brake light MERCEDES-BENZ SL55AMG 2003 R230 Owner's Manual

Contents
Retractable hardtop........................... 159
Opening and closing the retractable
hardtop ........................................ 159
Driving systems ................................. 168
Cruise control .............................. 168
Distronic* .................................... 171
Active Body Control (ABC) ........... 183
Parktronic system* ...................... 186
Useful features .................................. 190
Interior storage spaces ................ 190
Ashtray......................................... 196
Cigarette lighter ........................... 197
Heated steering wheel* (Canada
only–model SL 500) ..................... 197
Easy-Pack load assist in the trunk 198
Electrical outlet ............................ 199
Telephone* .................................. 199
Tele Aid ........................................ 200
Garage door opener ..................... 208Operation......................................... 213
The first 1000 miles (1500 km) ......... 214
Driving instructions............................ 215
Drive sensibly – save fuel............. 215
Drinking and driving ..................... 215Pedals ........................................... 215
Power assistance .......................... 216
Brakes........................................... 216
Driving off ..................................... 218
Parking.......................................... 218
Tires .............................................. 219
Hydroplaning................................. 219
Tire traction .................................. 220
Tire speed rating ........................... 220
Winter driving instructions ............ 221
Standing water.............................. 222
Passenger compartment ............... 222
Driving abroad .............................. 222
Control and operation of radio trans-
mitters .......................................... 222
Catalytic converter........................ 223
Emission control ........................... 224
Coolant temperature..................... 224
At the gas station ............................... 225
Check regularly and before a
long trip ........................................ 226Engine compartment .......................... 227
Hood ............................................. 227
Engine oil ...................................... 228
Transmission fluid level ................ 230
Oil level in the ABC system ........... 230
Coolant ......................................... 230
Battery .......................................... 232
Windshield washer system and
headlamp cleaning system ........... 233
Tires and wheels ................................ 234
Important guidelines ..................... 234
Life of tires ................................... 235
Direction of rotation ..................... 235
Checking tire inflation pressure .... 235
Rotating wheels ............................ 238
Winter driving ..................................... 239
Winter tires ................................... 239
Block heater (Canada only) ........... 240
Snow chains ................................. 240
Maintenance ...................................... 241
Clearing the service indicator ....... 241
Service term exceeded ................. 241
Calling up the service indicator .... 242
Resetting the service indicator ..... 242
Vehicle care ....................................... 243
Cleaning and care of the vehicle ... 243

28 Getting startedUnlockingThe “Getting started” section provides an
overview of the vehicle’s most basic func-
tions. First-time Mercedes-Benz owners
should pay special attention to the infor-
mation given here.
If you are already familiar with the basic
functions described here, the “Controls in
detail” section will help you with further in-
formation. The corresponding page refer-
ences are at the end of each segment.
UnlockingUnlocking with the SmartKeyElectronic key with remote control1‹
Lock button
2
Š
Unlock button for trunk lid
3
Œ
Unlock button
4
Â
Panic button

Press unlock button3
Œ
on the key.
The indicator lamps light up for a short
time. The locking knobs in the doors
move up.

Get in the vehicle and insert the key in
the starter switch.iThe SBC brake system is activated.iOpening a door causes the windows on
that side of the car to open slightly.
They will return to the up position when
the door is closed.

68 Safety and SecurityDriving safety systems
Driving safety systemsIn this section you will find information on
the following driving safety systems:

ABS (A
ntilock B
rake S
ystem)


BAS (B
rake A
ssist S
ystem)


ESP (E
lectronic S
tability P
rogram)


SBC brake system (S
ensotronic B
rake
C
ontrol)
ABS
The ABS regulates the brake pressure so
that the wheels do not lock during braking.
This allows you to maintain the ability to
steer your vehicle.
The ABS is functional above a speed of ap-
proximately 5 mph (8 km/h) independent
of road surface conditions.
On slippery road surfaces, the ABS will re-
spond even with light brake pressure.
If the ABS activates during braking, the
ABS/ESP warning lamp
v
in the speed-
ometer dial flashes. Because of the SBC
brake system, you will not feel any pulsa-
tion in the brake pedal.
iIn winter operation, the maximum ef-
fectiveness of the ABS, the BAS, the
ESP, and SBC is only achieved with win-
ter tires (M + S tires), or snow chains as
required.
Warning!
G
The following factors increase the risk of ac-
cidents:

excessive speed, especially in turns


wet and slippery road surfaces


following another vehicle too closely
ABS, BAS, ESP and SBC cannot reduce this
risk.
Always adjust your driving style to the pre-
vailing road and weather conditions.
Warning!
G
Do not pump the brake pedal, rather use
firm, steady brake pedal pressure. Pumping
the brake pedal defeats the purpose for ABS
and significantly reduces braking effective-
ness.

69 Safety and Security
Driving safety systems
The
-
warning lamp in the speedome-
ter (
page 21) lights up when you turn the
key to position1 or2. It goes out when the
engine is running.
Flashing warning lamp while braking
The v
warning lamp flashes whenever
the ABS is activated. Always adapt your
driving style to the prevailing road and
weather conditions.

When the ABS is in the regulating
mode, continue to apply pressure on
the brake pedal.
BAS
The Brake Assist System (BAS) operates in
emergency situations. If you apply the
brakes very quickly, the BAS automatically
provides full brake boost thereby potential-
ly reducing the braking distance. Apply
continuous full braking pressure until the
emergency braking situation is over. The
ABS will prevent the wheels from locking.
When you release the brake pedal the
brakes function again as normal. The BAS
is then deactivated.
Warning!
G
The ABS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking or steering efficiency be-
yond that afforded by the condition of the
vehicle brakes and tires or the traction af-
forded. The ABS cannot prevent accidents,
including those resulting from excessive
speed in turns, following another vehicle too
closely, or aquaplaning. Only a safe, atten-
tive, and skillful driver can prevent acci-
dents. The capabilities of an ABS equipped
vehicle must never be exploited in a reck-
less or dangerous manner which could jeop-
ardize the user’s safety or the safety of
others.

70 Safety and SecurityDriving safety systems
ESP
The Electronic Stability Program (ESP)
monitors the vehicle's traction (force of
adhesive friction between the tires and the
road surface) and handling.
The ESP recognizes when a wheel is spin-
ning or if the vehicle starts to skid. By ap-
plying brakes to the appropriate wheel and
by limiting engine output, the ESP works to
stabilize the vehicle. The ESP is especially
useful while driving off and on wet or slip-
pery road surfaces.
The ABS/ESP warning lamp
v
in the
speedometer dial flashes when the ESP is
engaged.
The warning lamp
v
in the speedome-
ter dial (
page 21) lights up when you
turn the key to position1 or2. It goes out
when you start the engine
Warning!
G
BAS cannot prevent the natural laws of
physics from acting on the vehicle, nor can
it increase braking efficiency beyond that af-
forded by the condition of the vehicle brakes
and tires or the traction. The BAS cannot
prevent accidents, including those resulting
from excessive speed in turns, following an-
other vehicle too closely, or hydroplaning.
Only a safe, attentive, and skillful driver can
prevent accidents. The capabilities of a BAS
equipped vehicle must never be exploited in
a reckless or dangerous manner which
could jeopardize the user’s safety or the
safety of others.
Warning!
G
Never switch off the ESP when you see the
ABS/ESP-warning lamp
v
flashing in
the speedometer dial. In this case proceed
as follows:


While driving off, apply as little throttle
as possible.


While driving, ease up on the accelera-
tor.


Adapt your speed and driving style to
the prevailing road conditions.
Failure to observe these guidelines could
cause the vehicle to skid.
The ESP cannot prevent accidents resulting
from excessive speed.

72 Safety and SecurityDriving safety systemsThe button is located in the lower part of
the center console.
1ESP on/off
Press ESP button1 until the ESP warn-
ing lamp
v
in the speedometer
lights up.
ESP is deactivated.
If one or more wheels are spinning, the
ESP warning lamp v
in the speedome-
ter flashes, regardless of the speed.
Traction control brakes a spinning wheel
even when ESP is deactivated.
ESP always operates when you are brak-
ing, even when it has been deactivated.Switching on ESP

Press button1.
The ESP warning lamp
v
in the
speedometer goes out. You are now
again in normal driving mode.
SBC brake system
The SBC brake system combines a hydrau-
lic brake circuit with electronically con-
trolled brake servo assistance. You have
increased braking safety and improved
braking comfort.
!Avoid spinning of a drive wheel for an
extended period with the ESP switched
off. This may cause serious damage to
the drive train which is not covered by
the Mercedes-Benz Limited Warranty.Warning!
G
When the ESP warning lamp
v
is
illuminated continuously, ESP is switched
off.
Adapt your speed and driving to the prevail-
ing road conditions and to the non-operating
status of the ESP.
Warning!
G
Never ignore a brake malfunction indicated
in the speedometer display, for example by
the
;
(USA only) or
3
(Canada only)
indicator lamp. Refer to the “Practical hints”
section (
page 253). Also read and ob-
serve the messages in the instrument clus-
ter display (page 257).

73 Safety and Security
Driving safety systems
The SBC brake system is automatically ac-
tivated when you:

unlock the vehicle with the key or the
KEYLESS-GO* card


open the driver’s or passenger door


turn the key in the starter switch to
position1


in vehicles with KEYLESS-GO*, press
start/stop button on selector lever
once


depress the brake pedal


release the parking brake
Warning!
G
The SBC brake system requires electrical
power to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. In such a case, the
red brake warning lamp (
page 253) and
the warning messages (
page 265) light up
while driving. To brake, the driver must then
apply significantly greater brake pedal pres-
sure and depress the pedal much further to
obtain the expected braking effect. If neces-
sary, apply full pressure to the brake pedal.
Brakes are only applied to the front wheels.
Stopping distance is increased!
If there is a malfunction in the SBC brake
system, we recommend that the vehicle be
transported with all wheels off the ground
using flatbed or appropriate wheel lift/dolly
equipment.
A tow bar must be used if circumstances
do not permit the use of the recommended
towing methods and the vehicle requires
towing with all four wheels on the ground.
Towing the vehicle with all four wheels on
the ground is only permissible for distances
up to 30 miles (50 km) and at a speed not
to exceed 30 mph (50 km/h). For more in-
formation, refer to “Towing the vehicle”
(page 325).
iIf the SBC brake system is activated as
the brake pedal is first depressed, you
may feel a reduced pedal resistance
and longer pedal travel than normal.
When releasing the pedal, you may also
feel the brake pedal pulsate and you
may hear a sound which is caused by
the activation of the SBC pump. This is
normal and not an indication of a mal-
function. Pedal travel returns to normal
when you release the brake pedal and
the sound soon ceases.

173 Controls in detail
Driving systems
Distronic displays in the speedometer
dial
If Distronic detects a vehicle directly
ahead, the DTR indicator lamp
E
in the
speedometer dial lights up white.
If the distance to the vehicle ahead is too
small for the DTR to be able to maintain the
preset distance, the DTR warning lamp
E
in the speedometer lights up red.
If Distronic calculates that there is a dan-
ger of collision


the DTR warning lamp
E
in the
speedometer lights up red


an intermittent warning sounds

Immediately brake the vehicle to avoid
a collision.
Under no circumstances should the
driver await the intermittent warning
sound before braking. See warning
note to the right. The intermittent warning sound ceases
and the red DTR warning lamp
E

goes out when the necessary distance
to the vehicle ahead is again estab-
lished.
1Red DTR warning lamp
E
Warning!
G
An intermittent warning sounds and the
DTR warning lamp (red) in the speedometer
dial is illuminated if the Distronic system cal-
culates that the distance to the vehicle
ahead and your vehicle’s current speed indi-
cate that Distronic will not be capable of
slowing the vehicle sufficiently to maintain
the preset following distance, which creates
a danger of a collision.
Immediately brake the vehicle to increase
the distance to the vehicle in front of you.
The warning sound is intended as a final cau-
tion that you have not interceded with your
own braking inputs to avoid a potentially
dangerous situation. Do not wait for the op-
eration of the warning signal to intercede
with your own braking, as that will result in
potentially dangerous emergency braking
which will not always result in an impact be-
ing avoided.
Tailgating increases the risk of an accident.

179 Controls in detail
Driving systems
1Distance warning function on/off
switch
2Thumbwheel for setting distance
Increasing distance
Increasing the distance setting tells Dis-
tronic to maintain a greater following dis-
tance to the vehicle ahead.
Turn thumbwheel2 towards
¯
.Decreasing distance
Decreasing the distance setting tells Dis-
tronic to maintain a smaller following dis-
tance to the vehicle ahead.

Turn thumbwheel2 towards
®
.Distance warning function
When Distronic is deactivated, this func-
tion will continue to warn you if you are fol-
lowing too close to the vehicle ahead:


The DTR warning lamp
E
lights up
red.


An intermittent warning will sound if
necessary.
If these warnings are issued, you must
brake manually to maintain a safe distance
and avoid a collision with the vehicle
ahead.

180 Controls in detailDriving systems
Activating
Press switch1.
The indicator lamp on the switch lights
up. A loudspeaker symbol appears in
the speedometer display (
page 174).
Deactivating

Press switch1.
The indicator lamp on the switch goes
out. No loudspeaker symbol appears in
the speedometer display.Driving with Distronic
This section describes a number of driving
situations where special precaution is re-
quired on the part of the driver. Be pre-
pared to brake in such situations. This will
deactivate the Distronic system.
Warning!
G
If the DTR warning lamp (red)
E
in the
speedometer dial lights up while driving
and/or an intermittent warning sounds, im-
mediate attention on the part of the driver is
required.
As required by the traffic situation, apply the
brakes and navigate around a possible ob-
stacle. However, do not drive by relying on
the distance warning function, as this will re-
sult in an emergency braking application.
Especially depending on road surface condi-
tions and driver reaction, this will not always
enable you to avoid a collision.
iComplex driving situations are not al-
ways fully recognized by Distronic. This
could result in wrong or missing dis-
tance warnings.