hood open MERCEDES-BENZ SLK55AMG 2006 R171 User Guide

381 Practical hints
What to do if …
Display symbol
Display message
Possible cause/consequence
Possible solution
A
Fuel reserve
The fuel level has dropped below
the reserve mark.

Refuel at the next gas station (
page 304).
Check gas cap
See Operator’s Manual
The fuel cap may not be closed
properly.

Check the fuel cap (
page 304).
If it is not closed properly:

Close the fuel cap.
If it is closed properly:

Have the fuel system checked by an autho-
rized Mercedes-Benz Center.
K
Lock retractable roof
You are driving with the retractable
hardtop not properly locked.

Stop the vehicle in a safe location. Observe
the traffic situation around you.

Push the retractable hardtop switch forward
or rearward until the retractable hardtop is
completely closed or open (
page 252).
Retractable roof
Visit workshop
The retractable hardtop is
malfunctioning.

Have the retractable hardtop checked by an
authorized Mercedes-Benz Center.
O
Close hood!
You are driving with the hood open.

Close the hood (
page 307).
F
Replace key
The SmartKey is malfunctioning.

Visit an authorized Mercedes-Benz Center.

403 Practical hints
Replacing bulbs
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 110).

Open the hood (
page 307).
1Housing cover for low beam (halogen
headlamps only)
Housing cover for Bi-Xenon* head-
lamps. Do not remove.
2Bulb socket for turn signal lamp
3Bulb socket for high beam/high beam
flasher lamp
4Bulb socket for parking and standing
light lamp
5Bulb socket for low beam bulb
(Halogen headlamps only)
Warning!
G
Do not remove the cover1 for the
Bi-Xenon* headlamp. Because of high volt-
age in Bi-Xenon lamps, it is dangerous to re-
place the bulb or repair the lamp and its
components. We recommend that you have
such work done by a qualified technician.

407 Practical hints
Replacing wiper blades
Installing wiper blades
1Cover
2Guide tab
3Attachment
4Tabs

Maintaining a tilted position of the
wiper blade, place cover1 onto
attachment3 so that guide tab2 is
under cover1.

Tilt the wiper blade in direction of the
arrow towards the wiper arm.

Simultaneously press tabs4 together
and let the wiper blade engage into
both recesses of attachment3.

Check if the wiper blade is securely
fastened.

Fold the wiper arm backward to rest on
the windshield.
Make sure you hold on to the wiper arm
when folding it back.
!Never open the hood when the wiper
arms are folded forward.
Hold on to the wiper when folding the
wiper arm back. If released, the force
of the impact from the tensioning
spring could crack the windshield.
Do not allow the wiper arms to contact
the windshield glass without a wiper
blade inserted.
Make sure the wiper blades are proper-
ly installed. Improperly installed wiper
blades may cause windshield damage.
For your convenience, you should have
this work carried out by an authorized
Mercedes-Benz Center.

422 Practical hintsBatteryDisconnecting the battery
1Water tray
2Lock

Pull up parking brake lever firmly and
m o v e g e a r s e l e c t o r l e v e r * t o p o s i t i o nP
(manual transmission to Neutral).

Switch off all electrical consumers.

Remove SmartKey from starter switch.

Open the hood (
page 307).

Turn locks2 one quarter turn.

Remove water tray1.

Read and observe safety instructions
and precautions (
page 421).

Use a 10 mm open-end wrench to dis-
connect the negative lead from battery
negative terminal3 (
page 421).

Remove the cover from the positive
terminal.

Use a 10 mm open-end wrench to dis-
connect the positive lead from battery
positive terminal2 (
page 421).
Removing the battery
Remove the screw on the swivel bar.

Remove the swivel bar.

Pull out the battery ventilation tube
from the battery (depending on battery
arrangement in your vehicle model, the
ventilation tube is located either on the
left or right side of the battery).

Take out the battery.
Warning!
G
With a disconnected battery

you will no longer be able to turn the
SmartKey in the starter switch


automatic transmission*: the gear se-
lector lever will remain locked in
positionP

425 Practical hints
Jump starting

Make sure the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift gear selector lever* to positionP
(manual transmission to Neutral).

Open the hood (
page 307).

Flip up cover from positive under hood
terminal2 in front of water tray1
(page 422).1Positive terminal of charged battery
2Positive under hood terminal in front of
water tray
3Negative under hood terminal in front
of water tray
4Negative terminal of charged battery

Connect positive terminal1 of the
charged battery with positive under
hood terminal2 in front of the water
tray with one jumper cable. Clamp the
cable to positive terminal1 of the
charged battery first.

Start the engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminal4 of the
charged battery with negative under
hood terminal3 in front of the water
tray with the second jumper cable.
Clamp the cable to negative
terminal4 of the charged battery
first.

Start the engine of the disabled vehi-
cle.
You can now turn on the electrical con-
sumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
negative terminals3 and4 and then
from positive terminals2 and1.
You can now turn on the lights.

Have the battery checked at the near-
est authorized Mercedes-Benz Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 314).
!Never invert the terminal connections.
iVehicles with automatic transmission*:
Do not tow-start vehicle.

432 Practical hintsFusesFuse box in engine compartment
The fuse box is located in the engine com-
partment on the driver’s side.
1Fuse box
2Clamp
3Fuse box coverOpening

Open the hood (
page 307).

With a dry cloth, remove any moisture
from the fuse box.

Release clamps2.

Remove fuse box cover3.Closing

Make sure the sealing rubber is proper-
ly positioned.

Press fuse box cover3 down and se-
cure with clamps2.