brakes Mercury Milan 2006 Owner's Manuals
[x] Cancel search | Manufacturer: MERCURY, Model Year: 2006, Model line: Milan, Model: Mercury Milan 2006Pages: 256, PDF Size: 2.45 MB
Page 2 of 256
Seating and Safety Restraints 89
Seating 89
Safety restraints 94
Airbags 108
Child restraints 123
Tires, Wheels and Loading 135
Tire information 135
Vehicle loading 149
Trailer towing 154
Recreational towing 154
Driving 156
Starting 156
Brakes 160
Traction Control™ 161
Transmission operation 163
Roadside Emergencies 170
Getting roadside assistance 170
Hazard flasher switch 172
Fuel pump shut-off switch 172
Fuses and relays 173
Changing tires 179
Lug nut torque 184
Jump starting 185
Wrecker towing 190
Customer Assistance 191
Reporting safety defects (U.S. only) 197
Cleaning 198
Table of Contents
2
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Page 56 of 256
3. Press the SET + control and
release it.
4. Take your foot off the accelerator
pedal.
5. The indicator
light on the
instrument cluster will turn on.
Note:
•Vehicle speed may vary momentarily when driving up and down a
steep hill.
•If the vehicle speed increases above the set speed on a downhill, you
may want to apply the brakes to reduce the speed.
•If the vehicle speed decreases more than 10 mph (16 km/h) below
your set speed on an uphill, your speed control will disengage.
Disengaging speed control
To disengage the speed control:
•Depress the brake pedal or clutch pedal (if equipped)
Disengaging the speed control will not erase previous set speed.
Resuming a set speed
Press the RESUME control and
release it. This will automatically
return the vehicle to the previously
set speed. The RESUME control will
not work if the vehicle speed is not
faster than 30 mph (48 km/h).
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
56
Page 100 of 256
All safety restraints in the vehicle are combination lap and shoulder
belts. All of the passenger combination lap and shoulder belts have two
types of locking modes described below:
Vehicle sensitive mode
This is the normal retractor mode, which allows free shoulder belt length
adjustment to your movements and locking in response to vehicle
movement. For example, if the driver brakes suddenly or turns a corner
sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h)
or more, the combination safety belts will lock to help reduce forward
movement of the driver and passengers.
Automatic locking mode
How to use the automatic locking mode
•Buckle the combination lap and
shoulder belt.
•Grasp the shoulder portion and
pull downward until the entire
belt is pulled out.
•Allow the belt to retract. As the belt retracts, you will hear a clicking
sound. This indicates the safety belt is now in the automatic locking
mode.
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Seating and Safety Restraints
100
Page 160 of 256
BRAKES
Occasional brake noise is normal. If a metal-to-metal, continuous grinding
or continuous squeal sound is present, the brake linings may be worn-out
and should be inspected by an authorized dealer. If the vehicle has
continuous vibration or shudder in the steering wheel while braking, the
vehicle should be inspected by an authorized dealer.
Refer toBrake system warning
lightin theInstrument Cluster
chapter for information on the brake
system warning light.
Four-wheel anti-lock brake system (ABS) (if equipped)
Your vehicle may be equipped with an Anti-lock Braking System (ABS).
This system helps you maintain steering control during emergency stops
by keeping the brakes from locking. The ABS operates by detecting the
onset of wheel lockup during brake application and compensates for this
tendency. Noise from the ABS pump motor and brake pedal pulsation
may be observed during ABS braking; any pulsation or mechanical noise
you may feel or hear is normal. In addition, the ABS performs a
self-check after you start the engine and begin to drive away. A brief
mechanical noise may be heard during this test. This is normal.
ABS warning lamp
The ABS lamp in the instrument
cluster momentarily illuminates
when the ignition is turned on. If
the light does not illuminate during
start up, remains on or flashes, the
ABS may be disabled and may need to be serviced.
Even when the ABS is disabled and
the ABS light is on, normal braking
is still effective. (If your BRAKE
warning lamp illuminates with the
parking brake released, have your
brake system serviced immediately.)
P!
BRAKE
ABS
P!
BRAKE
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driving
160
Page 161 of 256
Using ABS
When hard braking is required, apply continuous force on the brake
pedal; do not pump the brake pedal since this will reduce the
effectiveness of the ABS and will increase your vehicle’s stopping
distance. The ABS will be activated immediately, allowing you to retain
full steering control during hard braking and on slippery surfaces.
However, the ABS does not decrease stopping distance and does not
decrease the time necessary to apply the brakes.
Parking brake
To set the parking brake (1), pull
the parking brake handle up as far
as possible.
The BRAKE warning lamp will
illuminate and will remain
illuminated until the parking brake
is released.
To release, press and hold the button (2), pull the handle up slightly,
then push the handle down.
Always set the parking brake fully and make sure that the
gearshift is securely latched in P (Park) (automatic
transmission) or in 1 (First) (manual transmission).
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer as soon as possible.
TRACTION CONTROL(IF EQUIPPED)
The Traction Controlsystem helps you maintain the stability and
steerability of your vehicle, especially on slippery road surfaces such as
snow- or ice-covered roads and gravel roads. The system will allow your
vehicle to make better use of available traction in these conditions.
12
P!
BRAKE
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driving
161
Page 164 of 256
If you cannot move the gearshift lever out of P (Park) with ignition in
the RUN position and the brake pedal depressed:
1. Apply the parking brake, turn
ignition key to LOCK, then remove
the key.
2. Using a screwdriver (or similar
tool), remove the protective cover
to the interlock release access hole
on the console. Insert the
screwdriver (or similar tool) to
release the interlock.
3. Start the vehicle.
If it is necessary to use the above procedure to move the gearshift lever,
it is possible that a fuse has blown or the vehicle’s brakelamps are not
operating properly. Refer toFuses and relaysin theRoadside
Emergencieschapter.
Do not drive your vehicle until you verify that the brakelamps
are working.
Always set the parking brake fully and make sure the gearshift is
latched in P (Park). Turn the ignition to the LOCK position and
remove the key whenever you leave your vehicle.
If the parking brake is fully released, but the brake warning lamp
remains illuminated, the brakes may not be working properly.
See your authorized dealer as soon as possible.
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driving
164
Page 169 of 256
2. Hold the clutch pedal down and move the gearshift lever into the
neutral position. Wait at least three seconds before shifting into R
(Reverse).
•The gearshift lever can only be moved into R (Reverse) by moving it
from left of 3 (Third) and 4 (Fourth) before shifting into R (Reverse).
This is a lockout feature that protects the transmission from
accidentally being shifted into R (Reverse) from 5 (Fifth).
Parking your vehicle
1. Apply the brake and shift into the neutral position.
2. Fully apply the parking brake, then shift into 1 (First).
3. Turn the ignition off.
Do not park your vehicle in Neutral, it may move unexpectedly
and injure someone. Use 1 (First) gear and set the parking brake
fully.
Removing the key
Turn the ignition to position 1 (LOCK) and remove the key.
DRIVING THROUGH WATER
If driving through deep or standing
water is unavoidable, proceed very
slowly especially when the depth is
not known. Never drive through
water that is higher than the bottom
of the wheel rims (for cars) or the
bottom of the hubs (for trucks).
When driving through water, traction or brake capability may be limited.
Also, water may enter your engine’s air intake and severely damage your
engine or your vehicle may stall.Driving through deep water where
the transmission vent tube is submerged may allow water into the
transmission and cause internal transmission damage.
Once through the water, always dry the brakes by moving your
vehicle slowly while applying light pressure on the brake pedal.
Wet brakes do not stop the vehicle as quickly as dry brakes.
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driving
169
Page 234 of 256
BRAKE/CLUTCH FLUID
Brake and clutch systems are supplied from the same reservoir.
The fluid level will drop slowly as
the brakes wear, and will rise when
the brake components are replaced.
Fluid levels between the “MIN” and
“MAX” lines are within the normal
operating range; there is no need to
add fluid. If the fluid levels are
outside of the normal operating
range the performance of the
system could be compromised; seek
service from your authorized dealer
immediately.
TRANSAXLE FLUID
Checking 5–speed automatic transaxle fluid (If equipped)
Refer to yourscheduled maintenance informationfor scheduled
intervals for fluid checks and changes. Your transaxle does not consume
fluid. However, the fluid level should be checked if the transaxle is not
working properly, i.e., if the transaxle slips or shifts slowly or if you
notice some sign of fluid leakage.
Automatic transmission fluid expands when warmed. To obtain an
accurate fluid check, drive the vehicle until it is warmed up
(approximately 20 miles [30 km]). If your vehicle has been
operated for an extended period at high speeds, in city traffic
during hot weather or pulling a trailer, the vehicle should be
turned off for about 30 minutes to allow fluid to cool before
checking.
1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating
temperature.
2. Park the vehicle on a level surface and engage the parking brake.
3. With the parking brake engaged and your foot on the brake pedal,
start the engine and move the gearshift lever through all of the gear
ranges. Allow sufficient time for each gear to engage.
4. Latch the gearshift lever in P (Park) and leave the engine running.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If
necessary, refer toIdentifying components in the engine compartment
in this chapter for the location of the dipstick.
MAX
MIN
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Maintenance and Specifications
234
Page 251 of 256
A
Accessory delay ..........................53
Air cleaner filter ...............238–240
Air conditioning ....................28, 30
Airbag supplemental restraint
system ........................108, 117, 120
and child safety seats ............110
description ..............108, 117, 120
disposal ....................................123
driver airbag ............110, 118, 121
indicator light .........117, 119, 122
operation .................110, 118, 121
passenger airbag .....110, 118, 121
side airbag .......................117, 120
Antifreeze
(see Engine coolant) ................217
Anti-lock brake system
(see Brakes) ......................160–161
Anti-theft system ..................83, 86
arming the system ....................86
disarming a triggered system ..87
triggering ...................................88
Audio system (see Radio) ...16, 20
Automatic transaxle
fluid, adding ............................234
fluid, checking ........................234
Automatic transmission
driving an automatic
overdrive .........................165–166
fluid, adding ............................236
fluid, checking ........................236
fluid, refill capacities ..............241
fluid, specification ..................244
Axle
lubricant specifications ..243–244
B
Battery .......................................215acid, treating emergencies .....215
jumping a disabled battery ....185
maintenance-free ....................215
replacement, specifications ...240
servicing ..................................215
BeltMinder...............................103
Brakes ........................................160
anti-lock ...........................160–161
anti-lock brake system (ABS)
warning light ...........................160
fluid, checking and adding ....234
fluid, refill capacities ..............241
fluid, specifications .........243–244
lubricant specifications ..243–244
parking ....................................161
shift interlock ..........................163
Break-in period .............................5
Bulbs ............................................38
C
Capacities for refilling fluids ....241
Cassette tape player ...................16
Cell phone use ..............................7
Changing a tire .........................179
Child safety restraints ..............124
child safety belts ....................124
Child safety seats ......................127
attaching with tether straps ..131
in front seat ............................128
in rear seat ..............................128
Cleaning your vehicle
engine compartment ..............199
instrument panel ....................202
interior .....................................202
interior trim ............................202
plastic parts ............................201
washing ....................................198
waxing .....................................198
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Index
251
Page 254 of 256
L
Lamps
autolamp system .......................34
bulb replacement
specifications chart ..................39
daytime running light ...............35
fog lamps ...................................35
headlamps .................................34
headlamps, flash to pass ..........36
instrument panel, dimming .....36
interior lamps ...........................38
replacing bulbs .........................39
Lane change indicator
(see Turn signal) ........................38
Lights, warning and indicator ....10
anti-lock brakes (ABS) ..........160
Load limits .................................149
Locks
autolock .....................................81
childproof ..................................73
doors ..........................................71
Lubricant specifications ...243–244
Lug nuts ....................................184
Lumbar support, seats ...............90
M
Manual transaxle
fluid capacities ........................241
fluid, checking and adding ....238
lubricant specifications ..........244
Manual transmission .................168
reverse .....................................168
Message center ...........................61
english/metric button ...............66
system check button ................65
warning messages .....................66
Mirrors .........................................54automatic dimming rearview
mirror ........................................54
heated ........................................55
programmable memory ............77
side view mirrors (power) .......54
Moon roof ....................................59
Motorcraft parts ........203, 223, 240
O
Octane rating ............................226
Oil (see Engine oil) ..................210
P
Parking brake ............................161
Parts (see Motorcraft parts) ....240
Passenger Occupant
Classification Sensor ...................96
Power distribution box
(see Fuses) ...............................176
Power door locks ........................71
Power mirrors .............................54
Power point .................................52
Power steering ..................162–163
fluid, checking and adding ....233
fluid, refill capacity ................241
fluid, specifications .........243–244
Power Windows ...........................53
R
Radio ......................................16, 20
Relays ........................................173
Remote entry system ...........74, 76
illuminated entry ................79–80
locking/unlocking doors ...........76
opening the trunk .....................77
2006 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Index
254