length Mercury Mountaineer 1998 Owner's Manuals

WINDSHIELD WIPER/WASHER
CONTROLS
Rotate the windshield wiper
control to the desired interval, low
or high speed position.
The bars of varying length are for
intermittent wipers. When in this
position rotate the control upward
for fast intervals and downward for
slow intervals.
Push the control on the end of the
stalk to activate washer. Push and
hold for a longer wash cycle.
Speed dependent wipers
When the windshield wiper control
is set on the intermittent settings,
speed-sensitive front wipers
automatically adjust as the
vehicle's speed increases.
Rear window wiper and washer
For rear wiper operation, rotate
the rear window wiper and washer
control to the desired interval
position.
PUSH
OFFR.WIPE
HI
Controls and features
32

Do not place any objects
on the cargo area cover.
They may obstruct your vision or
strike occupants of the vehicle in
the case of a sudden stop or
collision.
Rewinding the shade
With extended use, the cargo
shade may lose its spring tension.
If this occurs, the shade must be
manually rewound. This is a
two-person operation.
1. Remove the shade from the
vehicle and extend it with the
smooth grain facing you.
2. Wrap the vinyl around the roller
tube twice. Tuck the edges of the
vinyl inside the end cap with each
wrap.
3. Fold the edges of the vinyl
towards the center, making sure
that the edges clear the end cap
slots. Use tape or a rubber band to
hold the vinyl to the left side of
the tube.
4. Push in the right end cap
(marked RH) about
1¤4of the total
length to disengage the clutch and
hold the end cap in while turning
the roller tube toward you 14
times.
Controls and features
45

Combination lap and shoulder
belts
1. To fasten, insert the tongue into
the slot in the buckle.
2. To unfasten, push the red
release button and remove the
tongue from the buckle.
The front and rear outboard safety
restraints in the vehicle are
combination lap and shoulder
belts. The front and rear seat
passenger outboard safety belts
have two types of locking modes
described below:
Vehicle sensitive mode
The vehicle sensitive mode is the
normal retractor mode, allowing
free shoulder belt length
adjustment to your movements and
locking in response to vehicle
movement. For example, if the
driver brakes suddenly or turns a
corner sharply, or the vehicle
Seating and safety restraints
68

applications must add 118ml
(4 oz.) of additive friction modifier
C8AZ-19B546±A, Ford specification
EST-M2C118±A to the rear axle
whenever the axle has been
serviced.
ENGINE DATA
Engine 5.0L engine 4.0L SOHC engine
Cubic inches 302 245
Horsepower 215 @ 4200 rpm 205 @ 5000 rpm
Torque 288 lbs.ft. @ 3300 rpm 250 lb. ft. @ 3000 rpm
Required fuel grade 87 octane 87 Octane
Firing order 1-3-7-2-6-5-4-8 1-4-2-5-3-6
Spark plug gap 1.3 mm-1.4 mm
(0.052-.056 inch)1.3 mm-1.4 mm
(0.052-.056 inch)
Ignition system EDIS EDIS
Compression ratio 9.0:1 9.7:1
VEHICLE DIMENSIONS
Dimensions mm (in.)
(1) Overall length 4 788 (188.5)
(2) Overall width 1 783 (70.2)
(3) Maximum height 1 725 (67.9)
(4) Wheelbase 2 835 (111.6)
(5) Front track/ rear 1 486/1487 (58.5/58.5)
Capacities and specifications
209