clock Mercury Mystique 1996 s User Guide

204
*
[SV06550(ALL)05/95]2.
Put the nozzle all the way inside the fuel filler pipe before
pumping the fuel.
*
[SV06625(ALL)05/95]
NOTE: If you spill any fuel on the body of your vehicle,
clean it off immediately. The fuel may dull or soften
the paint if you do not wash it off.
[SV06650(ALL)05/95]3.
Replace the fuel cap completely when you are finished. Turn
it clockwise until it is tight. It will click when it is fully
tightened.
*
[SV06675(ALL)05/95]4.
Push the fuel door closed.
*
[SV06690(ALL)06/95]
If you lose the fuel cap, replace it with an authorized Motorcraft
or equivalent part.
%*
[SV06700(ALL)05/95]
RWARNING
If you do not use the proper fuel cap, the pressure in the
fuel tank can damage the fuel system or cause it to work
improperly in a collision.
*
[SV06750(ALL)05/95]
NOTE: If you replace your fuel cap with an aftermarket fuel
filler cap, the customer warranty may be void for any
damage to the fuel tank and/or fuel system.
%*
[SV07500(ALL)05/95]
Choosing the Right Fuel
[SV07600(ALL)05/95]
Use only UNLEADED FUEL. The use of leaded fuel is
prohibited by law and could damage your vehicle. The damage
may not be covered by your warranty.
[SV07650(ALL)05/95]
Your vehicle was not designed to use fuel containing
manganese-based additives such as MMT. Additionally, vehicles
certified to California emission standards (indicated on the
underhood Vehicle Emissions Control Information label) are
designed to operate on California reformulated gasolines. If
California reformulated gasoline is not available when you
refuel, your vehicle can be operated on non-California fuels.
However, even though your engine will perform adequately on
other gasolines, the performance of the emission control devices
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

Servicing Your Mystique
215
*
[SV17850(ALL)01/95]
Check the engine coolant level in the engine coolant reservoir at
least once a month using the following guidelines.
[SV17900(ALL)01/95]
When your vehicle's engine is cool, the coolant level in the
engine coolant recovery reservoir should be at or above the
MIN mark. When the engine is hot, the coolant level should be
at the MAX mark. If the level is below the indicator mark in
either condition, coolant may need to be added.
*
[SV18000(ALL)05/95]
The coolant additives also protect the entire cooling system from
internal passageway corrosion and these additives lubricate the
water pump. The coolant should be serviced as noted in the
Maintenance Schedule and Recordbooklet.
*
[SV18100(ALL)01/95]
Adding engine coolant
*
[SV18200(ALL)05/95]
RWARNING
Do not put engine coolant in the container for the
windshield washer fluid.
*
[SV18300(ALL)05/95]
RWARNING
Never remove the coolant recovery cap while the engine
is running or hot.
[SV18500(ALL)01/95]1.
Before you remove the cap, turn the engine off and let it
cool. Even when the engine is cool, be careful when you
remove the coolant recovery cap.
[SV18600(ALL)05/95]2.
When the engine is cool, wrap a thick cloth around the cap
and turn it slowly counterclockwise to relieve the pressure.
*
[SV18700(ALL)03/95]3.
Step back while the pressure releases.
[SV18800(ALL)05/95]4.
When you are sure that all the pressure has been released,
use the cloth to turn and remove cap.
*
[SV18900(ALL)02/95]5.
Stand away from the reservoir opening. Hot steam may blow
out or hot engine coolant may even splash out.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

Servicing Your Mystique
245
*
[SV38800(ALL)03/95]
Headlamp Bulb
[SV38900(ALL)05/94]
The headlamps on your vehicle use replaceable bulbs, one for
high beam and one for low beam on each side. When the lamp
burns out, simply replace the bulb, rather than the whole lamp.
*
[SV39000(ALL)05/95]
RWARNING
Handle a halogen headlamp bulb carefully and keep out
of children's reach. Grasp the bulb only by its plastic
base and do not touch the glass. The oil from your hand
could cause the bulb to break the next time the
headlamps are operated.
*
[SV39100(ALL)01/95]
Do not remove the burned-out bulb unless you can immediately
replace it with a new one. If a bulb is removed for an extended
period of time, contaminants may enter the headlamp housing
and affect its performance.
*
[SV39300(ALL)03/95]
Removing the headlamp bulb
*
[SV39400(ALL)05/95]1.
Make sure that the headlamp knob is in the OFF position.
*
[SV39500(ALL)02/95]2.
Lift the hood and find the bulb in the headlamp socket.
[SV39850(ALL)04/94]3.
Remove the bulb assembly by turning it clockwise and
pulling it out of the headlamp socket.
[SV40050(ALL)04/94]4.
Remove the L-shaped bulb by pressing the retaining clip at
the base of the electrical connector and sliding the bulb out.
*
[SV40300(ALL)03/95]
Installing the headlamp bulb
[SV40450(ALL)04/94]1.
Without touching the glass on the bulb, insert the new bulb.
You may want to protect the bulb by holding it with a piece
of cloth or paper towel. Make sure the retaining clip at the
base of the electrical connector locks.
[SV40550(ALL)04/94]2.
Insert the bulb assembly in the headlamp socket. Turn it
counterclockwise to lock it in place.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

246
[SV40700(ALL)04/94]3.
Turn the headlamps on and make sure that they work
properly. If the headlamp was correctly aligned before you
changed the bulb, you should not need to align it again.
*
[SV40750(ALL)02/95]
High-Mount Brakelamp Bulbs
[SV40841(ALL)02/94]
From the back seat, remove the back of the brakelamp
assembly. Depress the two retaining tabs on the ends of the
assembly and pull off the back.
[SV40843(ALL)02/94]
Turn the burned-out bulb counterclockwise and pull it out. Push
in the replacement bulb and turn it clockwise to lock it in the
socket. Replace the back of the brakelamp assembly, making
sure that the retaining tabs snap into place.
[SV40848(ALL)02/94]
17-1/2 pica
art:0000624-B
The high-mount brakelamp assembly
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996