bulb Mercury Milan 2007 s User Guide

5. Remove screw from oval splash
shield access panel from the
exterior wheel well area. Lift up and
rearward to release a hidden finger
attachment at the lower portion of
the panel (Passenger side only with
ABS).
6. From the exterior wheel well area
reach arm through splash shield
opening to access bulb socket
(Passenger side only with ABS).
7. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
8. Let go of the bulb socket and let
the bulb socket dangle downward
near the lamp housing (Passenger
side only with ABS).
9. Reach over the front bolster in
the engine area, with a tool if
necessary, bring the bulb socket
upwards into an unobstructed area to replace the bulb (Passenger side
only with ABS).
10. Carefully pull bulb straight out
of socket and push in the new one.
11. After the new bulb is installed,
carefully let the bulb socket dangle
downward near the lamp housing
(Passenger side only with ABS).
12. From the exterior wheel well
area reach arm through splash
shield opening to install bulb socket with new bulb (Passenger side only
with ABS).
13. Install new bulb socket into the lamp assembly by aligning the
indexing fingers, then rotate clockwise to locked position.
14. Reinstall the AirTube to the air filter assembly. (Driver’s side only).
15. Reinstall the vertical shield to the bolster. (Driver’s side only).
16. Reinstall the splash shield access panel with screw. (Passenger side
only with ABS).
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
57

Replacing front side marker bulbs
1. Make sure the headlamp control
is in the OFF position.
2. Pry the lamp away from the
vehicle at the rear of lamp at the
wheel opening. (Rotate lamp from
the wheel opening away from the
vehicle), as the lamp separates from
the vehicle, slide the lamp towards
the wheel opening to disengage
lamp.
3. Rotate the lamp clockwise while
holding the electrical connector in
place with your other hand. After
rotating the lamp 90 degrees
clockwise, pull and disengage the
wire harness and bulb from the
lamp.
4. With the bulb exposed, carefully remove the bulb from the socket by
grasping the bulb and pulling it away from the wire harness.
Replace with a new bulb, and reverse the removal steps to complete the
process.
Replacing stop/tail/turn/and side marker bulbs
Your vehicle is equipped with a rear lamp that has a stop/tail/turn/and
side marker lamp module containing integral multiple light emitting
diodes (LED). If one or more LEDs burn out, the complete lamp module
has to be replaced. See your authorized dealer for the replacement LED
module.
Replacing rear turn signal bulbs
1. Make sure the headlamp switch is in the OFF position and open the
trunk.
2. Lift out trunk floor carpeting panel to access a Luggage Scuff Plate
(Hard Molding) shingles and a Trunk Side Panel (dark grey, soft
wheelhouse side trim panel) at the lamp area.
3. Carefully pull/push the Trunk Side Panel (dark grey, soft wheelhouse
side trim panel) outboard to expose the lamp assembly. The most
effective point to grasp the Trunk Side Panel when pulling it out from
the Luggage Scuff Plate is at it’s bottom edge where that edge meets the
exposed sheet metal of the trunk floor.
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
58

Note:Do not allow the Trunk Side Panel to remain bent and untucked
from the Luggage Scuff Plate (hard molding) for a long period of time.
Doing so may result in permanent deformation.
4. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
5. Pull the bulb from the socket and
push in the new bulb.
6. Install the bulb socket into the
lamp assembly by rotating it
clockwise.
7. Carefully push the Trunk Side
Panel (dark grey, soft wheelhouse
side trim panel) back to the shingle position to the Luggage Scuff Plate
(hard molding).
8. Install trunk floor carpeting panel.
Replacing backup lamp bulbs
The backup lamp bulbs are located in the trunk lid.
1. Make sure headlamp switch is in OFF position and open trunk to
access the lamp assembly.
2. Position the decklid trim aside by removing 3 to 4 pin-type retainers
to expose the lamp assembly.
3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
4. Pull the bulb from the socket and
push in the new bulb.
5. Install the bulb socket into the
lamp assembly by rotating it
clockwise.
6. Carefully reposition the trim back
to its original position and secure
the retainers.
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
59

Replacing high-mount brake lamp bulb
1. Make sure the ignition control is
in the LOCK (OFF) position.
2. Open the trunk and reach
underneath package tray to locate
lamp assembly.
3. Remove the bulb socket by
rotating it counterclockwise, then
pulling it out of the lamp assembly.
4. Pull the bulb straight from the
socket and push in the new bulb.
5. Install the bulb socket into the lamp assembly by rotating it clockwise.
Replacing license plate lamp bulbs
1. Make sure the headlamp switch is
in the OFF position.
2. Remove the two screws from the
license plate lamp assembly.
3. Remove bulb socket by turning
counterclockwise.
4. Carefully pull the bulb out from
the socket.
Install new bulb(s) in reverse order.
Replacing foglamp bulbs (if equipped)
1. Make sure the foglamp switch is
in the OFF position.
2. From underneath the vehicle,
partially remove the tire splash
shield by removing four drive
screws.
After removing to allow free access
to the front fog lamp bulb and
electrical wire harness, the splash shield flap should be able to be
repositioned.
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
60

3. Rotate the harness/bulb assembly
counterclockwise, to remove from
the fog lamp.
4. Carefully disconnect the bulb
from the harness assembly via the
two snap clips.
Install the new bulb in reverse order.
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Lights
61

LOW BRAKE FLUID.Indicates the brake fluid level is low and the
brake system should be inspected immediately. Refer toBrake fluid
reservoirin theMaintenance and Specificationschapter.
TRUNK AJAR.Displayed when the trunk is not completely closed.
COMPASS ERROR (if equipped).Displayed when the compass is not
operating properly. If the warning stays on or continues to come on,
contact your authorized dealer as soon as possible.
CHECK LEFT OR RIGHT HEADLAMPS.Displayed when the
headlamps are activated and at least one low beam is burned out. Check
the lamps as soon as possible and have the burned out lamp replaced.
Refer toReplacing headlamp bulbsin theLightschapter.
CHECK LF OR RF TURN LAMPS.Displayed when the turn signals are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced. Refer to
Replacing headlamp bulbsin theLightschapter.
CHECK LR OR RR TURN LAMPS.Displayed when the rear turn
signals are activated and at least one is burned out. Check the lamps as
soon as safely possible and have the burned out lamp replaced. Refer to
Replacing headlamp bulbsin theLightschapter.
INTEGRATED KEY PROGRAMMING STATUS.Displayed when an
attempt is made to program a fifth Integrated Key to the Remote Key
Entry System. For more information on Integrated Key, refer toLocks
and Securitychapter in this manual.
INTERIOR TRUNK CONTROL
Press the remote trunk release
control on the instrument panel to
the left of the steering wheel.
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Driver Controls
81

the next time the engine is started. A driving cycle consists of a cold
engine startup followed by mixed city/highway driving. No additional
vehicle service is required.
If the
indicator remains on, have your vehicle serviced at the first
available opportunity. Although some malfunctions detected by the
OBD-II may not have symptoms that are apparent, continued driving
with the
indicator on can result in increased emissions, lower fuel
economy, reduced engine and transmission smoothness, and lead to more
costly repairs.
Readiness for Inspection/Maintenance (I/M) testing
Some state/provincial and local governments may have
Inspection/Maintenance (I/M) programs to inspect the emission control
equipment on your vehicle. Failure to pass this inspection could prevent
you from getting a vehicle registration. Your vehicle may not pass the I/M
test if the
indicator is on or not working properly (bulb is burned
out), or if the OBD-II system has determined that some of the emission
control systems have not been properly checked. In this case, the vehicle
is considered not ready for I/M testing.
If the
indicator is on or the bulb does not work, the vehicle may
need to be serviced. Refer to the On board diagnostics (OBD-II)
description in this chapter.
If the vehicle’s engine or transmission has just been serviced, or the
battery has recently run down or been replaced, the OBD-II system may
indicate that the vehicle is not ready for I/M testing. To determine if the
vehicle is ready for I/M testing, turn the ignition key to the ON position
for 15 seconds without cranking the engine. If the
indicator blinks
eight times, it means that the vehicle is not ready for I/M testing; if
the
indicator stays on solid, it means that the vehicle is ready for
I/M testing.
The OBD-II system is designed to check the emission control system
during normal driving. A complete check may take several days. If the
vehicle is not ready for I/M testing, the following driving cycle consisting
of mixed city and highway driving may be performed:
15 minutes of steady driving on an expressway/highway followed by 20
minutes of stop-and-go driving with at least four 30 second idle periods.
Allow the vehicle to sit for at least eight hours without starting the
engine. Then, start the engine and complete the above driving cycle. The
engine must warm up to its normal operating temperature. Once started,
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Maintenance and Specifications
254

A
Accessory delay ..........................67
Air cleaner filter ...............261–263
Air conditioning ....................41, 43
Airbag supplemental restraint
system ........................120, 129, 132
and child safety seats ............122
description ..............120, 129, 132
disposal ....................................135
driver airbag ............122, 130, 133
indicator light .........128, 131, 134
operation .................122, 130, 133
passenger airbag .....122, 130, 133
side airbag ...............................129
All Wheel Drive (AWD),
driving off road .........................182
Antifreeze
(see Engine coolant) ................238
Anti-lock brake system
(see Brakes) ..............................173
Anti-theft system ..................95, 98
arming the system ....................98
disarming a triggered system ..99
triggering ...................................99
Audio system (see Radio) ...20, 25
Automatic transaxle
fluid, adding ............................256
fluid, checking ........................256
Automatic transmission
driving an automatic
overdrive .........................178–179
fluid, adding ....................258, 261
fluid, checking ................258, 261
fluid, refill capacities ..............265
fluid, specification ..................265Auxiliary Input Jack ...................32
Axle
lubricant specifications ..........265
B
Battery .......................................236
acid, treating emergencies .....236
jumping a disabled battery ....204
maintenance-free ....................236
replacement, specifications ...263
servicing ..................................236
Belt-Minder.............................115
Brakes ........................................172
anti-lock ...................................173
anti-lock brake system (ABS)
warning light ...........................173
fluid, checking and adding ....256
fluid, refill capacities ..............265
fluid, specifications .................265
lubricant specifications ..........265
parking ....................................174
shift interlock ..........................176
Break-in period .............................5
Bulbs ............................................51
C
Capacities for refilling fluids ....265
Cassette tape player ...................20
Cell phone use ..............................7
Changing a tire .........................198
Child safety restraints ..............135
child safety belts ....................135
Child safety seats ......................139
attaching with tether straps ..143
in front seat ............................140
in rear seat ..............................140
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Index
273

Engine oil ..................................231
change oil soon warning,
message center .......................231
checking and adding ..............231
dipstick ....................................231
filter, specifications ........235, 263
recommendations ...................235
refill capacities ........................265
specifications ..........................265
Exhaust fumes ..........................172
F
Fail safe cooling ........................243
Fluid capacities .........................265
Foglamps .....................................48
Four-Wheel Drive vehicles
driving off road .......................183
Fuel ............................................244
calculating fuel
economy ............................75, 249
cap ...........................................246
capacity ...................................265
choosing the right fuel ...........247
comparisons with EPA fuel
economy estimates .................252
detergent in fuel .....................248
filling your vehicle
with fuel ..................244, 246, 249
filter, specifications ........244, 263
fuel pump shut-off switch .....191
improving fuel economy ........249
octane rating ...................248, 268
quality ......................................248
running out of fuel .................248
safety information relating
to automotive fuels ................244
Fuel pump shut-off switch .......191
Fuses ..................................191–192G
Gas cap (see Fuel cap) ............246
Gas mileage
(see Fuel economy) .................249
Gauges .........................................13
H
Hazard flashers .........................190
Head restraints .........................100
Headlamps ...................................47
aiming ..................................49–50
autolamp system .......................47
bulb specifications ....................52
daytime running lights .............48
flash to pass ..............................49
high beam .................................49
replacing bulbs .........................52
turning on and off ....................47
Heating
heating and air conditioning
system ...........................39, 41, 43
Hood ..........................................227
How to get going ........................16
I
Ignition ...............................169, 268
Illuminated visor mirror .............63
Infant seats
(see Safety seats) .....................139
Inspection/maintenance (I/M)
testing ........................................254
Instrument panel ........................65
cleaning ...................................222
cluster ........................................10
lighting up panel and
interior .......................................49
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Index
275

J
Jack ............................................198
positioning ...............................198
storage .....................................198
Jump-starting your vehicle ......204
K
Keyless entry system
autolock .....................................85
Keys .......................................82, 96
positions of the ignition .........169
L
Lamps
autolamp system .......................47
bulb replacement
specifications chart ..................52
daytime running light ...............48
fog lamps ...................................48
headlamps .................................47
headlamps, flash to pass ..........49
instrument panel, dimming .....49
interior lamps ...........................51
replacing bulbs .........................52
Lane change indicator
(see Turn signal) ........................51
Lights, warning and indicator ....10
anti-lock brakes (ABS) ..........173
Load limits .................................162
Locks
autolock .....................................85
childproof ..................................88
doors ..........................................84
Lubricant specifications ...........265
Lug nuts ....................................203
Lumbar support, seats .............101M
Manual transmission .................181
fluid capacities ........................265
lubricant specifications ..........265
reverse .....................................182
Message center ...........................74
english/metric button ...............79
system check button ................78
warning messages .....................79
Mirrors .........................................68
automatic dimming rearview
mirror ........................................67
heated ........................................68
side view mirrors (power) .......68
Moon roof ....................................72
Motorcraft parts ........224, 244, 263
N
Navigation system .......................38
O
Octane rating ............................248
Oil (see Engine oil) ..................231
P
Parking brake ............................174
Parts (see Motorcraft parts) ....263
Passenger Occupant
Classification Sensor .................107
Power distribution box
(see Fuses) ...............................195
Power door locks ........................84
Power mirrors .............................68
Power point .................................65
2007 Milan(mln)
Owners Guide (post-2002-fmt)
USA(fus)
Index
276