garage door opener Mercury Mariner 2010 Owner's Manuals

roof reaches the bounce-back position,the moon roof will travel with
no bounce-back protection.If the control is released before the moon
roof reaches fully closed or the ignition is turned off (without accessory
delay being active), the moon roof will stop.
To vent:
•The moon roof is equipped with an automatic, one-touch, vent feature.
To tilt the moon roof into the vent position (when the glass panel is
closed), press and release the front portion of the control.
•To close the moon roof from the vent position, press and hold the rear
portion of the control until the glass panel stops moving.
The moon roof has a sliding shade that can be opened or closed when
the glass panel is shut. To close the shade, pull it toward the front of the
vehicle.
Accessory delay:
With accessory delay, the window switches, audio system, and moon roof
(if equipped) may be used for up to 10 minutes after the ignition switch
is turned off or until either front door is opened.
UNIVERSAL GARAGE DOOR OPENER (IF EQUIPPED)
Your vehicle may be equipped with a universal garage door opener which
can be used to replace the common hand-held transmitter.
Car2UHome Automation System (if equipped)
The Car2U
Home Automation
System is a universal transmitter
located in the driver’s visor that
includes two primary features – a
garage door opener and a platform
for remote activation of devices
within the home. The Car2U

system’s garage door opener
function replaces the common
hand-held garage door opener with a three-button transmitter that is
integrated into the interior of your vehicle. After being programmed for
garage doors, the Car2U
system transmitter can be programmed to
operate security devices and home lighting systems.
WARNING:Make sure that people and objects are clear of the
garage door or security device you are programming. Do not
program the Car2U
system with the vehicle in the garage.
Driver Controls
80
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

Do not use the Car2U
system with any garage door opener that lacks
safety stop and reverse features as required by U.S. Federal Safety
Standards (this includes any garage door opener manufactured before
April 1, 1982).
Be sure to keep the original remote control transmitter for use in other
vehicles as well as for future Car2U
system programming. It is also
recommended that upon the sale or lease termination of the vehicle, the
programmed Car2U
system buttons should be erased for security
reasons. Refer toErasing the Car2U
Home Automation System
buttonslater in this section.
Read the instructions completely before attempting to program the
Car2U
system. Because of the steps involved, it may be helpful to have
another person assist you in programming the transmitter.
Additional Car2U
system information can be found on-line at
www.learcar2U.com or by calling the toll-free Car2U
system help line at
1-866-572-2728.
Types of garage door openers (rolling code and fixed code)
The Car2U
Home Automation System may be programmed to operate
rolling code and fixed code garage door openers.
•Rolling code garage door openers were produced after 1996 and are
code protected. Rolling code means the coded signal is changed every
time your remote control garage door opener is used.
•Fixed code garage door openers were produced prior to 1996. Fixed
code uses the same coded signal every time. It is manually
programmed by setting DIP switches for a unique personal code.
If you do not know if your garage
door opener is a rolling code or
fixed code device, open your garage
door opener’s remote control battery
cover. If a panel of DIP switches is
present your garage door opener is
a fixed code device. If not, your
garage door opener is a rolling code
device.
12
34
5
6789
1
01
1
1
2
C
T
S
206-12 T
124
O
N
Driver Controls
81
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

Rolling code programming
Note:Programming the rolling code garage door opener involves
time-sensitive actions. Read the entire procedure prior to beginning so
you will know which actions are time-sensitive. If you do not follow the
time-sensitive actions, the device will time out and you will have to
repeat the procedure.
Note:Do not program the Car2U
system with the vehicle in the garage.
Make sure that your key is on and engine off while programming the
transmitter.
1. Firmly press the two outer
Car2U
system buttons for
1–2 seconds, then release.
2. Go to the garage to locate the
garage door opener motor and its
“learn” button. You may need a
ladder to reach the unit and you
may need to remove the unit’s cover
or light lens to locate the “learn”
button. Press the “learn” button,
after which you will have
10–30 seconds to return to your
vehicle and complete the following
steps. If you cannot locate the
“learn” button, refer to the Owner’s Guide of your garage door opener or
call the toll-free Car2U
system help line at 1-866-57Car2U
(1-866-572-2728).
Driver Controls
82
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

3. Return to your vehicle. Press and
hold the Car2U
system button you
would like to use to control the
garage door. You may need to hold
the button from 5–20 seconds,
during which time the selected
button indicator light will blink
slowly. Immediately (within
1 second) release the button once the garage door moves. When the
button is released, the indicator light will begin to blink rapidly until
programming is complete.
4. Press and release the button again. The garage door should move,
confirming that programming is successful. If your garage door does not
operate, repeat the previous steps in this section.
After successful programming, you will be able to operate your Car2U

system by pressing the button you programmed to activate the opener.
The indicator light above the selected button will turn on to confirm that
the Car2U
system is responding to the button command.
To program another rolling code device such as an additional garage door
opener, a security device or home lighting, repeat Steps 1 through 4
substituting a different function button in Step 3 than what you used for
the garage door opener. For example, you could assign the left-most
button to the garage door, the center button to a security device, and
the right-most button to another garage door opener.
Note:The Car2U
system allows for three devices to be programmed. If
you need to change or replace any of the three devices after it has been
initially programmed, it is necessary to erase the current settings using
theErasing the Car2U
Home Automation System buttonsprocedure
and then programming all of the devices being used.
Fixed code programming
Note:Do not program the Car2U
system with the vehicle in the garage.
Make sure that your key is on and engine off while programming the
transmitter.
Driver Controls
83
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

5. Press and hold the Car2U

system button you would like to use
to control the garage door.
Immediately (within 1 second)
release the button once the garage
door moves. During this time the
selected button indicator light will
blink slowly. Do not release the
button until you see the garage door move. Most garage doors open
quickly. You may need to hold the button from 5–55 seconds before
observing movement of the garage door.
6. The indicator light will (begin to) blink rapidly until programming is
complete. If your garage door opener does not operate following these
steps, repeat Steps 2 through 6. Otherwise, call the toll-free Car2U
help
line at 1-866-57Car2U (1-866-572-2728).
After successful programming, you will be able to operate your Car2U

system by pressing the button you programmed to activate the opener.
The indicator light above the selected button will turn on to confirm that
the Car2U
system is responding to the button command.
Erasing the Car2UHome Automation System buttons
Note:The system allows for three devices to be programmed. If you
need to change or replace any of the three devices after it has been
initially programmed, it will be necessary to erase the current settings
using the procedure below and then reprogramming all of the devices
being used.
To erase programming on the Car2U
system (individual buttons cannot
be erased), use the following procedure:
1. Firmly press the two outside
Car2U
system buttons
simultaneously for approximately
20 seconds until the indicator lights
begin to blink rapidly. The indicator
lights are located directly above the
buttons.
2. Once the indicator lights begin to
blink, release your fingers from the
buttons. The codes for all buttons
are erased.
If you sell your vehicle equipped with the Car2U
system, it is
recommended that you erase the programming for security reasons.
Driver Controls
85
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

service points ..................288–289
starting after a collision .........246
Engine block heater .................211
Engine oil ..................................292
checking and adding ..............292
dipstick ....................................292
filter, specifications ........295, 322
recommendations ...................295
refill capacities ........................323
specifications ..........................323
Event data recording ....................7
Exhaust fumes ..........................211
F
Fail safe cooling ........................302
Fleet MyKey programming ........92
Flexible Fuel Vehicle (FFV) ....304
Fluid capacities .........................323
Fog lamps ....................................53
Four-Wheel Drive vehicles
driving off road .......................237
preparing to drive your
vehicle .....................................222
Fuel ............................................304
calculating fuel
economy ............................20, 311
cap ...........................................307
capacity ...................................323
choosing the right fuel ...........308
comparisons with EPA fuel
economy estimates .................314
detergent in fuel .....................309
filler funnel .............................310
filling your vehicle with
fuel ...........................304, 307, 311
filter, specifications ........303, 322
fuel pump shut-off switch .....246
improving fuel economy ........311octane rating ...................308, 326
quality ......................................309
running out of fuel .........264, 310
safety information relating to
automotive fuels .....................304
Fuel - flex fuel vehicle
(FFV) .................................304, 308
Fuses ..................................246–247
G
Garage door opener ....................80
Gas cap (see Fuel cap) ............307
Gas mileage (see Fuel
economy) ...................................311
Gauges .........................................16
H
Hazard flashers .........................245
Headlamps ...................................52
aiming ........................................55
bulb specifications ....................59
daytime running lights .............54
flash to pass ..............................54
high beam .................................53
replacing bulbs .........................60
turning on and off ....................52
Heating
heating and air conditioning
system .......................................48
manual heating and air
conditioning system .................45
Hood ..........................................288
I
Ignition ...............................207, 326
Illuminated visor mirror .............66
Index
336
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)

utility-type vehicles ....................6
Specification chart,
lubricants ...................................323
Speed control ..............................74
Starting a flex fuel vehicle .......210
Starting your
vehicle ........................207–208, 210
jump starting ..........................265
Steering wheel
controls ......................................77
tilting .........................................65
Stereo
CD-MP3 .....................................27
SYNC
..........................................44
T
Tilt steering wheel ......................65
Tire Pressure Monitoring
System (TPMS)
Tires, Wheels and Loading ....189
Tires ...................................173–175
alignment ................................182
care ..........................................178
changing ..........................256, 258
checking the pressure ............178
inflating ...................................176
label .........................................188
replacing ..................................179
rotating ....................................182
safety practices .......................181
sidewall information ...............183
snow tires and chains ............193
spare tire .........................254, 256
terminology .............................175
tire grades ...............................174
treadwear ........................174, 178
Towing .......................................200recreational towing .................205
trailer towing ..........................200
wrecker ....................................270
Transmission .............................224
brake-shift interlock (BSI) ....222
fluid, checking and adding
(automatic) .............................317
fluid, refill capacities ..............323
lubricant specifications ..........323
Trunk ...........................................88
Turn signal ..................................56
U
Universal garage door opener ....80
USB port ......................................37
V
Vehicle Identification Number
(VIN) ..........................................327
Vehicle loading ..........................194
Ventilating your vehicle ...........211
W
Warning lights (see Lights) .......12
Washer fluid ..............................290
Water, Driving through .............243
Windows
power .........................................71
rear wiper/washer .....................65
Windshield washer fluid and
wipers ..........................................64
checking and adding fluid .....290
liftgate reservoir .....................290
replacing wiper blades ...291–292
Wrecker towing .........................270
Index
339
2010 Mariner(mrn)
Owners Guide, 2nd Printing
USA(fus)