torque Mercury Mariner 2010 Scheduled Maintenance Guide

It is recommended that the following basic maintenance checks and inspections be performed at the
designated time intervals. See your “Owner’s Guide” for more information.
Check every month for all vehicles
❑Check function of all interior and exterior lights.❑Check tires for wear and proper air pressure, including spare.
❑Check engine oil fluid level.
❑Check windshield washer fluid level.
Check every six months for all vehicles
❑Check lap/shoulder belts and seat latches for wear and proper operation.❑Check that externally mounted spare tire is properly stowed (tight) (see yourOwner’s Guide).
❑Check power steering fluid level, if equipped.
❑Check washer spray, wiper operation, and clean all wiper blades (replace blades as necessary).
❑Check parking brake for proper operation.
❑Check and lubricate all hinges, latches, door check straps (see dealer) and outside locks.
❑Check and lubricate upper and lower sliding door tracks, if equipped.
❑Check and clean sliding door contact switches, if equipped.
❑Check and lubricate door rubber weatherstrips.
❑Check and clean body and door drain holes.
❑Check safety warning lamps (brake, ABS, air bag, safety belt) for operation.
❑Check engine cooling system level and strength.
❑Check battery connections and clean if necessary.
❑Check clutch fluid level, if equipped.
Retightening lug nuts
❑On vehicles equipped with dual rear wheels, retighten the wheel lug nuts to the specified torque at 100 miles
(160 km), and again at 500 miles (800 km) of new vehicle operation and after any wheel disturbance
(tire rotation, changing a flat tire, wheel removal, etc.).
❑Refer toWheel Lug Nut Torque Specificationin yourOwner’s Guidefor the proper lug nut torque specification.
OWNERCHECKS ANDSERVICES
8Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

7,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
15,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
14Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

30,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission fluid level on
vehicles if equipped with dipstick. Consult
your dealer for particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
37,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
16Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

Batteries
The technicians at your Ford and Lincoln Mercury dealership can determine the health of your vehicle’s
battery during any service visit. The Motorcraft Tested Tough Max Series with its “long-life” design outlasted
other long-life batteries by up to 200%. That’s one reason why we stand behind this battery with a
national 3 year, free-replacement and prorated-cost thereafter up to 100 months with unlimited mileage.
Should your battery need to be replaced, consider any one of the batteries that bear the Motorcraft name.
45,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
18Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

52,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
60,000 miles
❑Change engine oil and replace oil filter❑Change automatic transmission fluid and filter on
all vehicles equipped with the TorqShift
transmission. Consult your dealer for your particular
requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance19
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

75,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
82,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance21
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

90,000 miles
❑Change engine oil and replace oil filter❑Inspect automatic transmission fluid level on
vehicles if equipped with dipstick. Consult
your dealer for your particular requirements.
❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filter (if equipped)❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Replace spark plugs❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
97,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
22Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

105,000 miles
❑Change engine oil and replace oil filter❑Change manual transmission fluid (except Escape)❑Replace cabin air filter (if equipped)❑Change rear axle fluid only on vehicles equipped
with DANA axles (see Special Operating
Conditions on page 41 and Exceptions on page
47)
❑Change Motorcraft Premium Gold Engine Coolant
(see Exceptions on page 47 and Premium Gold
Coolant Change Record on page 48)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
112,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance23
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs

120,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Replace climate-controlled seat filters (if
equipped)
❑Replace engine air filter❑Replace fuel filter (except Escape, Mariner,
F-Series [non Super Duty],
Expedition/Navigator [short wheel base only],
E-Series)
❑Change automatic transmission fluid and filter on
all vehicles equipped with the TorqShift
transmission. Consult your dealer for your particular
requirements.
❑Replace wheel bearing grease and grease seals
on 4x2 front wheel bearings (if non-sealed
bearings)
❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect accessory drive belts❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
24Scheduled Maintenance
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)

127,500 miles
❑Change engine oil and replace oil filter❑Inspect cabin air filter (if equipped)❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
135,000 miles
❑Change engine oil and replace oil filter❑Replace cabin air filter (if equipped)❑Inspect steering linkage, ball joints, suspension,
tie rod ends, driveshaft, and U-joints (lubricate if
equipped with Zerk fittings)
❑Torque the rear U-bolts (Transit Connect only)❑Inspect engine cooling system and hoses❑Inspect brake pads, shoes, rotors, drums, brake
lines and hoses and parking brake system.
❑Inspect half shaft boots (if equipped)❑Inspect exhaust system and heat shields❑Inspect automatic transmission fluid level (if
equipped with an underhood dipstick)
❑Inspect and lubricate 4x4 front axle U-joints❑Rotate tires, inspect tires for wear and measure
tread depth
❑Inspect the wheels and related components for
abnormal noise, wear, looseness, or drag
❑Perform multi-point inspection (recommended)
DEALERVALIDATION:
RO#: P&A C
ODE:
D
ATE:MILEAGE:
NORMALSCHEDULETRUCKS,FULLSIZEVANS& SUVS
Scheduled Maintenance25
2010 Scheduled Maintenance Guide(smg)
Scheduled Maintenance Guide, 1st Printing
USA(fus)
Normal Schedule
Trucks, Fullsize
Vans & SUVs