light MERCEDES-BENZ SLC 2017 Workshop Manual

Limited braking performance on salt-
treated roads If you driv eons alted roads ,al ayer of salt resi-
due may for mont he brak ed isc sa nd brake
pads. This can result in as ignificantly longer
braking distance. R
In orde rtop revent any salt build-up, apply the
brakes occasionally while paying attention to
th et ra ffic conditions.R
Carefully depress th eb rak ep edal and the
beginnin ga nd end of aj ou rney.R
Maintain ag reater distanc etot he vehicle
ahead.
Servicing th eb rakes
! The brak ef luid level may be to ol ow, if:R
if th er ed brak ew arning lamp light supi n
th ei nstrumen tc luster andR
you hear aw arning tone while th ee ngine is
running
Observe additional warning messages in the
multifunction display.
The brak ef luid level may be to ol ow due to
brak ep ad wear or leaking brak el ines.
Hav et he brak es ystem checked immediately.
Consult aq ualifie ds pecialist workshop to
arrange this.
! As th eE SP ®
system operates automatically,
th ee ngine and th ei gnitio nm ust be switched
off (SmartKey in position 0 or 1 in th ei gnition
lock) if th ee lectric parking brak eisb ein gt es-
ted on ab rak ed ynamometer (maximum
10 seconds).
Brakin gt ri ggered automatically by ESP ®
may
seriously damage th eb rak es ystem.
All check sa nd maintenanc ew ork on th eb rake
system must be carried out at aq ualifie ds pe-
cialis tw orkshop.
Hav eb rak ep ads installe da nd brak ef luid
replaced at aq ualifie ds pecialist workshop.
If th eb rak es ystem has onl yb een subject to
moderat el oads, you should tes tt he functional-
ity of your brakes at regular intervals.
Information on BA S( Brake Assist )( Y
page 55).
Mercedes-Ben zr ecommend st ha ty ou onl yh ave
brak ep ads/linings installe dony our vehicle
whic hh ave been approved for Mercedes-Benz
vehicle sorw hic hc orrespon dtoane quivalent
qualit ys ta ndard. Brake pads/linings whic hh ave not been approved for Mercedes-Ben zv ehicle s
or whic ha re n ot of an equivalent qualit yc ould
affect your vehicle's operatin gs afety.
Mercedes-Ben zr ecommend st ha ty ou onl yu se
brak ef luid that has been specially approved for
your vehicle by Mercedes-Benz, or whic hc orre-
sponds to an equivalent qualit ys ta ndard. Brake
fluid whic hh as not been approved for
Mercedes-Ben zv ehicle sorw hic hisn ot of an
equivalent qualit yc ould affect your vehicle's
operatin gs afety.
High-performance brake system
(Mercedes-Benz SLC 43 AMG) AM Gb rak es ystems are designed for heavy
loads and have component sw ith corresponding
properties. This may lead to noise when braking.
This will depen do n: R
Speed R
Brakin gf orce R
Ambien tc onditions, e.g .t emperature and
humidity
The wear of individual component soft he brake
system, such as th eb rak ep ads/linings or brake
discs, depends on th ei ndividual driving style
and operatin gc onditions.
For this reason, it is impossibl etos ta te am ile-
age that will be valid unde ra ll circumstances. An
aggressiv ed riving style will lead to high wear.
You can obtain mor ei nformatio nont hi sf ro ma
qualifie ds pecialist workshop.
New and replaced brak ep ads and disc so nly
reac ht he ir optimum braking effect after several
hundred kilometers of driving .C ompensate for
this by applyin gg reater force to th eb rak ep edal.
Keep this in mind, and adapt your driving and
braking accordingl yd urin gt hi sb reak-in period.
Excessive heavy braking results in correspond-
ingly high brak ew ear. Observe th eb rak es ystem
warning lamp in th ei nstrumen tc luster and note
any brak es ta tus messages in th em ultifunction
display. Especially for high performanc ed riving,
it is important to maintain and have th eb rake
system checked regularly. Driving tips 137
Driving and parking Z

importan tift he vehicle is laden. By doing so, you
will make use of the braking effect of the engine.
This relieves the load on the brak es ystem and
prevent st he brakes fro mo verheatin ga nd wear-
ing too quickly.
If Distanc eP ilot DISTRONIC detect st hat there is
ar isk of ac ollision, you will be warne dv isually
and acoustically. Without your intervention, Dis-
tance Pilot DISTRONIC cannot prevent ac olli-
sion .Ani ntermitten tw arnin gt on ew ill then
sound and the distanc ew arnin gl amp will light
up in the instrumen tc luster. Brak ei mmediately
in order to increase the distanc ef ro mt he vehi-
cle in front ,ort ak ee vasiv ea ction, provided it is
safe to do so.
For Distanc eP ilot DISTRONIC to assist you
when driving, the radar sensor system must be
operational.
Distanc eP ilot DISTRONIC operates in the range
betwee n0m ph (0 km/h) and 120 mph
(200 km/h).
Do not use Distanc eP ilot DISTRONIC on roads
with steep gradients.
As Distanc eP ilot DISTRONIC transmits radar
waves, it can resemble the radar detectors of
the responsible authorities .Y ou can refe rtot he
relevant chapter in the Operator's Manual if
questions are asked about this.
i USA only: This devic eh as been approved by
the FCC as a" Vehicular Radar System". The
radar sensor is intended for use in an auto-
motive radar system only. Removal, tamper-
ing, or altering of the devic ew ill void any war-
ranties, and is not permitted by the FCC. Do
not tamper with, alter ,oru se in any non-
approved way.
An yu nauthorized modification to this device
could void the user's authority to operat et he
equipment.
i Canada only: This devic ec omplies with
RS S-210 of Industr yC anada. Operation is
subject to the followin gt wo conditions:
1. This devic em ay not cause harmful inter-
ference, and
2. This devic em ust accept any interference
received, including interference that may
cause undesired operation of the device.
Removal, tampering, or altering of the device
will void any warranties ,a nd is not permitted.
Do not tamper with, alter ,oru se in any non-
approved way. An yu nauthorized modification to this device
could void the user's authority to operat et he
equipment.
Important safety notes
G WARNING
Distanc eP ilot DISTRONIC does not react to: R
people or animals R
stationar yo bject sont he road, e.g. stopped
or parked vehicles R
oncomin gv ehicles and crossin gt ra ffic
As ar esult ,D istanc eP ilot DISTRONIC may
neither give warnings nor intervene in such
situations .T here is ar isk of an accident.
Always pay careful attention to the traffic sit-
uation and be ready to brake.
G WARNING
Distanc eP ilot DISTRONIC cannot always
clearly identify other road users and complex
traffic situations.
In such cases ,D istanc eP ilot DISTRONIC may:R
give an unnecessary warnin ga nd then
brak et he vehicle R
neither give aw arnin gn or interveneR
accelerat eorb rak eu nexpectedly
There is ar isk of an accident.
Continue to drive carefully and be ready to
brake, especially if Distanc eP ilot DISTRONIC
warns you.
G WARNING
Distanc eP ilot DISTRONIC brakes your vehicle
with up to 50% of the maximum possible
deceleration. If this deceleratio nisn ot suffi-
cient, Distanc eP ilot DISTRONIC alert sy ou
with av isual and acoustic warning. There is a
risk of an accident.
Apply the brakes yourself in these situations
and tr yt ot ak ee vasiv ea ction.
! When Distanc eP ilot DISTRONIC or the
HOL Df unction is activated, the vehicle
brakes automatically in certain situations.Driving systems 141
Driving and parking Z

! When parking, pay particular attention to
objects above or below the sensors, such as
flower pots or trailer drawbars. PARKTRONIC
does not detect such objects when they are in
the immediate vicinity of the vehicle. You
could damage the vehicle or the objects.
The sensors may not detect snow and other
objects that absorb ultrasonic waves.
Ultrasonic sources such as an automatic car
wash, the compressed-air brakes on at ruck
or ap neumatic drill could cause PARKTRONIC
to malfunction.
PARKTRONIC may not function correctly on
uneven terrain.
PARKTRONIC is activated automaticall yw hen
you: R
switch on the ignition R
shift the transmission to position D , R or NR
release the electric parking brake
PARKTRONIC is deactivated at speeds above
11 mph (18 km/h). It is reactivated at lower
speeds.
Range of the sensors
General notes PARKTRONIC does not take objects into con-
sideration that are: R
below the detection range, e.g. people, ani-
mals or objects. R
above the detection range, e.g. overhanging
loads, truck overhangs or loading ramps.
C
Sensors in the front bumper, left-hand side
(example)
The sensors must be free from dirt, ice or slush.
They can otherwise not function correctly. Clean
the sensors regularly, taking care not to scratch
or damage them ( Y
page 240). Range
Front sensors
Center Approx. 40 in (approx.
100 cm)
Corners Approx. 24 in (approx.
60 cm)
Rear sensors
Center Approx. 48 in (approx.
120 cm)
Corners Approx. 32 in (approx.
80 cm)
Minimum distance
Center Approx. 8i n( approx. 20 cm)
Corners Approx. 6i n( approx. 15 cm)
If there is an obstacle within this range, the rel-
evant warning displays light up and aw arning
tone sounds. If the distance falls below the min-
imum, the distance may no longer be shown.150
Driving systems
Driving and parking

Problems with PARKTRONIC Problem
Possible causes/consequences and P Solutions
Only the red segments in
the PARKTRONIC warn-
ing display sa re lit. You
also hear aw arning tone
for approximately two
seconds.
PARKTRONIC is deacti-
vated after approx-
imately 20 seconds, and
the indicator lamp in the
PARKTRONIC button
lights up. PARKTRONIC has malfunctioned and has switched off. X
If problems persist, have PARKTRONIC checked at aq ualified spe-
cialist workshop.
Only the red segments in
the PARKTRONIC warn-
ing display sa re lit.
PARKTRONIC is deacti-
vated after approx-
imately five seconds. The PARKTRONIC sensors are dirty or there is interference. X
Clean the PARKTRONIC sensors ( Y
page 240).X
Switch the ignition back on.
The problem may be caused by an external source of radio or ultra-
sound waves. X
See if PARKTRONIC functions in ad ifferent location.
Parking Guidance
Important safety notes Parking Guidance is an electronic parking aid
with ultrasound. Ultrasound is used to measure
the road on both sides of the vehicle. As uitable
parking space is indicated by the parking sym-
bol. You receive steering instructions when
parking. You may also use PARKTRONIC
( Y
page 149).
Parking Guidance is only an aid. It is not a
replacement for your attention to your immedi-
ate surroundings. You are always responsible
for safe maneuvering, parking and exiting a
parking space. When maneuvering, parking or
pulling out of ap arking space, make sure that
there are no persons, animals or object sint he
area in which you are maneuvering.
G WARNING
If object sa re located above the detection
range, Parking Guidance may provide steering
instructions too soon. You may cause ac olli-
sion as ar esult. There is ar isk of an accident.
If object sa re located above the detection
range, stop and switch off Parking Assist. ! If unavoidable, you should drive over obsta-
cles such as curbs slowly and not at as harp
angle. Otherwise, you may damage the
wheels or tires.
When PARKTRONIC is deactivated, Parking
Guidance is also unavailable.
Parking Guidance may also display spaces not
suitable for parking, e.g.: R
where parking or stopping is prohibited R
in front of driveways or entrances and exits R
on unsuitable surfaces
Use Parking Guidance for parking spaces: R
that are paralle ltot he direction of travelR
that are on straight roads, not bends R
that are on the same level as the road, i.e. not
on the pavement, for example. Parking Guid-
ance may not detect flat curbs
Parking tips: R
On narrow roads, drive as close to the parking
space as possible. R
Parking spaces that are littered or overgrown
might be identified or measured incorrectly. R
Parking spaces that are partially occupied by
trailer drawbars might not be identified as
such or be measured incorrectly.152
Driving systems
Driving and parking

Under the following circumstances, the rear
view camera will not function, or will function in
al imited manner: R
if the trunk lid is open R
in heavy rain, snow or fog R
at night or in very dark places R
if the camera is exposed to very bright light R
if the area is lit by fluorescent bulb sorL ED
lighting (the displa ym ay flicker)R
if there is as udden change in temperature,
e.g. when driving into ah eated garage in win-
ter R
if the camera lens is dirty or obstructed
Observe the notes on cleaning
( Y
page 240) R
if the rear of your vehicle is damaged. In this
event, have the camera position and setting
checked at aq ualified specialist workshop
The field of vision and other functions of the rear
view camera may be restricted due to additional
accessories on the rear of the vehicle (e.g.
license plate holder, bicycle rack).
For technical reasons, leaving the standard
height can result in inaccuracies in the guide
lines on vehicles with ah eight-adjustable chas-
sis.
i The rear view camera is protected from rain-
drops and dust by means of af lap. When the
rear view camera is activated, this flap opens.
The flap closes agai nw hen:R
you have finished the maneuvering process R
you switch off the engine R
you open the trunk
Observe the notes on cleaning ( Y
page 240).
For technical reasons, the flap may remain
open briefly after the rear view camera has
been deactivated.
Activating/deactivating the rear view
camera X
To activate: make sure that the SmartKey is
in position 2 in the ignition lock.X
Make sure that the Activation by Rg ear
function is selected in the multimedia system;
see the Digital Operator's Manual. X
Engage reverse gear.
The rear view camera flap opens. The multi-
media system shows the area behind the vehi-
cle with guide lines. The image from the rear view camera is avail-
able throughout the maneuvering process.
To deactivate: the rear view camera deacti-
vates if you shift the transmission to P or after
driving forwards as hort distance.
Displays in the multimedia system The rear view camera may show ad istorted view
of obstacles, show them incorrectly or not at all.
The rear view camera does not show objects in
the following positions: R
very close to the rear bumper R
under the rear bumper R
in close range above the handle on the trunk
lid
! Objects not at ground level may appea rt o
be further awa yt han they actually are, e.g.: R
the bumper of ap arked vehicle R
the drawba rofat railer R
the ball coupling of at railer tow hitchR
the rear section of an HGV R
as lanted post
Use the guidelines only for orientation.
Approach objects no further than the bottom-
most guideline.
C
Yello wg uide line at ad istance of approx-
imately 13 ft (4.0 m) from the rear of the
vehicle
D
White guide line without turning the steering
wheel, vehicle width including the exterior
mirrors (static)

Blind Spot Assist monitors the are aupto10f t
(3.0 m) behind your vehicle and directly nex tt o
your vehicle, as shown in the diagram. For this
purpose, Blind Spot Assist uses radar sensor si n
the rear bumper.
If the lanes are narrow, vehicles driving in the
lane beyond the lane nex ttoy our vehicle may be
indicated, especially if the vehicles are not driv-
ing in the middle of their lane. This may be the
case if ther ea re vehicles driving at the inner
edge of their lanes.
Due to the natur eoft he system:R
warning sm ay be issued in error when driving
close to crash barriers or similar solid lane
borders. R
the warning is canceled when driving for an
extended period nex ttol ong vehicles, such as
trucks.
Indicator and warning display
C
Yellow indicator lamp/red warning lamp
Blind Spot Assist is not activ eats peeds below
approximately 20 mph (30 km/h). Vehicles in
the monitoring range are then not indicated.
When Blind Spot Assist is activated, indicator
lamp C in the exterior mirror sl ights up yellow
at speeds of up to 20 mph (3 0k m/ h) .Ats peeds
above 20 mph (30 km/h), the indicator lamp
goe so ut and Blind Spot Assist is operational.
If av ehicl eisd etected within the blind spot
monitoring rang eats peeds above 20 mph
(30 km/h), warning lamp C on the correspond-
ing sid el ig hts up red .T hi sw ar ning is always
emitted when av ehicl ee nter st he blind spot
monitoring rang ef rom behind or from the side.
Whe ny ou overtake av ehicle, the warning only
occurs if the difference in speed is less than
7m ph (12 km/h).
The yellow indicator lamp goe so ut if reverse
gea rise ngaged .Int his event, Blind Spot Assist
is no longer active. The brightness of the indicator/warning lamps
is adjuste da ut omaticall ya ccording to the ambi-
ent light.
Collisio nw arningIf av ehicl eisd etected in the monitoring rang eo f
Blind Spot Assist and yo us witch on the corre-
sponding turn signal ,ad oubl ew ar ning tone
sounds. Re dw ar ning lamp C flashes. If the turn
signal remains on, vehicles detected are indica-
ted by the flashing of red warning lamp C .
There are no further warning tones.
Switchin gonB lind Spo tA ssis tX
Make sure that Blind Spot Assist
( Y
page 171 )i sa ctivate dint he on-board
computer. X
Turn the SmartKey to position 2 in the ignition
lock.
Warning lamps C in the exterio rm irrors light
up red for approximately 1.5 seconds and
then turn yellow.
Lan eK ee ping Assist
General notes
Lane Keeping Assist monitors the are ainf ront of
your vehicl ew it hc amera C ,w hi ch is mounted
at the top of the windshield .L ane Keeping Assist
detects lane markings on the roa da nd warns
yo ub efore yo ul ea ve your lane unintentionally.
If yo us elect km on the on-board compute rint he
Display Unit Speed-/Odometer function
( Y
page 172), Lane Keeping Assist is active
starting at as peed of 60 km/h .Ift he miles
display uni ti ss elected ,t he assistance range
begins at 40 mph.
Aw ar ning may be given if af ront wheel passes
ove ral an em arking. It will warn yo ubym eans of
intermittent vibration in the steering wheel for
up to 1.5 seconds.160
Driving systems
Driving and parking

Important safety notes
G WARNIN G
If you operate information systems and com-
munication equipmen ti ntegrate dint he vehi-
cle while driving ,y ou will be distracte df ro m
traffic conditions. You could also lose control
of th ev ehicle. Ther eisar is kofana ccident.
Only operate th ee quipmen tw hen th et ra ffic
situation permits. If you are no ts ur et ha tt hi s
is possible ,p ark th ev ehicl ep ayin ga ttention
to traffic condition sa nd operate th ee quip-
men tw hen th ev ehicl eiss ta tionary.
You must observ et he legal requirements for th e
country in whic hy ou are currentl yd riving when
operating th eo n-bo ard computer.
G WARNIN G
If th ei nstrumen tc luste rh as faile dorm al-
functioned, you may no tr ecognize function
restriction sins ystems relevan ttos afety. The
operating safet yofy our vehicl em ay be
impaired .T her eisar is kofana ccident.
Drive on carefully. Hav et he vehicl ec hecked
at aq ualified specialist workshop immedi-
ately.
The on-board computer only shows message so r
warning sf ro mc ertai ns ystems in th em ultifunc-
tion display. You should therefor em ak es ur e
your vehicl eiso perating safely at all times .
If th eo perating safet yofy our vehicl ei s
impaired ,p ull ove rass oo nasitiss af etodos o.
Contac taq ualified specialist workshop.
Fo rano verview, see th ei nstrumen tp anel illus-
tration ( Y
page 31).
Display sa nd operation
Instrumen tc luster lighting
The lighting in th ei nstrumen tc luster, in th ed is-
plays and th ec ontrols in th ev ehicl ei nterior can
be adjusted usin gt he brightness control knob.
The brightness control knob is locate dont he
botto ml ef toft he instrumen tc luste r
( Y
page 31). X
Turn th eb rightness control knob clockwise or
counter-clockwise.
If you tur nt he ligh ts witch ( Y
page 93 )t ot he
X , ` or X position ,t he brightness
will depend upon th eb rightness of th ea mbi -
en tl ight.
The ligh ts ensor in th ei nstrumen tc luste r
automatically control st he brightness of th e
multifunction display. In daylight, th ed isplays
in th ei nstrumen tc luste ra re no ti lluminated.
Speedometer with segments The segments in th es peedometer indicat e
whic hs pee dr ange is available. R
Cruis ec ontro la ctivated ( Y
page 138):
The segments ligh tupf ro mt he store ds pee d
to th em aximum speed. R
Distanc eP ilot DISTRONI Cisa ctivated
( Y
page 140):
On eort wo segments in th es et spee dr ange
ligh tu p. R
Distanc eP ilot DISTRONI Cd etects av ehicl ei n
fron tm oving mor es lowly than th es to re d
speed:
The segments between th es pee doft he vehi-
cle in fron ta nd th es to re ds pee dl igh tu p.
Tachometer
! Do no td riv eint he overrevving range, as this
could damag et he engine.
The red ban dint he tachometer indicates th e
engine's overrevving range.
The fuel suppl yisi nterrupted to protect th e
engin ew hen th er ed ban disr eached.
Outsid et emperatur ed isplayYou should pay special attention to road condi-
tion sw hen temperatures are aroun df re ezing
point.
Bea rinm in dt ha tt he outside temperature dis-
play indicates th et em perature measured and
does no tr ecord th er oad temperature.
The outside temperature display is in th em ulti-
function display ( Y
page 165).
Ac ha ng eint he outside temperature is shown in
th em ultifunction display after ad elay.Display sa nd operation 163
On-boar dc omputer and displays Z

Service menu Depending on the equipment installed in the
vehicle, you have the following options in the
Serv. menu:R
Calling up display messages ( Y
page 178)R
Restarting the tire pressure loss warning sys-
tem ( Y
page 262)R
Checking the tire pressure electronically
( Y
page 262)R
Calling up the service due date
( Y
page 235)
Settings menu
Introduction Depending on the equipment installed in the
vehicle, in the Sett. menu you have the follow-
ing options: R
Changing the instrumen tc luster settings
( Y
page 172)R
Changing the light settings ( Y
page 172)R
Changing the vehicle settings ( Y
page 173)R
Changing the convenience settings
( Y
page 174)R
Restoring the factory settings ( Y
page 175)
Instrument cluster
Selecting the distance unit The Display Unit Speed-/Odometer: func-
tion allow sy ou to choose whether certain dis-
play sa ppear in kilometers or miles in the mul-
tifunction display. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Instrument Cluster submenu.X
Press v to confirm.X
Press the d or c button to select the
Display Unit Speed-/Odometer function.
The current setting km or miles appears.X
Press the v button to save the setting.
The selected unit of measurement for distance
applie st o:R
the digital speedometer in the Trip menuR
the odometer and trip odometer R
the trip computer R
the current consumption and the range R
navigation instructions in the Navi menuR
cruise control R
Distanc eP ilot DISTRONIC R
ASSYST PLUS service interval display
Selecting permanent display The Permanent Display: function allow sy ou
to choose whether the multifunction display
always shows the outside temperature or the
speed.
The speed display is inverse to the speedome-
ter. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Instrument Cluster submenu.X
Press v to confirm. X
Press the d or c button to select the
Permanent Display: function.
The current setting, Outside Temperature
or Speedometer [km/h] or Speedometer
[mph] ,a ppears. X
To change the setting: press v again.
Lights
Setting the daytime running lights This function is not available in Canada. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Light submenu. X
Press v to confirm. X
Press the d or c button to select the
Daytime Running Lights function.
If the Daytime Running Lights function has
been switched on, the cone of light and the

X
Press v to confirm.X
Press the d or c button to select the
Amb. Light +/- function.
The curren ts etting appears.X
Press v to confirm.X
Press the d or c button to adjust the
brightness to any level from Off to Level 5
(bright). X
Press the v or 8 button to save the
setting.
Setting the ambient lighting color X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Light submenu.X
Press v to confirm.X
Press the d or c button to select the
Amb. Light Col. function.X
Press v to confirm.X
Press the d or c button to set the color
to SOLAR , SOLAR Orange or SOLAR Red .X
Press the v or 8 button to save the
setting.
Activating/deactivating surround light-
ing and exterior lighting delayed switch-
off X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Light submenu.X
Press v to confirm.X
Press d or c to select the Surround
Lighting function.
If the Surround Lighting function is activa-
ted, the multifunction display shows the light
cone and the area around the vehicle in
orange. X
Press the v button to save the setting.
Deactivating delayed switch-off of the exterior
lighting temporarily: X
Before leaving the vehicle, turn the SmartKey
to position 0 in the ignition lock.X
Turn the SmartKey to position 2 in the ignition
lock.
The exterior lighting delayed switch-off is
deactivated.
Delayed switch-off of the exterior lighting is
reactivated the next time you start the engine. If you have activated the Surround lighting
function and you turn the light switch to X ,
the following functions are activated when it is
dark: R
surround lighting: the exterior lighting
remains lit for 40 seconds after unlocking
with the SmartKey. If you start the engine, the
surround lighting is switched off and auto-
matic headlamp mode is activated
( Y
page 93). R
exterior lighting delayed switch-off: the
exterior lighting remains lit for 60 seconds
after the engine is switched off. If you close all
the doors and the trunk lid, the exterior light-
ing goes off after 15 seconds.
Dependin gony our vehicle's equipment, when
the surround lighting and delayed switch-off
exterior lighting are on, the following light up: R
Parking lamps R
Low-beam headlamps R
Daytime runnin gl amps R
Side marker lamps R
Surround lighting in the exterior mirrors
Activating/deactivating the interior light-
ing delayed switch-off If you activat et he Interior Lighting Delay
function, the interior lighting remains on for
20 seconds after you remove the SmartKey from
the ignition lock. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Light submenu. X
Press v to confirm. X
Press the d or c button to select the
Interior Lighting Delay function.
When the Interior Lighting Delay func-
tion is activated, the vehicle interior is dis-
played in orange in the multifunction display. X
Press the v button to save the setting.
Vehicle
Activating/deactivating the automatic
door locking mechanism
If you activat et he Automatic Door Lock func-
tion, the vehicle is centrally locked above a
speed of approximately 9m ph (15 km/h).Menus and submenus 173
On-board computer and displays Z

X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Vehicle submenu.X
Press v to confirm.X
Press the d or c button to select the
Automatic Door Lock function.
When the Automatic Door Lock function is
activated, the multifunction display shows the
left-hand vehicle door in orange. X
Press the v button to save the setting.
For further information on the automatic locking
feature, see ( Y
page 69).
Activating/deactivating the acoustic
locking verification signal If you switch on the Acoustic Lock function, an
acoustic signal sounds when you lock the vehi-
cle. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Vehicle submenu.X
Press v to confirm.X
Press the d or c button to select the
Acoustic Lock function.
If the Acoustic Lock function is activated,
the 7 symbol in the multifunction display
lights up orange. X
Press the v button to save the setting.
Convenience
Activating/deactivating the EASY-
ENTRY/EXI Tf eature
G WARNING
When the EASY-ENTRY/EXIT feature adjusts
the steerin gw heel, you and other vehicle
occupant s–p articularly children –c ould
become trapped. There is ar isk of injury.
While the EASY-ENTRY/EXIT feature is mak-
ing adjustments, make sure that no one has
any body parts in the sweep of the steering
wheel. If somebody becomes trapped: R
press one of the memory function position
buttons, or R
move the switch for steerin gw heel adjust-
ment in the opposite direction to that in
which the steerin gw heel is moving.
The adjustmen tp rocess is stopped. X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Convenience submenu. X
Press v to confirm. X
Using d or c ,s elect the Easy Entry/
Exit function.
If the Easy Entry/Exit function is activated,
the multifunction display shows the steering
wheel in orange. X
Press the v button to save the setting.
Further information on the EASY-ENTRY/EXIT
feature ( Y
page 87).
Switching the belt adjustment on/off X
Press the Y or e button on the steering
wheel to select the Sett. menu.X
Press the d or c button to select the
Convenience submenu. X
Press v to confirm. X
Press the d or c button to select the
Belt Adjustment function.
When the Belt Adjustment function is acti-
vated, the seat belt is displayed in orange in
the multifunction display. X
Press the v button to save the setting.
For further information on belt adjustment, see
( Y
page 41).
Switching the fold-in mirrors when lock-
ing feature on/off
This function is only availabl ew hen the vehicle is
equipped with the electrical fold-in function.
This function is only availabl einC anada.
When you activat et he Auto. Mirror Folding
function, the exterior mirrors are folded in when
the vehicle is locked.
If you have switched on the Auto. Mirror
Folding function and you fold in the exterior
mirrors using the button on the door
( Y
page 89), they will not fold out automatically.174
Menus and submenus
On-board computer and displays