seats MERCEDES-BENZ SLR CLASS 2005 Owners Manual

Contents
Introduction....................................... 12
Product information ............................. 13
Operator’s Manual ............................... 14
Service and warranty information .. 14
Important notice for California
retail buyers and lessees of
Mercedes-Benz automobiles .......... 15
Maintenance .................................. 16
Roadside Assistance ...................... 16
Change of address or ownership.... 16
Operating your vehicle outside
the USA or Canada......................... 17
Mercedes-Benz SLR McLaren
compliance .................................... 17
Where to find it .................................... 18
Symbols ............................................... 19
Operating safety .................................. 20
Proper use of the vehicle ............... 20
Problems with your vehicle .................. 21
Reporting safety defects...................... 22
Reporting safety defects ................ 22
Vehicle data recording......................... 23
Information regarding electronic
recording devices........................... 23
At a glance.......................................... 24
Cockpit ................................................. 26
Instrument cluster ................................ 28
Multifunction steering wheel ................ 30
Center console ..................................... 31
Upper part ...................................... 31
Lower part ...................................... 32
Overhead control panel ........................ 33
Control panel on the door sill ............... 34
Getting started................................... 36
Unlocking ............................................. 38
Starter switch positions .................. 40
Adjusting .............................................. 41
Seats .............................................. 41
Steering wheel ................................ 42
Mirrors ............................................ 43
Driving .................................................. 45
Fastening the seat belts ................. 45
Starting the engine ......................... 48
Switching on the headlamps........... 51
Turn signals .................................... 52
Windshield wipers ........................... 52
Problems while driving.................... 54
Parking and locking .............................. 56
Parking brake ................................. 56
Switching off headlamps................. 57
Turning off the engine ..................... 58

41 Getting started
Adjusting
Adjusting
SeatsThe seat adjustment switch is located on
the door sill.
1Seat fore and aft adjustment
2Seat height
3Seat angleWarning!
G
All seat, steering wheel, and rear view mirror
adjustments, as well as fastening of seat
belts, must be done before the vehicle is put
into motion.Warning!
G
Do not adjust the driver’s seat while driving.
Adjusting the seat while driving could cause
the driver to lose control of the vehicle.
Never place hands under the seat or near
any moving parts while a seat is being ad-
justed.
Never ride in a moving vehicle with the seat
back in an excessively reclined position as
this can be dangerous. You could slide un-
der the seat belt in a collision. If you slide
under it, the belt would apply force at the ab-
domen or neck.
That could cause serious or fatal injuries.
The seat back and seat belts provide the
best restraint when the wearer is in a nearly
upright position and belts are properly posi-
tioned on the body. Your seat must be ad-
justed so that you can correctly fasten your
seat belt (
page 45).
Warning!
G
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle.
Even with the SmartKey removed from the
starter switch or the vehicle, the seats can
be operated. Therefore, do not leave chil-
dren unattended in the vehicle, or with ac-
cess to an unlocked vehicle. Unsupervised
use of vehicle equipment may cause an ac-
cident and/or serious personal injury.

47 Getting started
Driving

Pull the belt smoothly from seat belt
holder 1.

Place the shoulder portion of the belt
across the top of your shoulder and the
lap portion across your hips.

Push latch plate2 into buckle3 until
it clicks.

If necessary, tighten the lap portion to
a snug fit by pulling shoulder portion
up.
Proper use of seat belts


Do not twist the belt when fastening.


Adjust seat belt so that the shoulder
portion is located as close as possible
to the middle of the shoulder (it should
not touch the neck). Never pass the
shoulder portion of the belt under your
arm.


Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.


Place the seat backrest in a nearly up-
right position.


Never use a seat belt for more than one
person at a time.


Do not fasten a seat belt around a per-
son and another object at the same
time. When using a seat belt to secure
infant or toddler restraints or children
in booster seats, always follow the
child seat manufacturer’s instructions.


Check your seat belt during travel to
make sure that it is properly
positioned.


Make sure that the seat belt is always
fitted snugly. Take special care of this
when wearing loose clothing.
Warning!
G
Do not pass belts over sharp edges. They
could tear.
Do not allow the belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the belts.
Do not bleach or dye seat belts as this may
severely weaken them. In a crash, they may
not be able to provide adequate protection.
Damaged seat belts or belts that were highly
stressed in an accident must be replaced.
Contact an authorized Mercedes-Benz
Center.

62 Safety and SecurityOccupant safetyIn this section you will learn the most im-
portant facts about the restraint systems
of the vehicle.
The restraint systems are

Seat belts


Emergency tensioning device


Airbags


Child seats


Child seat recognition
As independent systems, their protective
effects work in conjunction with each
other.The 1 indicator lamp in the instrument
cluster comes on


for about four seconds when you turn
the SmartKey in the starter switch to
position 1. It then goes out briefly,
comes on again and remains lit until
you start the engine or turn the
SmartKey to position 2.


for about four seconds when you turn
the SmartKey in the starter switch to
position 2.


for about four seconds when you start
the engine using the start button
(page 48).
The 1 indicator lamp goes out shortly
after you start the engine. This shows that
the restraint systems are operational.A malfunction in the system has been
detected if the 1 indicator lamp


fails to go out after approximately four
seconds


does not come on at all


comes on after the engine was started
or while driving
For more information, see the “Practical
hints” section (
page 302).
iFor information on infants and children
traveling with you in the vehicle and re-
straint systems for infants and chil-
dren, see “Children in the vehicle”
(page 72).

72 Safety and SecurityOccupant safetyEmergency tensioning device (ETD),
seat belt force limiter
The seat belts are equipped with
emergency tensioning devices and belt
force limiters.
The ETD is designed to activate in the
following cases when the seat belts are
fastened:

in frontal or rear-end impacts exceed-
ing a preset severity level


if the restraint systems are operational
and functioning correctly, see 1 in-
dicator lamp (
page 62).
In an impact, emergency tensioning devic-
es remove slack from the belts in such a
way that the seat belts fit more snugly
against the body. Belt force limiters reduce
the force exerted by the seat belts on
occupants during a crash.
Children in the vehicle
If an infant or child is traveling with you in
the vehicle:

Secure the child using an infant or child
restraint appropriate to the age and
size of the child.


Make sure the infant or child is proper-
ly secured at all times while the vehicle
is in motion.
Infant and child restraint seats and infor-
mation on choosing an appropriate re-
straint system can be obtained from any
Mercedes-Benz Center.
Warning!
G
An emergency tensioning device (ETD) that
was activated must be replaced.
When disposing of the emergency tension-
ing device, our safety instructions must be
followed. These are available at your autho-
rized Mercedes-Benz Center.!Do not place objects heavier than
20 lbs (9 kg) on the front passenger
seat. This could cause the front or side
impact airbag on the passenger side
and, with the seat belt fastened to se-
cure the object, the ETD to deploy in a
crash which exceeds the system’s de-
ployment threshold.

75 Safety and Security
Occupant safety
BabySmart
TM1
airbag deactivation
system
1PASSENGER AIRBAG OFF indicator
lamp
Special BabySmart
TM compatible child
seats, designed for use with the
Mercedes-Benz system and available at
any authorized Mercedes-Benz Center, are
required for use with the BabySmart
TM air-
bag deactivation system. With the special
child seat properly installed, the passenger
front airbag and the passenger knee airbag
will not deploy.The PASSENGER AIRBAG OFF indicator
lamp1 located on the lower part of the
center console will be illuminated, except
with the SmartKey removed or in starter
switch position0.Self-test BabySmart
TM
without special
child seat installed
After turning the SmartKey in the starter
switch to position1 or2, the PASSENGER
AIRBAG OFF indicator lamp comes on for
approximately six seconds and then goes
out.
If the PASSENGER AIRBAG OFF indicator
lamp should not come on or is continuous-
ly lit, the system is not functioning. You
must see an authorized Mercedes-Benz
Center before seating any child on the
front passenger seat.
1BabySmart
TM is a trademark of Siemens
Automotive Corp.
iThe system does not deactivate the
head-thorax airbag and the emergency
tensioning device.

76 Safety and SecurityOccupant safetyWarning!
G
The BabySmart
TM1
airbag deactivation sys-
tem will ONLY work with a special child seat
designed to operate with it. It will not work
with child seats which are not BabySmart
TM
compatible.
Never place anything between seat cushion
and child seat (e.g. pillow), since it reduces
the effectiveness of the deactivation sys-
tem. The bottom of the child seat must
make full contact with the passenger seat
cushion. An incorrectly mounted child seat
could cause injuries to the child in case of an
accident, instead of protecting the child.
Follow the manufacturer’s instructions for
installation of special child seats.
1BabySmart
TM is a trademark of Siemens
Automotive Corp.
Warning!
G
When using a BabySmart
TM compatible
child seat on the passenger seat, the pas-
senger front airbag will not deploy only if the
PASSENGER AIRBAG OFF indicator lamp
(
page 75) remains illuminated.
Please be sure to check the PASSENGER
AIRBAG OFF indicator lamp every time you
use the special system child seat. Should
the PASSENGER AIRBAG OFF indicator lamp
go out while the restraint is installed, please
check installation. If the PASSENGER AIR-
BAG OFF indicator lamp remains out, do not
use the BabySmart
TM restraint to transport
children on the passenger seat until the sys-
tem has been repaired.
Warning!
G
Do not place powered-on laptops, cell
phones and like electronic devices on the
front passenger seat. Signals from such de-
vices may interfere with the BabySmart
TM
system. Such signal interference may cause
the PASSENGER AIRBAG OFF indicator lamp
(
page 75) not to come on during self-test
or be continuously lit, indicating that the
system is not functioning.

278 OperationTires and wheelsTire ply material
1Plies in sidewall
2Plies under tread
This marking tells you about the type of
cord and number of plies in the sidewall
and under the tread.
Tire and loading terminology
Accessory weight
The combined weight (in excess of those
standard items which may be replaced) of
automatic transmission, power steering,
power brakes, power windows, power
seats, radio, and heater, to the extent that
these items are available as
factory-installed equipment (whether
installed or not).
Air pressure
The amount of air inside the tire pressing
outward on each square inch of the tire.
Air pressure is expressed in pounds per
square inch (psi), or kilopascal (kPa) or
bars.
Aspect ratio
Dimensional relationship between tire
section height and section width
expressed in percentage.Bar
Another metric unit for air pressure. There
are 14.5038 pounds per square inch (psi)
to 1 bar; there are 100 kilopascals (kPa)
to 1 bar.
Bead
The tire bead contains steel wires wrapped
by steel cords that hold the tire onto the
rim.
Cold tire inflation pressure
Tire inflation pressure when your vehicle
has been sitting for at least three hours or
driven no more than one mile (1.6 km).
Curb weight
The weight of a motor vehicle with stan-
dard equipment including the maximum
capacity of fuel, oil, and coolant, and, if so
equipped, air conditioning and additional
optional equipment, but without passen-
gers and cargo.
iFor illustration purposes only. Actual
data on tires is specific to each vehicle
and may vary from data shown in above
illustration.

385 Technical terms
ABS
(A
nti-lock B
raking S
ystem)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
Accessory weight
(
page 278)
ACL
(Airbrake/C
entral L
ocking)
Controls the locking mechanism of the
Airbrake and the central locking sys-
tem.
Air pressure
(
page 278)
Aspect ratio
(page 278)BabySmart
TM1
airbag deactivation
system
This system detects if a special system
compatible child restraint seat is in-
stalled on the front passenger seat. The
system will automatically deactivate
the passenger front airbag when such a
seat is properly installed (PASSENGER
AIRBAG OFF warning lamp on the lower
centre console lights up).
BabySmart
TM
compatible child seats
Special restraint system for children.
The sensor system for the passenger
seat prevents deployment of the pas-
senger front airbag if a BabySmart
TM
compatible child seat is installed. See
an authorized Mercedes-Benz Center
for availability.
Bar
(
page 278)BAS
(B
rake As
sist S
ystem)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bead
(
page 278)
Bi-Xenon headlamps
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(Customer A
ssistance C
enter)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a break-
down.
1BabySmart
TM is a trademark of Siemens
Automotive Corp.

391 Index
A
ABS 79, 385
Indicator lamp 29, 297
Messages in the multifunction
display 306
ABS/ESP
Warning lamp 29, 296
Accelerator position, automatic
transmission 173
Accessory weight 278
Accident
In case of 55
ACL 385
Messages in the multifunction
display 308
Activating
Air circulation mode 188
Air conditioning (cooling) 192
Anti-theft alarm system 91
Central locking (control system) 135
ESP 84
Exterior headlamps 51
Exterior lamps 106
Headlamps 51
High beams 109
Immobilizer 58, 90Manual gearshift program 175
Rear window defroster 181
Residual heat 190
Tow-away alarm 92
Windshield wipers 53
Adding
Coolant 249
Engine oil 248
Additional turn signals (exterior
mirror) 347
Adjusting
Air distribution 187
Air volume 186
Mirrors 43
Seat angle 42
Seat fore and aft 42
Seat height 42
Seats 41
Steering column height 43
Steering column length 43
Steering wheel 42
Air conditioner refrigerant 377
Air conditioning (cooling)
Turning off 192
Turning on 192
Air pressure 278Air pressure see Tire inflation pressure
Air recirculation mode 188
Air volume adjustment 186
Airbags 63
Children 64
Front 68
Head-thorax 68, 69
Knee 68
Passenger 68
Airbrake 31, 87
Automatic mode 89
Emergency braking 89
Manual mode 88
Message in the multifunction
display 318
Test Mode 88
Warning lamp 29, 301
Alarm
Audible 78, 90
Canceling 91, 93
Visual 90
Anticorrosion/antifreeze 376, 381
Antiglare
Automatic 179