air condition Mercury Mercury Cougar 1996 Owner's Manuals
[x] Cancel search | Manufacturer: MERCURY, Model Year: 1996, Model line: Mercury Cougar, Model: Mercury Mercury Cougar 1996Pages: 323, PDF Size: 2.96 MB
Page 24 of 323
24 [SR21130( ALL)10/94]
half page art:0011064-AInflated right front passenger side air bag
*
[SR22200( ALL)05/95]
RWARNING
If the air bag is inflated, THE AIR BAG
WILL NOT FUNCTION AGAIN AND
MUST BE REPLACED IMMEDIATELY. If
the air bag is not replaced, the unrepaired
area will increase the risk of injury in a
collision.
*
[SR22210( ALL)05/95]
The air bag system uses a readiness light and a
tone to indicate the condition of the system. The
readiness light is in the instrument cluster. When
you turn the ignition to the ON position, this
light will illuminate for approximately six (6)
seconds and then turn off. This indicates that the
system is operating normally.NOTE:
Maintenance of the air bag system is not
required.
File:rcsrc.ex
Update:Mon Jun 12 16:51:53 1995
Page 52 of 323
52
*
[ST13500( ALL)01/95]
Have the exhaust and body ventilation systems
checked whenever:
*
[ST13600( ALL)02/95]
q
your vehicle is raised for service
*
[ST13700( ALL)02/95]
q
the sound of the exhaust system changes
*
[ST13800( ALL)01/95]
q
your vehicle has been damaged in a collision
*
[ST13900( ALL)01/95]
Improve your ventilation by keeping all air inlet
vents clear of snow, leaves, and other debris.
[ST14000( ALL)12/94]
If the engine is idling while you are stopped in
an open area for long periods of time, open the
windows at least one inch (2.5 cm). Also, the
heating or air conditioning system should be set
to any function except MAX A/C or AUTO.
[ST14125( BCGV)05/94]
q
If you use the heater, set the fan speed on
MEDIUM or HIGH with the function control
on any position except OFF and the
temperature control at any desired position.
[ST14250( BCGV)12/88]
q
If you use the air conditioner, set the fan
speed on MEDIUM or HIGH with the
function control on any position except OFF
or MAX and the temperature control at any
desired position.
File:rcstc.ex
Update:Mon Jun 12 16:50:31 1995
Page 60 of 323
60 %
*
[LG04610( ALL)01/95]
Air Bag Readiness Light
[LG04620( ALL)05/94]
The air bag system uses a readiness light to
indicate the condition of the system. If the
system is functioning properly, the light will
stay on for 6 seconds when the ignition switch is
turned to the ON position.
[LG04630( ALL)05/94]
If there is a problem with the system, two things
may happen: the readiness light will either flash
or stay lit up, or you will hear a beeping sound.
If either of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately.
[LG04645( BC )05/95]
one inch art:0011355-A%*
[LG04700( ALL)01/95]
Charging System Light
*
[LG04800( ALL)03/95]
This light indicates that your battery is not being
charged and that you need to have the electrical
system checked.
[LG04900( ALL)05/92]
one inch art:0010119-A*
[LG05100( ALL)02/95]
This light comes on every time you turn the
ignition to the ON or START position (engine
off). The light should go off when the engine
starts and the alternator begins to charge.
File:rclgc.ex
Update:Mon Jun 12 16:50:19 1995
Page 74 of 323
74 [IP00400( ALL)05/95]The main controls for the climate control system,
clock, and radio are on the instrument panel.
%*
[IP00500( ALL)05/95]
NOTE: Any cleaner or polish that increases the
gloss (shine) of the upper part of the
instrument panel should be avoided.
The dull finish in this area is to help
protect the driver from undesirable
windshield reflection.
%
*
[IP00600( ALL)01/95]
The Climate Control Systems
[IP00700( ALL)03/91]
Your vehicle has one of two different climate
control systems. The two systems are:
[IP01200( BCGV)06/93]
q
a manual heating and air conditioning system
[IP01250( BC )03/95]
q
a semi-automatic temperature control
system (if equipped)
*
[IP01400( ALL)09/89]
If you are not sure which system your vehicle
has, see the diagrams on the following pages.
% [IP10700( BCGV)08/93]
The Manual Heating and Air Conditioning
System
[IP10800( BCGV)08/93]
You can heat the inside of your vehicle, defrost
the windshield, and turn on the air conditioning
with the three knobs in the center of the
instrument panel:
[IP10900( BCGV)08/93]
q
FAN
[IP11000( BCGV)08/93]
q
TEMP
[IP11100( BCGV)08/93]
q
SELECT
File:rcipc.ex
Update:Mon Jun 12 16:49:31 1995
Page 75 of 323
75 [IP11300( BC )05/95]
one third page art:0011216-B
The knobs that control the manual heating and air
conditioning system
[IP11501( BC )05/95]
To heat the interior of your vehicle, turn the
SELECT knob to FLOOR, turn the TEMP knob
to the end of the red range (full right) and turn
the FAN knob to HI. Temperature and fan speed
can be adjusted as desired.
% [IP11700( BC )05/95]
To defrost the windshield and side windows,
turn the SELECT knob to defrostV, turn the
TEMP knob to the end of the red range
(full right) and turn the FAN knob to HI.
Temperature and fan speed can be adjusted as
desired.
[IP11901( BC )05/95]
To heat the interior and defrost the windshield
and side windows, at the same time, turn the
SELECT knob to FLOOR & DEF, turn the TEMP
knob to the end of the red range (full right) and
turn the FAN knob to HI.
[IP12100( BC )03/94]
To direct either heated or cooled air to the panel
registers and the floor at the same time, turn the
SELECT knob to PANEL & FLOOR, turn the
TEMP knob for the temperature desired and set
the fan speed as desired.
File:rcipc.ex
Update:Mon Jun 12 16:49:31 1995
Page 76 of 323
76 [IP12300( BC )05/95]To cool your vehicle using outside air, turn the
SELECT knob to A/C, turn the TEMP knob all
the way to the end of the blue range (full left)
and turn the FAN knob to the desired speed
between LO and HI. A/C provides quieter
system operation than MAX A/C, but it is not
as efficient as MAX A/C which uses recirculated
air.
% [IP12500( BC )05/95]
To ventilate your car with outside air, during
mild weather, turn the SELECT knob to PANEL,
turn the TEMP knob for the temperature desired
and set the FAN knob to the speed desired.
[IP12700( BC )08/93]
Under normal conditions, the SELECT knob
should be left in any position other than MAX
A/C or OFF when the vehicle is parked. This
allows the vehicle to ªbreatheº through the
outside air inlet duct.
[IP12900( BC )05/95]
To cool your vehicle quickly in warm weather,
turn the SELECT knob to MAX A/C, turn the
TEMP knob all the way to the end of the blue
range (full left) and turn the FAN knob to HI.
MAX A/C uses recirculated air and is the most
fuel efficient way to cool your vehicle and can
also be used in heavy traffic to prevent exhaust
fumes from entering the vehicle. MAX A/C can
also be used in high humidity areas for more
efficient operation.
[IP13100( BC )08/93]
If the interior of your vehicle is very warm,
drive for the first few minutes with the windows
open. This forces most of the hot, stale air out of
the vehicle and allows the air conditioning to
work faster.
File:rcipc.ex
Update:Mon Jun 12 16:49:31 1995
Page 80 of 323
80 [IP15300( BC )05/95]To cool your car quickly in warm weather, turn
the SELECT knob to MAX A/C and turn the
FAN knob to AUTO. As the vehicle interior
cools down, the discharge air temperature and
fan speed will automatically and gradually be
changed to maintain the set temperature with
airflow from the instrument panel registers.
[IP15400( BC )07/93]
If the interior of your vehicle is very warm,
drive for the first few minutes with the windows
open. This will force the hot, stale air out and
allow the air conditioning to work faster.
% [IP15500( BC )05/95]
To cool your vehicle with outside air, turn the
SELECT knob to A/C and turn the FAN knob to
AUTO or to a fixed speed setting as you desire.
Cooling your vehicle in this manner provides a
quieter system operation, but it will not cool as
efficiently and is not as fuel efficient as MAX
A/C which uses recirculated air.
[IP15600( BC )05/95]
To ventilate your vehicle with outside air, turn
the SELECT knob to PANEL and the FAN knob
to AUTO. The fan will remain off until the
engine is warm enough to provide heat.
However, if the interior temperature is above the
set temperature, the fan will turn on
immediately. Temperature may be set as desired
and FAN speed can be selected.
[IP15700( BC )07/93]
A/C compressor override
[IP15800( BC )03/94]
The A/C compressor can be disengaged for
more economical driving. This can be done by
turning the SELECT knob to PANEL. The A/C
compressor is automatically engaged by the
control in MAX A/C, NORM A/C, FLOOR &
DEF, and DEFROST positions if the outside
temperature is above45ÊF (7ÊC).
File:rcipc.ex
Update:Mon Jun 12 16:49:31 1995
Page 226 of 323
229
*
[SV01850(MBC )05/95]
RWARNING
The cooling fan is automatic and may
come on at any time. Always disconnect
the negative terminal of the battery before
working near the fan.
*
[SV01900( ALL)03/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000( ALL)01/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100( ALL)01/95]
q
Never get under a vehicle while it is
supported by a jack only. If you must work
under a vehicle, use safety stands.
*
[SV02200( ALL)01/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02600(MBC )03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02800( ALL)03/95]
Working with the engine off:
*
[SV03000( BCGV)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in
P (Park).
*
[SV03100( ALL)03/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV03150( ALL)03/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:rcsvc.ex
Update:Mon Jun 12 16:45:15 1995
Page 233 of 323
236 [SV08750( ALL)05/95]Octane recommendations
[SV08800( ALL)05/95]
Your engine is designed to use fuel with an
octane rating of 87. In most cases it is not
necessary to use a fuel with an octane rating
higher than 87. At service stations, the octane
rating is displayed in a label on the pumps.
[SV08900( ALL)05/95]
one inch art:0060001-C[SV09100( ALL)05/95]
Using a fuel with a lower octane rating can
cause persistent and heavy knocking, which can
damage the engine.
[SV09200( ALL)05/95]
Do not be concerned if your vehicle sometimes
knocks lightly when you drive up a hill or when
you accelerate. However, see your dealer or a
qualified service technician if persistent heavy
knocking occurs because this can damage the
engine.
[SV09350( ALL)05/95]
If your vehicle has problems with starting, rough
idle or hesitation problems when the engine is
cold, it may be caused by fuel with low
volatility. Try a different brand of fuel. If the
condition persists, see your dealer or a qualified
service technician.
[SV09800( ALL)05/95]
Gasolines for clean air
[SV09900( ALL)05/95]
Fuels in certain areas of the country are required
to contain oxygenates to improve air quality.
Common oxygenates are ethanol or grain alcohol
(blended at no more than 10%), methanol or
wood alcohol (blended at no more than 5% with
cosolvents and additives), and MTBE or methyl
tertiary butyl ether (blended at no more than
15%).
File:rcsvc.ex
Update:Mon Jun 12 16:45:15 1995
Page 284 of 323
287
*
[SV53400( ALL)01/95]
By law, anyone who manufactures, repairs,
services, sells, leases, trades vehicles, or
supervises a fleet of vehicles is not permitted to
intentionally remove an emission control device
or prevent it from working. In some of the
United States and in Canada, vehicle owners
may be liable if their emission control device is
removed or is prevented from working.
*
[SV53500( ALL)02/92]
Never use a metal exhaust collector when you
service your vehicle. If the metal collector
contacts any of your vehicle's plastic trim or
bumper parts they could melt or deform.
*
[SV53600( ALL)01/95]
Do not drive your vehicle if it does not operate
properly. See your dealer if the engine runs on
for more than five seconds after you shut it off
or if it misfires, surges, stalls, or backfires.
%*
[SV53700( ALL)02/95]
Information about your vehicle's emission
control system is on the Vehicle Emission
Control Information decal located on or near the
engine. This decal identifies engine displacement
and gives some tune-up specifications.
%*
[SV53702( ALL)05/95]
Readiness for Inspection/Maintenance
Testing
*
[SV53715( ALL)05/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies a
ªneed for additional mixed city and highway
driving to complete the checkº of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
File:rcsvc.ex
Update:Mon Jun 12 16:45:15 1995