stop start MERCEDES-BENZ SLR CLASS 2007 User Guide

171 Controls in detail
Automatic transmission
Gear selector lever positions
Effect
ìPark position
Gear selector lever position
when the vehicle is parked. Place
gear selector lever in park
positionP only when vehicle is
stopped. The park position is not
intended to serve as a brake
when the vehicle is parked.
Rather, the driver should always
set the parking brake in addition
to placing the gear selector lever
in park positionP to secure the
vehicle.
The SmartKey can only be
removed from the starter switch
with the gear selector lever in
park positionP. With the
SmartKey removed, the gear
selector lever is locked in park
positionP.
Effect
íReverse gear
Place gear selector lever in
positionR only when vehicle is
stopped.
Effect
ëNeutral
No power is transmitted from the
engine to the drive axle. When
the brakes are released, the
vehicle can be moved freely
(pushed or towed).
To avoid damage to the trans-
mission, never engageN while
driving.
If the ESP
® is deactivated or
malfunctioning:
Move gear selector lever to
neutralN only if the vehicle is in
danger of skidding, e.g. on icy
roads.
êDrive position
The transmission shifts
automatically. All five forward
gears are available.

175 Controls in detail
Automatic transmission
Shift program mode selector switch
1Program mode selector switch
C Comfort For comfort driving
MAN Manual For manual gear shifting
(
page 179)
S Sport For standard driving
The selected shift program appears in the
right multifunction display (
page 117).
Turn the program mode selector switch
to the desired setting.
The letter of the desired shift program
appears in the right multifunction
display.
Select C for comfort driving:

The vehicle starts out in second
gear for gentler starts. This does
not apply if full throttle is applied or
gear range1 is selected.

Traction and driving stability are
improved on icy roads.

Upshifts occur earlier even when
you give more gas. The engine then
operates at lower rpms and the
wheels are less likely to spin.Gear selector lever one-touch
gearshifting
With the gear selector lever in drive posi-
tion D and driving in shift programC orS,
you can limit or extend the gear range.
With the MAN shift program activated, you
can use the gear selector lever to manually
shift the gears.
The following instructions describe opera-
tion of the gear selector lever when driving
in the shift programC orS.
!Never change the program when the gear
selector lever is out of park positionP. This could
result in a change of driving characteristics for
which you may not be prepared.
iFor information on using the gear selector
lever in shift program MAN, see “Manual shift
program” (
page 179).
!Allow engine to warm up under low load use.
Do not place full load on the engine until the
operating temperature has been reached.
Shift into reverse gearR or park positionP only
when the vehicle is stopped.
Avoid spinning of a drive wheel for an extended
period when driving off on slippery road
surfaces. This may cause serious damage to the
drivetrain which is not covered by the
Mercedes-Benz Limited Warranty.

181 Controls in detail
Automatic transmission
Emergency operation
(Limp-Home Mode)
If vehicle acceleration becomes less re-
sponsive or sluggish or the transmission
no longer shifts, the transmission is most
likely operating in limp-home (emergency
operation) mode. In this mode only second
gear and reverse gear can be activated.
Stop the vehicle in a safe location.
Move gear selector lever to park
positionP.
Turn off the engine.
Wait at least 10 seconds before
restarting.
Restart the engine.
Move gear selector lever to drive
positionD (for second gear) or
positionR.
Have the transmission checked at an
authorized Mercedes-Benz Center as
soon as possible.

197 Controls in detail
Automatic climate control
Deactivating
It is possible to deactivate the cooling
function of the automatic climate control
system. The air in the vehicle will then no
longer be cooled or dehumidified.
Press ± button (page 188).
The indicator lamp on the ±
button comes on. The cooling function
switches off after a short delay.Activating
Moist air can fog up the windows. You can
dehumidify the air with the air
conditioning.
Press ± button again (page 188).
The indicator lamp on the ± button
goes out.
The air conditioning uses the refrigerant
R134A. This refrigerant is free of CFCs
which are harmful to the ozone layer.
Residual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.
iUnder certain circumstances, e.g. when the
fuel system is too hot and needs to be cooled,
the cooling switches on again automatically. The
red lamp on the ± button the automatic
climate control panel flashes.
After cooling the fuel system sufficiently, the air
conditioning switches off again and the red lamp
stops flashing.
!If you press the ± button on the auto-
matic climate control panel and it starts to flash,
this indicates that the air conditioning is losing
refrigerant. The compressor has turned off. The
air conditioning cannot be turned on again.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.
iHow long the system will provide heating
depends on the coolant temperature and the
selected temperature. The blower will run at low
speed regardless of the air distribution control
setting.

199 Controls in detail
Power windows
Power windows
Opening and closing the windows
The door windows are opened and closed
electrically. The switches for the windows
are located on the door sill on the driver’s
side (
page 34). The switch for the pas-
senger side is located on the door sill on
the passenger side.
1Left window
2Right window
Switch on the ignition (page 40).
Warning!G
When closing the windows, make sure there
is no danger of anyone being harmed by the
closing procedure.
The closing of the windows can be immedi-
ately halted by releasing the switch or, if
switch was pulled past the resistance point
and released, by either pressing or pulling
the respective switch.
If the window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the window,
the automatic reversal function will stop the
window and open it slightly.
If the window encounters an obstruction
that blocks its path in a circumstance where
you are closing the window by pulling and
holding the switch, or by pressing and hold-
ing button‹ on the SmartKey, or by
pressing and holding the ,button on the
climate control panel, the automatic
reversal function will not operate.
When leaving the vehicle, always remove the
SmartKey from starter switch, take it with
you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.
iDepending on the current position, the win-
dows may also open or close when the air recir-
culation button, on the control panel of the
automatic climate control (
page 188) is
pressed and held.
iAfter switching off the ignition (page 40)
or removing the SmartKey from the starter
switch, the windows can be operated

until you open a door

for at least 5 minutes if no door was opened

308 Practical hints
What to do if ...
ProblemPossible cause/consequenceSuggested solution
on for a maximum of 6 seconds
after starting the engine.The telltale reminds you and your passenger
to fasten your seat belts before driving off.Fasten your seat belts.
Regardless of whether the seat belts
are fastened or not, the seat belt tell-
tale always comes on and remains lit
for 6 seconds after starting the
engine.
maximum of 6 seconds after
starting the engine.You have forgotten to fasten your seat belt.Fasten your seat belt.
The warning chime stops sounding.
on while the vehicle is standing
still and the engine is running or
during driving.You and/or your passenger have forgotten to
fasten your seat belts.Fasten your seat belts.
The seat belt telltale goes out.
There are items placed on the passenger seat
and therefore the system senses the passen-
ger seat as being occupied.Remove the items from the passenger
seat and put them in a safe place.
The seat belt telltale goes out.

328 Practical hints
What to do if ...
Left displayRight displayPossible cause/
consequencePossible solution
#The battery is no longer
charging. Possible causes:

alternator malfunctioning

broken poly-V-belt
Do not forget that the brake
system requires electrical
energy and may be operating
with restricted capability.
Considerably greater brake
pedal force is required and the
pedal travel is longer. The stop-
ping distance is increased. If
necessary, apply full pressure
to the brake pedal.
Stop the vehicle immediately in a safe location and
check the poly-V-belt.
If it is broken:
Do not continue to drive. Otherwise, the engine will
overheat due to an inoperative water pump which
may result in damage to the engine. Contact an
authorized Mercedes-Benz Center.
If it is in order:
Contact an authorized Mercedes-Benz Center imme-
diately. Adjust driving to be consistent with reduced
braking responsiveness.
Read and observe additional messages in the
multifunction display.
The starter battery has been
charged with a battery charger
or jump started.Contact an authorized Mercedes-Benz Center.
There is a malfunction in the
electronic system.Have the system checked at an authorized
Mercedes-Benz Center immediately.

332 Practical hints
What to do if ...
Left displayRight displayPossible cause/
consequencePossible solution
;(USA only)
3(Canada only)
Reduced
brake effect
Start engineThe battery has insufficient
voltage and cannot supply
sufficient power to the
electro-hydraulic brake system.
Considerably greater brake
pedal force is required and the
pedal travel is longer. The
stopping distance is increased.Start the engine.
As soon as the engine is running, the message
disappears.
Increased
stopping distance
Start engine
Warning!G
Inhalation of exhaust gas is hazardous to
your health. All exhaust gas contains carbon
monoxide (CO), and inhaling it can cause
unconsciousness and possible death.
Do not run the engine in confined areas
(such as a garage) which are not properly
ventilated.

336 Practical hints
What to do if ...
Left displayRight displayPossible cause/
consequencePossible solution
•Coolant
Stop car –

Turn engine off
The coolant is too hot.
Among other possible causes,
the poly-V-belt could be
broken.Stop the vehicle in a safe location or as soon as it is safe to
do so.
Turn off the engine.
Check the poly-V-belt.
If it is broken:
Do not continue to drive. Otherwise, the engine will over-
heat due to an inoperative water pump which may result in
damage to the engine. Contact an authorized
Mercedes-Benz Center.
If it is intact:
Wait for the message to disappear before restarting the
engine.
Doing otherwise could result in serious engine damage that
is not covered by the Mercedes-Benz Limited Warranty.
(Continued on next page)

355 Practical hints
Unlocking in an emergency
Unlocking in an emergency
Unlocking the vehicle
Unlocking the trunk
If you cannot unlock the trunk with the
SmartKey, open the trunk with the
mechanical key.
The handle is located above the rear
license plate recess.1Mechanical key locking tab
2Mechanical key
Press locking tab1 in the direction of
arrow and, at the same time, remove
mechanical key2 completely out of
the housing.
Trunk lid lock
3Unlocking
Insert the mechanical key in the trunk
lid lock.
Perform the following two steps
simultaneously:
Turn the mechanical key
counterclockwise to the stop, to
position3.
Pull the trunk lid handle and lift the
trunk lid.
iUnlocking the trunk with the mechanical key
will trigger the anti-theft alarm system when the
door is opened.
To cancel the alarm, insert the SmartKey in the
starter switch.