warning light MERCEDES-BENZ SLR CLASS 2007 Owner's Manual

200 Controls in detail
Power windows
Opening the windows
Press switch1 or2 to the resistance
point.
The corresponding window will move
downwards until you release the
switch.
Closing the windows
Pull switch1 or2 to the resistance
point.
The corresponding window will move
upwards until you release the switch.Fully opening the windows
(Express-open)
Press switch1 or2 past the
resistance point and release.
The corresponding window opens
completely.
Fully closing the windows
(Express-close)
Pull switch1 or2 past the
resistance point and release.
The corresponding window closes
completely.Stopping the windows
Press or pull respective switch again.
Warning!G
If you pull and hold the switch up when
closing the window, and upward movement
of the window is blocked by some obstruc-
tion including but not limited to arms, hands,
fingers, etc., the automatic reversal will not
operate.
Warning!G
Driver’s door only:
If within 5 seconds you again pull the switch
past the resistance point and release, the
automatic reversal will not function.
!If the upward movement of the window is
blocked during the closing procedure, the
window will stop and open slightly.
Remove the obstruction, pull the switch again
past the resistance point and release.
If the window still does not close when there is
no obstruction, then pull and hold the switch
again. The window will then close without the
obstruction sensor function.

208 Controls in detail
Useful features
Ashtray and cigarette lighter
The ashtray and the cigarette lighter are lo-
cated in the storage compartment under
the armrest.
1Cigarette lighter
2Ashtray insertAshtray
Removing ashtray insert
Pull ashtray insert2 upwards.
Replacing ashtray insert
Press the ashtray insert into the holder
until you hear it click into place.Cigarette lighter
Switch on the ignition (page 40).
Push in cigarette lighter 1.
The cigarette lighter pops out automat-
ically when hot.
Warning!G
Remove ashtray insert only with vehicle
standing still.
Warning!G
Never touch the heating element or sides of
the lighter; they are extremely hot. Hold the
knob only.
Make sure that any children traveling with
you do not injure themselves or start a fire
with the hot cigarette lighter.
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.

209 Controls in detail
Useful features
Power outlet
The power outlet is located on the left side
in the trunk.
1Power outlet
Switch on the ignition (page 40).
Flip up cover and insert electrical plug
(cigar lighter type).
Telephone
The telephone is located in the center
storage compartment (
page 207).
!The lighter socket can accommodate
12V DC electrical accessories (up to a maximum
of 85 W) designed for use with the standard
“cigarette lighter” plug type. Keep in mind, how-
ever, that connecting accessories to the lighter
socket (for example extensive connecting and
disconnecting, or using plugs that do not fit prop-
erly) can damage the lighter socket. With the
socket damaged, the lighter may no longer be
able to be placed in the heating (pushed-in) posi-
tion, or the lighter may pop out too early with the
lighter not hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with a stan-
dard “cigarette lighter” plug type to the
12 V power outlets in your vehicle whenever
possible.
iThe power outlet can be used to accommo-
date 12V DC electrical accessories (e.g. air
pump, auxiliary lamps) up to a maximum
of 180 W or as a battery charging point
(
page 368).
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and personal
injury.

242 Operation
Driving instructions
Winter driving instructions
The most important rule for slippery or icy
roads is to drive sensibly and to avoid
abrupt acceleration, braking and steering
maneuvers. Do not use the cruise control
system under such conditions.
When the vehicle is in danger of skidding,
move gear selector lever to neutral
positionN. Try to keep the vehicle under
control by corrective steering action.Road salts and chemicals can adversely
affect braking efficiency. Increased pedal
force may become necessary to produce
the normal braking effect.
Depressing the brake pedal periodically
when traveling at length on salt-strewn
roads can bring road-salt-impaired braking
efficiency back to normal.
If the vehicle is parked after being driven
on salt-treated roads, the braking
efficiency should be tested as soon as
possible after driving is resumed.
For more information, see “Winter driving”
(
page 290).
iFor information on driving with snow chains,
see “Snow chains” (
page 291).
Warning!G
On slippery road surfaces, never downshift
in order to obtain braking action. This could
result in drive wheel slip and reduced
vehicle control. Your vehicle’s ABS will not
prevent this type of control loss.
Warning!G
Make sure not to endanger any other road
users when carrying out these braking
maneuvers.
Warning!G
If the vehicle becomes stuck in snow, make
sure snow is kept clear of the exhaust pipe
and from around the vehicle with the engine
running. Otherwise deadly carbon monoxide
(CO) gases may enter vehicle interior
resulting in unconsciousness and death.
To assure sufficient fresh air ventilation,
open a window slightly on the side of the
vehicle not facing the wind.
Warning!G
The outside temperature indicator is not
designed to serve as an ice-warning device
and is therefore unsuitable for that purpose.
Indicated temperatures just above the
freezing point do not guarantee that the
road surface is free of ice.

261 Operation
Tires and wheels
Storing tires
Cleaning tiresDirection of rotation
Unidirectional tires offer added advan-
tages, such as better hydroplaning perfor-
mance. To benefit, however, you must
make sure the tires rotate in the direction
specified.
An arrow on the sidewall indicates the
intended direction of rotation (spinning) of
the tire.Loading the vehicle
Two labels on your vehicle show how much
weight it may properly carry.
1) The Tire and Loading Information
placard can be found on the driver’s
door B-pillar. This placard tells you im-
portant information about the number
of people that can be in the vehicle and
the total weight that can be carried in
the vehicle. It also contains information
on the proper size and recommended
tire inflation pressures for the original
equipment tires on your vehicle.
!Keep unmounted tires in a cool, dry place
with as little exposure to light as possible.
Protect tires from contact with oil, grease and
gasoline.
!Never use a round nozzle to power wash
tires. The intense jet of water can result in
damage to the tire.
Always replace a damaged tire.
Warning!G
Have worn or damaged tires replaced in
pairs (front pair or rear pair) an make sure
the tires rotate in the direction specified
(
page 261). Otherwise, the driving stabili-
ty of the vehicle will be adversely affected,
especially when driving at high speeds.
Warning!G
19" turbine-style wheels:
The wheels must be mounted corresponding
to the labelling on the inside of the rim,
where LEFT refers to the left-hand side of
the vehicle and RIGHT to the right-hand side
of the vehicle, both seen in direction of trav-
el. When unidirectional tires are mounted,
make sure that they rotate in the direction
specified. Otherwise, the driving stability of
the vehicle will be adversely affected,
especially when driving at high speeds.

364 Practical hints
Flat tire
Screw filler hosea onto tire valve7.
Close vent screw9 on pressure
gauge.
Insert electrical plug4 into vehicle
cigarette lighter socket.
Turn the SmartKey in the starter switch
to position1 (
page 40).
PressI on electric air pump switch8.
The electric air pump should now
switch on and inflate the tire.After 5 minutes, the pressure gauge must
display at least 26 psi (1.8 bar). The air
hose can become hot during inflation.
Please exercise appropriate caution.
If this tire inflation pressure is not at-
tained, turn off the electric air pump,
detach the filler hose from the tire
valve, and drive vehicle back and forth
very slowly approximately 30 ft (10 m).
This serves to better distribute the
TIREFIT sealant material inside the tire.
Unscrew the air pump’s air hose5
from flange6 of the TIREFIT
container.
Screw air hose5onto tire valve7.
Inflate the tire again.
After attaining a tire inflation pressure
of 26 psi (1.8 bar), press0 on electric
air pump switch8.
The electric air pump should now be
switched off.
Turn the SmartKey in the starter switch
to position0 (
page 40).
Detach the electric air pump.
The air hose may still be hot. Please
exercise appropriate caution.
!Do not operate the electric air pump longer
than 8 minutes without interruption. Otherwise it
may overheat.
You may operate the air pump again after it has
cooled off.
Warning!G
If a tire inflation pressure of 26 psi (1.8 bar)
is not attained, the tire is too severely
damaged for TIREFIT to provide a reliable
tire repair.
In this case, TIREFIT cannot properly seal
the tire.
Do not drive the vehicle.
Contact the nearest Mercedes-Benz Center
or call Roadside Assistance.


392 Technical data
Fuels, coolants, lubricants, etc.
Brake fluid
Only brake fluid approved by
Mercedes-Benz is recommended. Your
authorized Mercedes-Benz Center will
provide you with additional information.Premium unleaded gasoline
Warning!G
During vehicle operation, the boiling point of
the brake fluid is continuously reduced
through the absorption of moisture from the
atmosphere. Under extremely strenuous
operating conditions, this moisture content
can lead to the formation of bubbles in the
system, thus reducing the system’s
efficiency.
Therefore, the brake fluid must be replaced
regularly. Refer to your vehicle’s Mainte-
nance Booklet for replacement interval.
Warning!G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
personal injury.
Never allow sparks, flame or smoking
materials near gasoline!
Turn off the engine before refueling.
Whenever you are around gasoline, avoid
inhaling fumes and skin or cloth contact,
extinguish all smoking materials.
Direct skin contact with fuels and the
inhalation of fuel vapors can damage your
health.
!To maintain the engine’s durability and per-
formance, premium unleaded gasoline must be
used. If premium unleaded is not available and
low octane fuel is used, follow these precau-
tions:

Have the fuel tank only partially filled with
unleaded regular gasoline and fill up with
premium unleaded gasoline as soon as
possible.

Avoid full throttle driving and abrupt acceler-
ation.

Do not exceed an engine speed of 3000 rpm
if the vehicle is loaded with a light load such
as two persons and no luggage.

Do not exceed 2/3 of maximum accelerator
pedal position if the vehicle is fully loaded or
operating in mountainous terrain.

399 Technical terms
ABS
(A
nti-lock Braking System)
Prevents the wheels from locking up
during braking so that the vehicle can
continue to be steered.
Accessory weight
(
page 284)
ACL
(A
irbrake/Central Locking)
Controls the locking mechanism of the
Airbrake and the central locking
system.
Air pressure
(
page 284)
Aspect ratio
(
page 284)
Bar
(
page 284)BAS
(B
rake Assist System)
System for potentially reducing braking
distances in emergency braking situa-
tions. The system is activated when it
senses an emergency based on how
fast the brake is applied.
Bead
(
page 284)
Bi-Xenon headlamps
Headlamps which use an electric arc as
the light source and produce a more in-
tense light than filament headlamps.
Bi-Xenon headlamps produce low
beam and high beam.
CAC
(C
ustomer Assistance Center)
Mercedes-Benz customer service cen-
ter, which can help you with any ques-
tions about your vehicle and provide
assistance in the event of a
breakdown.CAN system
(C
ontroller Area Network)
Data bus network serving to control
vehicle functions such as door locking
or windshield wiping depending on
vehicle settings and/or ambient
conditions.
Cockpit
All instruments, switches, buttons and
indicator/warning lamps in the passen-
ger compartment needed for vehicle
operation and monitoring.
Cold tire inflation pressure
(
page 284)
Control system
The control system is used to call up
vehicle information and to change
component settings. Information and
messages appear in the multifunction
display. The driver uses the buttons on
the multifunction steering wheel to
navigate through the system and to
adjust settings.

408 Index
Central locking
Automatic 104, 139
Central locking switch 31
Locking/unlocking from inside 105
Central locking switch 105
Child restraints 60
Children in the vehicle 75
Air bags 63
Indicator lamp, passenger front air
bag 70
Infant and child restraint systems 60,
70, 78
Occupant Classification System
(OCS) 67
Passenger front air bag off indicator
lamp 70, 312
Cigarette lighter 208
Clock 29, 133
Setting time 134
Closed circuit racing
Brakes 238
Cockpit 26, 399Cold tire inflation pressure 284
Combination switch 27, 51, 110
Compact guide 354
Control and operation of radio
transmitters 243
Control system 117, 399
Multifunction display 117
Multifunction steering wheel 118
Control system menus 120
722 Edition menu 123
AUDIO menu 126
Settings menu 129
Standard display menu 122
TEL menu 141
Trip computer menu 139
Vehicle status message memory
menu 128
Control system submenus 121, 130
Instrument cluster 132
Lighting 134
Time 133
Vehicle 138Controller Area Network see CAN
Coolant 248, 255, 394
Anticorrosion/antifreeze mixing ratio
and quantity 396
Capacities 390
Checking coolant level 248, 255
Messages in the multifunction
display 335
Temperature 245
Temperature gauge 115
Warning lamp 29, 306
Courtesy lighting 113
Cruise control 27, 203, 400
Messages in the multifunction
display 317
Curb weight 284
Customer Assistance Center see CAC

412 Index
Gear selector lever one-touch gearshifting
Automatic transmission 175
Gearshift
Indicator lamp 29
Program, Manual 175, 179
Global locking/unlocking see Key
Good visibility 182
GPS 400
Gross Axle Weight Rating see GAWR
Gross Vehicle Weight Rating see GVWR
Gross Vehicle Weight see GVW
GVW 284
GVWR 285
H
Hands-free microphone 33
Hazard warning flasher 111
Headlamp switch-off delay see Delayed
switch-off, exterior lamps
Headlamps
Automatic headlamp mode 107
Cleaning lenses 297
Cleaning system 182, 257, 397
Manual headlamp mode 107
Messages in the multifunction
display 341Replacing bulbs 359
Switch 51, 106
Head-thorax air bag 66, 400
High beam flasher 51, 110
Replacing bulbs 359
High beam headlamps
Indicator lamp 29
Messages in the multifunction
display 341
Replacing bulbs 359
Switching on 110
High mounted brake lamp 360
High performance driving 238
High-pressure cleaners 297
Hood 250
Messages in the multifunction
display 352
Horn 27
HVAC see Automatic climate control
Hydroplaning 241I
Identification labels 378
Identification Number, Vehicle (VIN) 378
Ignition 40
Immobilizer 92
Indicator lamps see Lamps, Indicator and
warning
Infant and child restraint systems see Chil-
dren in the vehicle
Inflation pressure see Tires, Inflation pres-
sure
Inside door handle 34
Instrument cluster 28, 114, 401
Illumination brightness 114
Lamps 300
Messages in display see Multifunction
display messages
Multifunction display 117
Instrument lighting see Instrument cluster,
Illumination brightness
Instrument panel see Instrument cluster
Instruments and controls see Cockpit
Interior lighting 112
Delayed switch-off 137