heating MERCEDES-BENZ SLR CLASS 2007 Owners Manual

88 Safety and Security
Driving safety systems
The electro-hydraulic brake servo assis-
tance switches off automatically

approximately 2 minutes after you
turned the SmartKey in the starter
switch to position0 or removed the
SmartKey

approximately 20 seconds after you
locked the vehicle from the outside
Notes on driving with the
electro-hydraulic brake system

Following extended periods of only mi-
nor loads to your brake system, you
should occasionally apply the brakes
when traveling at high speeds. This im-
proves the grip of the brake pads and
prevents possible brake noise.

After driving on wet or snow-covered
roads, you should apply your brakes
firmly before parking your vehicle. This
produces heat which serves to dry the
brake disks.

On long and steep grades, shift to a
lower gear (gear range1, 2, or 3) to
prevent the brakes from overheating
and to reduce brake wear.

After hard braking, it is advisable to
drive on for some time so that the air
stream will cool down the brakes
faster.

Only Mercedes-Benz approved compo-
nents (e.g. brake pads) should be
installed on your vehicle. Brake pads
not approved by Mercedes-Benz may
impair the safety of your vehicle.
Warning!G
Have brake pad replacement and other work
on the electro-hydraulic brake system car-
ried out by qualified technicians only. Con-
tact an authorized Mercedes-Benz Center
for further information. The electro-hydrau-
lic brake system must be deactivated prior
to working on the system. High pressure is
intermittently built up in the system as part
of its automatic self-test. In addition, the
system is automatically activated when the
vehicle is unlocked by remote control, when
the driver or passenger door is opened,
when the SmartKey in the starter switch is
turned to position1, when the brake pedal
is depressed or when the parking brake is
released. Failure to deactivate the system
prior to maintenance will cause brake pis-
tons to extend and brake fluid to leak, which
may result in injuries (contusions and acid
burns). Extended brake pistons may also
cause injury.
Warning!G
Make sure not to endanger any other road
users when carrying out these braking
maneuvers.

194 Controls in detail
Automatic climate control
Front defroster
You can use this setting to defrost the
windshield, for example if it is iced up.
You can also defog the windshield and the
side windows.
Activating
Press button P (page 188).
The indicator lamp on the button
comes on.
The air conditioning switches to the
following functions automatically:

cooling on to dehumidify

maximum blower speed and
heating power

air flows onto the windshield
and the front side windows

the air recirculation mode is
switched offDeactivating
Press button P (page 188).
The indicator lamp on the button goes
out. Defrosting is turned off.
The previous settings are in effect
again.Windshield fogged on the outside
Switch the windshield wipers on
(
page 52).
If the automatic air distribution and air
volume are switched off:
Turn air distribution controls1 and 5
(
page 188) to position h ork.
or
Press control buttons 1, 5 and 9
(
page 188).
The control buttons are engaged.
TheU symbol on the control
buttons come on. Air distribution and
air volume are adjusted automatically.
iKeep this setting selected only until the
windshield or the side windows are clear again.
iThe cooling remains switched on.
iKeep this setting selected only until the
windshield is clear again.

197 Controls in detail
Automatic climate control
Deactivating
It is possible to deactivate the cooling
function of the automatic climate control
system. The air in the vehicle will then no
longer be cooled or dehumidified.
Press ± button (page 188).
The indicator lamp on the ±
button comes on. The cooling function
switches off after a short delay.Activating
Moist air can fog up the windows. You can
dehumidify the air with the air
conditioning.
Press ± button again (page 188).
The indicator lamp on the ± button
goes out.
The air conditioning uses the refrigerant
R134A. This refrigerant is free of CFCs
which are harmful to the ozone layer.
Residual heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.
iUnder certain circumstances, e.g. when the
fuel system is too hot and needs to be cooled,
the cooling switches on again automatically. The
red lamp on the ± button the automatic
climate control panel flashes.
After cooling the fuel system sufficiently, the air
conditioning switches off again and the red lamp
stops flashing.
!If you press the ± button on the auto-
matic climate control panel and it starts to flash,
this indicates that the air conditioning is losing
refrigerant. The compressor has turned off. The
air conditioning cannot be turned on again.
Have the air conditioning checked at the nearest
authorized Mercedes-Benz Center.
iHow long the system will provide heating
depends on the coolant temperature and the
selected temperature. The blower will run at low
speed regardless of the air distribution control
setting.

208 Controls in detail
Useful features
Ashtray and cigarette lighter
The ashtray and the cigarette lighter are lo-
cated in the storage compartment under
the armrest.
1Cigarette lighter
2Ashtray insertAshtray
Removing ashtray insert
Pull ashtray insert2 upwards.
Replacing ashtray insert
Press the ashtray insert into the holder
until you hear it click into place.Cigarette lighter
Switch on the ignition (page 40).
Push in cigarette lighter 1.
The cigarette lighter pops out automat-
ically when hot.
Warning!G
Remove ashtray insert only with vehicle
standing still.
Warning!G
Never touch the heating element or sides of
the lighter; they are extremely hot. Hold the
knob only.
Make sure that any children traveling with
you do not injure themselves or start a fire
with the hot cigarette lighter.
When leaving the vehicle, always remove the
SmartKey from the starter switch, take it
with you, and lock the vehicle. Do not leave
children unattended in the vehicle, or with
access to an unlocked vehicle. A child’s
unsupervised access to a vehicle could
result in an accident and/or serious
personal injury.

209 Controls in detail
Useful features
Power outlet
The power outlet is located on the left side
in the trunk.
1Power outlet
Switch on the ignition (page 40).
Flip up cover and insert electrical plug
(cigar lighter type).
Telephone
The telephone is located in the center
storage compartment (
page 207).
!The lighter socket can accommodate
12V DC electrical accessories (up to a maximum
of 85 W) designed for use with the standard
“cigarette lighter” plug type. Keep in mind, how-
ever, that connecting accessories to the lighter
socket (for example extensive connecting and
disconnecting, or using plugs that do not fit prop-
erly) can damage the lighter socket. With the
socket damaged, the lighter may no longer be
able to be placed in the heating (pushed-in) posi-
tion, or the lighter may pop out too early with the
lighter not hot enough.
To help avoid damaging the cigarette lighter
socket, we recommend connecting 12V DC elec-
trical accessories designed for use with a stan-
dard “cigarette lighter” plug type to the
12 V power outlets in your vehicle whenever
possible.
iThe power outlet can be used to accommo-
date 12V DC electrical accessories (e.g. air
pump, auxiliary lamps) up to a maximum
of 180 W or as a battery charging point
(
page 368).
Warning!G
Never operate radio transmitters equipped
with a built-in or attached antenna (i.e. with-
out being connected to an external antenna)
from inside the vehicle while the engine is
running. Doing so could lead to a malfunc-
tion of the vehicle’s electronic system, pos-
sibly resulting in an accident and personal
injury.

236 Operation
Driving instructions
Power assistanceBrakes
Warning!G
The brake system requires electrical energy
for operation.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. In such a case, the
red brake warning lamp (
page 303) and
warning messages (
page 314) in the in-
strument cluster come on while driving. To
brake, the driver must then apply signifi-
cantly greater brake pedal pressure and de-
press the pedal much further to obtain the
expected braking effect. If necessary, apply
full pressure to the brake pedal. Brakes are
only applied to the front wheels. Stopping
distance is increased! If there is a malfunc-
tion in the electro-hydraulic brake system,
we recommend that the vehicle be trans-
ported with all wheels off the ground using
flatbed or appropriate wheel lift/dolly
equipment.
A tow bar must be used if circumstances do
not permit the use of the recommended
towing methods and the vehicle requires
towing with all four wheels on the ground.
Towing the vehicle with all four wheels on
the ground is only permissible for distances
up to 30 miles (50 km) and at a speed not to
exceed 30 mph (50 km/h). For more infor-
mation, see “Towing the vehicle”
(
page 370).
With the engine not running, there is no
power assistance for the brake and steering
systems. In this case, it is important to keep
in mind that a considerably higher degree of
effort is necessary to brake and steer the
vehicle.
Warning!G
After driving in heavy rain for some time
without applying the brakes or through wa-
ter deep enough to wet brake components,
the first braking action may be somewhat
reduced and increased pedal pressure may
be necessary to obtain expected braking
effect. Maintain a safe distance from
vehicles in front.
Resting your foot on the brake pedal will
cause excessive and premature wear of the
brake pads.
It can also result in the brakes overheating
thereby significantly reducing their effec-
tiveness. It may not be possible to stop the
vehicle in sufficient time to avoid an
accident.

238 Operation
Driving instructions
Only install brake pads and brake fluid
recommended by Mercedes-Benz.
After hard braking, it is advisable to drive
on for some time, rather than to park im-
mediately, so the air stream will cool down
the brakes faster.High performance driving
The rate of wear of individual brake system
components, such as brake pads or disks,
depends on your driving style and the con-
ditions under which you operate the vehi-
cle.
It is therefore not possible to give a gener-
ally applicable service life. High perfor-
mance driving, such as driving on closed
circuit race tracks or an aggressive driving
style, will cause the brakes to wear more
quickly.
Warning!G
If other than recommended brake pads are
installed, or other than recommended brake
fluid is used, the braking properties of the
vehicle can be degraded to an extent that
safe braking is substantially impaired. This
could result in an accident.
Be certain to read and observe the warning
notices on brake pad replacement
(
page 88).
!When driving down long and steep grades,
relieve the load on the brakes by shifting into a
lower gear to use the engine’s braking power.
This helps prevent overheating of the brakes and
reduces brake pad wear.
iPlease contact your PLM or any authorized
Mercedes-Benz Center before operating the
vehicle under such demanding operating condi-
tions for more information.
Warning!G
Repetitive excessive load on the brake
system may particularly cause the brake
system to overheat and can thus reduce the
braking power, or even cause brake system
components to fail due to increased wear.
You could lose control of the vehicle and
cause an accident. Installation and examina-
tion of brake system assemblies requires
specialist knowledge. Therefore, after high
performance driving, have the brake system
checked and maintained by an authorized
Mercedes-Benz Center.

306 Practical hints
What to do if ...
During severe operating conditions, e.g.
stop-and-go traffic, the coolant tempera-
ture may rise close to 248°F (120°C).
ProblemPossible cause/consequenceSuggested solution
DThe red coolant temperature
warning lamp comes on while
the engine is running.There is insufficient coolant in the reservoir.Immediately add coolant to prevent en-
gine from overheating (
page 255).
If this warning lamp comes on frequently,
there is a leak in the cooling system.Have the cooling system checked by
an authorized Mercedes-Benz Center.
If the coolant level is correct, the electric
radiator fan may be broken. If the coolant temperature is below
248°F (120°C), you can continue driv-
ing to the nearest authorized
Mercedes-Benz Center.
Avoid high engine loads (e.g. driving
uphill) and stop-and-go driving.
DThe red coolant temperature
warning lamp comes on while
the engine is running and you
hear a warning sound.The coolant temperature has exceeded
248°F (120°C).Stop as soon as possible in a safe loca-
tion and allow the engine and coolant
to cool down.
Warning!G
Driving when your engine is overheated can
cause some fluids which may have leaked
into the engine compartment to catch fire.
You could be seriously burned.
Steam from an overheated engine can cause
serious burns which can occur just by open-
ing the engine hood. Stay away from the en-
gine if you see or hear steam coming from it.
Stop the vehicle in a safe location away from
other traffic. Turn off the engine, get out of
the vehicle and do not stand near the vehicle
until the engine has cooled down.
!The engine should not be operated with the
coolant temperature above 248°F (120°C). Do-
ing so may cause serious engine damage which
is not covered by the Mercedes-Benz Limited
Warranty.

317 Practical hints
What to do if ...
Left displayRight displayPossible cause/consequencePossible solution
ABSABS, ESP
inoperative
See
Oper. ManualRisk of accident!
The ABS and ESP
® ha ve s witc he d off
due to a malfunction.
The BAS is also deactivated.
The electro-hydraulic brake system
is still functioning normally but with-
out the ABS, the ESP
®, and the BAS
available.
Continue driving with added caution.
Wheels may lock during hard braking,
reducing steering capability.
Have the system checked at an authorized
Mercedes-Benz Center as soon as possible.
Failure to follow these instructions increases
the risk of an accident.
Convenience
functionstemporarily
unavailableThe battery for electrical consumers
has insufficient voltage and can no
longer supply the convenience func-
tions such rear window heating.As soon as the on-board voltage is sufficient,
you will see the following message in the multi-
function display:
Convenience functions
available again
. The electrical consumers are
switched on again.
Cruise control––– mph
(USA only)
––– km/h
(Canada only)
You have attempted to resume a
stored speed, but nothing is stored.Store a speed (page 204).
You have attempted to set a speed
below 20 mph (30 km/h).Accelerate to a speed exceeding
20 mph (30 km/h) and set the speed
(
page 204).
The ESP® is switched off.Switch on the ESP® (page 86).
Exceptions: (
page 85).

333 Practical hints
What to do if ...
Left displayRight displayPossible cause/
consequencePossible solution
;(USA only)
3(Canada only)
Brakes overheated
Drive on, but with
even greater careThe brake system is overheated
due to an excessive load on the
brakes.Relieve the load on the brake system.
Drive more smoothly and think ahead to avoid
unnecessary braking.
Use the engine’s braking power more frequent-
ly. Shift into a lower gear (
page 174).
Cautiously continue driving so that the air
stream will cool down the brakes.
The message disappears after driving carefully
for a few minutes.
Warning!G
Overheating of the brake system will short-
en the service life of the brake disks. The
brake disks could fail. Have the brake disks
checked at an authorized Mercedes-Benz
Center.