only see high priority messages in the
multifunction display (
page 359).
FunctionPage
Resetting all settings158
Submenus in the Settings menu158
Instrument cluster submenu160
Time submenu161
Lighting submenu163
Vehicle submenu166
Convenience submenu166

158 Controls in detail
Control system
Resetting all settings
You can reset the functions of most of the
submenus to the factory settings.
For safety, the
Light Circuit Headlamp
Mode
submenu in the Lighting menu can
be reset with the vehicle at standstill only.
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press the reset button in the instru-
ment cluster for approximately
3 seconds.
In the right multifunction display you
will see the request to press the reset
button again to confirm.
Press the reset button again.
The functions of most submenus will
reset to factory settings.
Submenus in the Settings menu
Press button è or ÿ repeatedly
until the
Settings menu appears in the
multifunction display.
Press button j.
In the right multifunction display you
see the collection of submenus. There
are more submenus than can be simul-
taneously displayed.
Press button ç.
The selection marker moves to the next
submenu.
Scroll down with the ç button,
scroll up with the æ button.
With the selection marker on the de-
sired submenu, use the j button to
access the individual functions within
that submenu.
Once within the submenu, use
thej button to move to the next
function or the k button to move to
the previous function within that sub-
menu.
Use buttons æ or ç to change
the settings of the respective function.
iThe settings you have changed will not be
reset unless you confirm the action by pressing
the reset button a second time.

163 Controls in detail
Control system
Lighting submenu
Access the
Lighting submenu via the
Settings menu. Use the Lighting sub-
menu to change the lamp and lighting set-
tings on your vehicle. The following
functions are available:Setting daytime running lamp mode
(USA only)
Move the selection marker with
buttonæ or ç to the
Lighting
submenu.
Press button j or k repeatedly
until the message
Light Circuit
Headlamp Mode
appears in the multi-
function display.
The selection marker is on the current
setting.
Press button æ or ç to select
manual operation (
Manual) or daytime
running lamp mode (
Constant).With daytime running lamp mode activated
and the exterior lamp switch in
positionM or U the low beam head-
lamps are switched on when the engine is
running.
In low ambient light conditions the follow-
ing lamps will switch on additionally:

Parking lamps

Tail lamps

License plate lamps

Side marker lamps
For more information on the daytime run-
ning lamp mode, see “Lighting”
(
page 131).
FunctionPage
Setting daytime running lamp
mode (USA only)163
Setting locator lighting164
Setting night security illumina-
tion164
Setting interior lighting delayed
switch-off 165
iThis function is not available in countries
where the daytime running lamp mode is manda-
tory and therefore in a constant mode.
iFor safety reasons, resetting to factory
settings (
page 158) while driving will not
deactivate the daytime running lamp mode.
The following message appears in the multifunc-
tion display:
Cannot be fully reset to
factory settings while driving.

167 Controls in detail
Control system
Move the selection marker with
theæ orç button to the

Convenience
submenu.
Press button j or k repeatedly
until the message
Easy-entry
Function
appears in the multifunction
display.
The selection marker is on the current
setting.
Press button æ or ç to switch
the easy-entry/exit feature
On or Off.
Trip computer menu
Use the trip computer menu to call up
statistical data on your vehicle.
The following information is available:
Warning!G
You must make sure no one can become
trapped or injured by the moving steering
wheel when the easy-entry/exit feature is
activated.
To stop steering wheel movement, do one of
the following:

Move steering wheel adjustment stalk
(
page 47).

Press one of the memory position
buttons* or the memory button M*
(
page 129).
Do not leave children unattended in the ve-
hicle, or with access to an unlocked vehicle.
Children could open the driver’s door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
FunctionPage
Fuel consumption statistics
since start168
Fuel consumption statistics
since last reset168
Resetting fuel consumption
statistics168
Distance to empty169
iThe last function called up will reappear the
next time you enter the trip computer menu.

168 Controls in detail
Control system
Fuel consumption statistics since start
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
From Start.
1Distance driven since start
2Average speed since start
3Time elapsed since start
4Average fuel consumption since startFuel consumption since last reset
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see this message in the left
multifunction display:
From Reset.
1Distance driven since last reset
2Average speed since last reset
3Time elapsed since last reset
4Average fuel consumption since last
resetResetting fuel consumption statistics
Press button ÿ or è repeatedly
until you see the first function of the
trip computer menu.
Press button j or k repeatedly
until you see the reading that you want
to reset in the left multifunction dis-
play.
Press and hold the reset button in the
instrument cluster (
page 27) until
the value is reset to
0.
iAll statistics stored since the last engine
start will be reset approximately 4 hours after
the SmartKey in the starter switch is turned to
position0 or removed from the starter switch.
Resetting will not occur if you turn the SmartKey
back to position1 or2 within this time period.
iThe fuel consumption statistics reset
automatically to
0 when either of the following
values is exceeded:

distance covered: 100 000 miles

time elapsed: 10 000 hours