sport mode MERCEDES-BENZ SL550 2008 R230 Owner's Manual

95 Safety and Security
Driving safety systems
The electro-hydraulic brake system is auto-
matically activated when you

unlock the vehicle with the SmartKey
or with KEYLESS-GO*

open the driver’s or passenger door

turn the SmartKey in the starter switch
to position1

in vehicles with KEYLESS-GO*, press
the start/stop button on the gear se-
lector lever once

depress the brake pedal

release the parking brake
Warning!G
The electro-hydraulic brake system requires
electrical power to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. In such a case, the
red brake warning lamp (
page 345)
comes on and warning messages
(
page 377) appear in the multifunction
display while driving. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is in-
creased!
If there is a malfunction in the
electro-hydraulic brake system, we recom-
mend that the vehicle be transported with
all wheels off the ground using flatbed or ap-
propriate wheel lift/dolly equipment.
A tow bar must be used if circumstances do
not permit the use of the recommended
towing methods and the vehicle requires
towing with all four wheels on the ground.
Towing the vehicle with all four wheels on
the ground is only permissible for distances
up to 30 miles (50 km) and at a speed not to
exceed 30 mph (50 km/h). For more infor-
mation, see “Towing the vehicle”
(
page 434).

177 Controls in detail
Automatic transmission
The selected gear range appears in the
right multifunction display.
1Current gear rangeAutomatic shift program
The program mode selector switch is
located on the lower part of the center
console.
Program mode selector switch
C Comfort For comfort driving
S Sport For standard driving
Effect
ïThe transmission shifts through
sixth gear only (applies to
vehicles with 7-speed automatic
transmission only).
îThe transmission shifts through
fifth gear only (applies to
vehicles with 7-speed automatic
transmission only).
éThe transmission shifts through
fourth gear only.
Effect
èThe transmission shifts through
third gear only.
With this selection you can use
the braking effect of the engine.
çThe transmission shifts through
second gear only.
Allows the use of engine’s
braking power when driving

on steep downgrades

in mountainous regions

under extreme operating
conditions
æThe transmission operates in
first gear only.
For maximum use of engine’s
braking effect on very steep or
lengthy downgrades.

178 Controls in detail
Automatic transmission
Program mode selector switch
(SL 55 AMG and SL 65 AMG only)
MANUAL For manual gear shifting
(
page 182)
C Comfort For comfort driving
S Sport For standard drivingThe selected program mode appears in the
right multifunction display.
1Current program mode
Press program mode selector switch
repeatedly until the letter of the
desired program mode appears in the
right multifunction display.
SelectCfor comfort driving:

The vehicle starts out in second
gear (both forward and reverse) for
gentler starts. This does not apply if
full throttle is applied or gear
range1 is selected.

Traction and driving stability are
improved on icy roads.

Upshifts occur earlier even when
you give more gas. The engine then
operates at lower rpms and the
wheels are less likely to spin.
SelectSfor standard driving:

The vehicle starts out in first gear.

Upshifts occur later.
!Never change the program mode when the
gear selector lever is out of park positionP. This
could result in a change of driving characteristics
for which you may not be prepared.
iThe last selected program mode (CorS) is
switched on when the engine is restarted.

180 Controls in detail
Automatic transmission
Canceling gear range limit
Press and hold the gear selector lever
in theD+direction until
D reappears in
the right multifunction display
(
page 174).
The transmission will shift from the
current gear range directly to gear
rangeD.
Shifting into optimal gear range
Press and hold the gear selector lever
in theD-direction.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.Steering wheel gearshift control
one-touch gearshifting*
Steering wheel gearshift control is avail-
able on vehicles with Sport Package*, on
SL 55 AMG, and on SL 65 AMG only.
With the gear selector lever in drive
positionD and driving in program modeC
orS, you can limit or extend the gear
range.
If your vehicle is equipped with the
MANUAL shift program, you can use the
steering wheel gearshift control to
manually shift the gears.
iFor information on using the steering
wheel gearshift control in program mode
MANUAL, see “Manual shift program
(SL55AMGandSL65AMG only)”
(
page 182).
!Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

182 Controls in detail
Automatic transmission
Canceling gear range limit
Pull and hold right shift paddle2
until
D reappears in the right multifunc-
tion display (
page 174).
The transmission will shift from the
current gear range directly to gear
rangeD.
Shifting into optimal gear range
Pull and hold left shift paddle1.
The transmission will automatically
select the gear range suited for optimal
acceleration and deceleration. This will
involve shifting down one or more
gears.Manual shift program
(SL55AMGandSL65AMG only)
In addition to the automatic shift
programC orS, your vehicle is equipped
with the MANUAL shift program.
In the MANUAL program mode,
system-controlled automatic gearshifting
is switched off and you need to change the
gears by manually upshifting or downshift-
ing using the steering wheel gearshift
paddles (
page 181) or the gear selector
lever.The program mode selector switch is
located on the lower part of the center
console.
Program mode selector switch
MANUAL For manual gear shifting
C Comfort For comfort driving
S Sport For standard driving
The selected program mode appears in the
right multifunction display (
page 178).
!Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.
iFor information on automatic program
modesC orS, see “Automatic shift program”
(
page 177), “Gear selector lever one-touch
gearshifting” (
page 179), and “Steering wheel
gearshift control one-touch gearshifting*”
(
page 180).

378 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
TReduced
Brake Effect
Depress brake
pedal fully.The electro-hydraulic brake system
is in emergency operation mode.
Considerably greater brake pedal
force is required and the brake
pedal travel is longer. The stopping
distance is increased.
The maximum speed is limited to
55 mph (90 km/h).Stop the vehicle in a safe location or as soon
as it is safe to do so.
Apply the parking brake (page 63).
Do not drive any further.
Prevent the vehicle from rolling away by
blocking the wheels with wheel chocks or
other sizeable objects.
Contact an authorized Mercedes-Benz Center
or call for Roadside Assistance (
page 253).
Warning!G
Driving while this message is displayed can
result in an accident. Have your brake
system checked immediately.
If the electro-hydraulic brake system enters
its emergency operation mode, the driver
must apply significantly greater brake pedal
pressure and depress the pedal much
further than normal to obtain braking effect.
If necessary, apply full pressure to the brake
pedal. Brakes are only applied to the front
wheels. Stopping distance is increased!
If there is a malfunction in the
electro-hydraulic brake system, we recom-
mend that the vehicle be transported with
all wheels off the ground using flatbed or ap-
propriate wheel lift/dolly equipment.A tow bar must be used if circumstances do
not permit the use of the recommended
towing methods and the vehicle requires
towing with all four wheels on the ground.
Towing the vehicle with all four wheels on
the ground is only permissible for distances
up to 30 miles (50 km) and at a speed not to
exceed 30 mph (50 km/h). For more infor-
mation, see “Towing the vehicle”
(
page 434).

379 Practical hints
What to do if …
Left displayRight displayPossible cause/consequencePossible solution
USA only:
;
Canada only:
3
Reduced
Brake Effect
Service
RequiredThe electro-hydraulic brake system
is in emergency operation mode.
Considerably greater brake pedal
force is required and the brake
pedal travel is longer. The stopping
distance is increased.Stop the vehicle in a safe location or as soon
as it is safe to do so.
Apply the parking brake (page 63).
Do not drive any further.
Prevent the vehicle from rolling away by
blocking the wheels with wheel chocks or
other sizeable objects.
Contact an authorized Mercedes-Benz Center
or call for Roadside Assistance (
page 253).
Warning!G
Driving while this message is displayed can
result in an accident. Have your brake
system checked immediately.
If the electro-hydraulic brake system enters
its emergency operation mode, the driver
must apply significantly greater brake pedal
pressure and depress the pedal much
further than normal to obtain braking effect.
If necessary, apply full pressure to the brake
pedal. Brakes are only applied to the front
wheels. Stopping distance is increased!
If there is a malfunction in the
electro-hydraulic brake system, we recom-
mend that the vehicle be transported with
all wheels off the ground using flatbed or ap-
propriate wheel lift/dolly equipment.A tow bar must be used if circumstances do
not permit the use of the recommended
towing methods and the vehicle requires
towing with all four wheels on the ground.
Towing the vehicle with all four wheels on
the ground is only permissible for distances
up to 30 miles (50 km) and at a speed not to
exceed 30 mph (50 km/h). For more infor-
mation, see “Towing the vehicle”
(
page 434).

434 Practical hints
Towing the vehicle
Mercedes-Benz recommends that the vehi-
cle be transported with all wheels off the
ground using flatbed or appropriate wheel
lift/dolly equipment.
When circumstances do not permit the
recommended towing methods, the
vehicle may be towed with all wheels on
the ground or front wheels raised only so
far as necessary to have the vehicle moved
to a safe location where the recommended
towing methods can be employed.
!Do not tow-start the vehicle.
!Use flatbed or wheel lift/dolly equipment
with SmartKey in starter switch turned to
position0.
Do not tow with sling-type equipment. Towing
with sling-type equipment over bumpy roads will
damage radiator and supports.
To prevent damage during transport, do not tie
down vehicle by its chassis or suspension parts.
Switch off the tow-away alarm (
page 100) and
the automatic central locking (
page 166).
Warning!G
If circumstances require towing the vehicle
with all wheels on the ground, always tow
with a tow bar if:

the engine will not run

there is a malfunction in the
electro-hydraulic brake system

there is a malfunction in the power sup-
ply or in the vehicle’s electrical system
This is necessary to adequately control the
towed vehicle.
Prior to towing the vehicle with all wheels on
the ground, make certain that the SmartKey
is in starter switch position2.
Warning!G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is
increased! Adapt your driving style
accordingly. For more information, see
“Electro-hydraulic brake system”
(
page 94).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the ve-
hicle. Adapt your driving accordingly.

449 Technical data
Rims and tires
Rims and tires
!Only use tires which have been tested and
approved by Mercedes-Benz. Tires approved by
Mercedes-Benz are developed to provide best
possible performance in conjunction with the
driving safety systems on your vehicle such as
ABS or ESP
®. Tires specially developed for your
vehicle and tested and approved by
Mercedes-Benz can be identified by finding the
following on the tire’s sidewall:

MO = Mercedes-Benz Original equipment
tires

MO1 = Mercedes-Benz Original equipment
tires (applicable to selected tire sizes only)

MOE = Mercedes-Benz Original Extended
(tires with limited run-flat characteristics)
original equipment tires
Using tires other than those approved by
Mercedes-Benz may result in damage that is not
covered by the Mercedes-Benz Limited
Warranty.
iFor information on driving with MOExtended
tires, see “MOExtended system” (
page 312).
!Using tires other than those approved by
Mercedes-Benz can have detrimental effects,
such as

poor handling characteristics

increased noise

increased fuel consumption
Moreover, tires and rims not approved by
Mercedes-Benz may, under load, exhibit dimen-
sional variations and different tire deformation
characteristics that could cause them to come
into contact with the vehicle body or axle parts.
Damage to the tires or the vehicle may be the
result.
iFurther information on tires and rims is
available at any authorized Mercedes-Benz
Center. A placard with the recommended tire in-
flation pressures is located on the driver’s door
B-pillar. Some vehicles may have supplemental
tire inflation pressure information for driving at
high speeds (
page 301) or for vehicle loads
less than the maximum loaded vehicle condition
(
page 301). If such information is provided, it
can be found on the placard located on the
inside of the fuel filler flap.The tire inflation pressure should be checked
regularly and should only be adjusted on cold
tires. Follow tire manufacturer’s maintenance
recommendation included with vehicle.
iThe following pages also list the approved
wheel rim and tire sizes for equipping your vehi-
cles with winter tires. Winter tires are not avail-
able as standard or optional factory equipment,
but can be purchased from an authorized
Mercedes-Benz Center.
Depending on vehicle model and the standard or
optional factory-equipped wheel rim/tire config-
uration on your vehicle (Performance Package,
Sport Package etc.), equipping your vehicle with
winter tires approved for your vehicle model may
also require the purchase of two or four wheel
rims of the recommended size for use with these
winter tires. See an authorized Mercedes-Benz
Center for more information.

452 Technical data
Rims and tires
ModelSL 55 AMG*
SL 550 (Sport Package*)
SL 600 (Sport Package*)SL 55 AMG
SL 55 AMG (Performance Package*)
SL 65 AMG
Front axle:
Rims (light alloy)8.5 J x 18 H28.5 J x 19 H2
Wheel offset1.18 in (30 mm)1.18 in (30 mm)
Summer tires1
1Radial-ply tires
255/40 ZR18 95Y255/35 ZR19 96Y XL (Extra Load) MO1
Rear axle:
Rims (light alloy)9.5 J x 18 H29.5 J x 19 H2
Wheel offset1.30 in (33 mm)1.22 in (31 mm)
Summer tires1,2
2Must not be used with snow chains.
285/35 ZR18 97Y285/30 ZR19 98Y XL (Extra Load) MO1