key Mercury Mountaineer 1998 s Owner's Guide

SecuriLockykeys and the new
unprogrammed SecuriLockykey
readily accessible for the
procedure. Please read and
understand the entire procedure
before you begin.
1. Insert the first previously
programmed SecuriLockykey into
the ignition switch and turn the
ignition from OFF to RUN
(maintain ignition in RUN for at
least one second).
2. Turn ignition to OFF and
remove the first SecuriLockykey
from the ignition switch.
3. Within five seconds of turning
the ignition to OFF, insert the
second previously programmed
SecuriLockykey into the ignition
switch and turn the ignition from
OFF to RUN (maintain ignition in
RUN for at least one second but no
more than 5 seconds).
4. Turn the ignition to OFF and
remove the second SecuriLocky
key from the ignition switch.
5. Within 10 seconds of turning the
ignition to OFF, insert the
unprogrammed SecuriLockykey
(new key) into the ignition switch
and turn the ignition from OFF to
RUN (maintain ignition switch in
RUN for at least one second). This
step will program your new
SecuriLockykey.
6. If it is desired to program
additional SecuriLockykey(s),
repeat this procedure from step 1.
Controls and features
60

If the programming procedure was
successful, the new SecuriLocky
key(s) will start the vehicle's
engine. The theft indicator
(located on the instrument cluster)
will light for three seconds and
then go out.
If the programming procedure was
not successful, the new
SecuriLockykey(s) will not
operate the vehicle's engine. The
theft indicator will flash on and off.
Wait at least one minute and then
repeat the procedure from step 1.
If failure repeats, bring your
vehicle to your dealership to have
the spare SecuriLockykey(s)
programmed.
Controls and features
61

Conditions of operation
If... Then...
The driver's safety belt is not
buckled before the ignition key
is turned to ON...The safety belt warning light
illuminates for one to two minutes and
the warning chime sounds for four to
eight seconds.
The driver's safety belt is
buckled while the indicator
light is illuminated and the
warning chime is sounding...The safety belt warning light turns off.
The driver's safety belt is
buckled before the ignition key
is turned to ON...The safety belt warning light remains
off.
Safety belt maintenance
Check the safety belt systems
periodically to make sure they
work properly and are not
damaged. Check the safety belts to
make sure there are no nicks,
wears or cuts. All safety belt
assemblies, including retractors,
buckles, front seat belt buckle
assemblies (slide bar)(if
equipped), shoulder belt height
adjusters (if equipped), child
safety seat tether bracket
assemblies (if equipped), and
attaching hardware, should be
inspected after a collision. Ford
recommends that all safety belt
assemblies used in vehicles
involved in a collision be replaced.
However, if the collision was minor
and a qualified technician finds
that the belts do not show damage
and continue to operate properly,
they do not need to be replaced.
Seating and safety restraints
72

²Make sure the parking brake is
set.
²Make sure the gearshift is in P
(Park).
3. Turn the key to 4 (ON) without
turning the key to 5 (START).
3
2
1
5
4
C
012345
6
RPMx1000ABS
CHECK
ENGINE
DOOR
AJAR
EFH
H
H
PRN D 2 1THEFT
SPEED
CONT
4WD
4WD
LOW
O/D
OFFL
L
10MPH 205060
70
304080
90
km/h
0 0 0
10 100
1
20
1
0 0 0 0 0 0406080100
120
140
160
180
20
DOOR
AJAR
CHECK
GAGE
!BRAKE
Starting
96

Make sure the corresponding lights
illuminate briefly. If a light fails to
illuminate, have the vehicle
serviced.
²If the driver's safety belt is
fastened, the light (
) will not
illuminate.
STARTING THE ENGINE
1. Turn the key to 5 (START)
without pressing the accelerator
pedal and release as soon as the
engine starts. The key will return
to 4 (ON).
2. If the engine does not start
within five seconds, wait ten
seconds and try again.
3. If the engine does not start in
two attempts OR if the
temperature is below -12ÉC (10ÉF),
depress the accelerator and start
the engine while holding the
accelerator down. Release the
accelerator when the engine starts.
4. After idling for a few seconds,
apply the brake and release the
parking brake.
Using the engine block heater
(if equipped)
An engine block heater warms the
engine coolant, which improves
starting, warms up the engine
faster and allows the
3
2
1
5
4
Starting
97

The air suspension shut-off switch
is located in the cargo area behind
the left rear quarter trim panel.
On vehicles equipped with
Air Suspension, turn OFF
the Air Suspension switch prior
to jacking, hoisting or towing
your vehicle.
Normal vehicle operation does not
require any action by the driver.
TRANSMISSION OPERATION
Automatic transmission
operation
Brake-shift interlock
This vehicle is equipped with a
brake-shift interlock feature that
prevents the gearshift from being
moved from P (Park) unless the
brake pedal is depressed.
If you cannot move the gearshift
out of P (Park) with the brake
pedal depressed:
1. Apply the parking brake, turn
ignition key to LOCK, then remove
the key.
2. Insert the key and turn it to
OFF. Apply the brake pedal and
shift to N (Neutral).
3. Start the vehicle.
If it is necessary to use the above
procedure to move the gearshift, it
is possible that a fuse has blown.
Refer toFuses and relaysin the
Roadside emergencieschapter.
Driving
104

seconds and return the key to the
OFF position.
5. Make a further check for leaks
in the fuel system.
The fuel pump shut-off switch is
located in the passenger's foot
well, behind the kick panel.
FUSES AND RELAYS
Fuses
If electrical components in the
vehicle are not working, a fuse
may have blown. Blown fuses are
identified by a broken wire within
the fuse. Check the appropriate
fuses before replacing any
electrical components.
1515
Roadside emergencies
136

²Keep all lit cigarettes, open
flames and other lit material
away from the battery and all
fuel related parts.
If you disconnect the battery, the
engine must ªrelearnº its idle
conditions before your vehicle will
drive properly, as explained in
Batteryin this chapter.
Working with the engine off
1. Set the parking brake and
ensure the gearshift is securely
latched in P (Park).
2. Turn off the engine and remove
the key.
3. Block the wheels to prevent the
vehicle from moving unexpectedly.
Working with the engine on
1. Set the parking brake and
ensure the gearshift is securely
latched in P (Park).
2. Block the wheels to prevent the
vehicle from moving unexpectedly.
Do not start your engine
with the air cleaner
removed and do not remove it
while the engine is running.
Maintenance and care
155

improving fuel economy ........134
octane rating ...........................185
quality ......................................186
safety information relating to
automotive fuels .....................183
Fuel gauge ...................................15
Fuel pump shut-off switch .......135
Fuse panels
instrument panel ....................138
power distribution box ...........141
Fuses ...................................136,137
Gauges, Mechanical ....................12
engine coolant temperature
gauge .........................................13
Hazard flashers .........................135
Head restraints ......................62,65
Headlamps ...................................16
daytime running lights .............16
flashing ......................................17
high beam .................................17
Heating ........................................18
High beams
indicator light .............................9
Hood
release lever ............................156
Instrument panel
lighting up panel and interior..17
Jump-starting your
vehicle .................................149,151
attaching cables ......................150
disconnecting cables ..............151
Keyless entry system
autolock .....................................50
keypad .......................................52
locking and unlocking doors ....54
programming entry code ....53,54
Keys
key in ignition chime ...............12
Liftgate ........................................43
Lights, warning and indicator
air bag ..........................................8
anti-lock brakes (ABS) ..............9anti-theft ...................................10
brake ............................................9
charging system ........................10
check engine ............................6,7
cruise indicator .........................11
door ajar ....................................10
fuel reset .....................................8
overdrive off ..............................11
safety belt ...................................8
turn signal indicator ...................9
Load limits
trailer towing ..........................125
Lubricant specifications ...........207
Luggage rack .............................133
Mirrors
cleaning ...................................203
side view mirrors (power) .......41
Moon roof ....................................34
Motorcraft parts ........................204
Odometer .....................................13
Off road driving, 4-wheel
drive ....................................114,119
Overhead console
compass/temperature display ..33
storage compartment ...............33
Panic alarm feature, remote
entry system ................................47
Parking brake ............................102
Power door locks ........................40
Power steering
fluid, checking and adding ....167
Radio (see Electronic sound
systems) ......................................25
Rear window
washer .......................................32
Recreational towing, all wheels
on the ground ...........................133
Refill capacities for fluids ........204
Relays ........................................136
Remote entry system .................46
illuminated entry ......................49
locking/unlocking doors ......46,47
Index
214