check engine Mercury Mystique 1996 s Owner's Guide

214
*
[SV17300(ALL)03/95]
Engine Coolant
%*
[SV17320(ALL)03/95]
Checking the Engine Coolant
*
[SV17350(ALL)01/95]
NOTE: Be sure to read and understandPrecautions When
Servicing Your Vehicleat the beginning of this chapter.
*
[SV17400(ALL)05/95]
RWARNING
The cooling fan is automatic and may come on at any
time. Always disconnect the negative terminal of the
battery before working near the fan.
[SV17720(ALL)05/95]
13-1/2 pica
art:0000336-D
The engine coolant recovery reservoir (2.5L shown Ð 2.0L similar)
%*
[SV17825(ALL)05/94]
Your vehicle's coolant protects your engine from overheating in
the summer and from freezing in the winter. Check the level of
the coolant at least once a month. Simply look at the engine
coolant reservoir located in the engine compartment. To locate
the reservoir, see the diagram of your vehicle's engine under
Engine Type, in this chapter.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

Servicing Your Mystique
215
*
[SV17850(ALL)01/95]
Check the engine coolant level in the engine coolant reservoir at
least once a month using the following guidelines.
[SV17900(ALL)01/95]
When your vehicle's engine is cool, the coolant level in the
engine coolant recovery reservoir should be at or above the
MIN mark. When the engine is hot, the coolant level should be
at the MAX mark. If the level is below the indicator mark in
either condition, coolant may need to be added.
*
[SV18000(ALL)05/95]
The coolant additives also protect the entire cooling system from
internal passageway corrosion and these additives lubricate the
water pump. The coolant should be serviced as noted in the
Maintenance Schedule and Recordbooklet.
*
[SV18100(ALL)01/95]
Adding engine coolant
*
[SV18200(ALL)05/95]
RWARNING
Do not put engine coolant in the container for the
windshield washer fluid.
*
[SV18300(ALL)05/95]
RWARNING
Never remove the coolant recovery cap while the engine
is running or hot.
[SV18500(ALL)01/95]1.
Before you remove the cap, turn the engine off and let it
cool. Even when the engine is cool, be careful when you
remove the coolant recovery cap.
[SV18600(ALL)05/95]2.
When the engine is cool, wrap a thick cloth around the cap
and turn it slowly counterclockwise to relieve the pressure.
*
[SV18700(ALL)03/95]3.
Step back while the pressure releases.
[SV18800(ALL)05/95]4.
When you are sure that all the pressure has been released,
use the cloth to turn and remove cap.
*
[SV18900(ALL)02/95]5.
Stand away from the reservoir opening. Hot steam may blow
out or hot engine coolant may even splash out.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

216
*
[SV19000(ALL)01/95]
RWARNING
Failure to follow these instructions could result in serious
personal injury from hot engine coolant or steam
blowout and/or damage to the engine cooling system or
engine.
*
[SV19025(ALL)03/95]
To find out how much engine coolant mixture your vehicle's
coolant system can hold, seeRefill capacities for fluidsin the
Index.
*
[SV19100(ALL)01/95]
Have your dealer check the engine cooling system for leaks if
you have to add a quart (liter) of engine coolant more than
once a month.
*
[SV19102(ALL)06/95]
Add engine coolant only to the recovery reservoir.If the
coolant level is low, add to the reservoir a 50/50 mixture of
water and the type of engine coolant that Ford specifies. You
may add water by itself only in an emergency, but you should
replace it with a 50/50 mixture as soon as possible. Check the
engine coolant again the next few times you drive your vehicle.
*
[SV19104(ALL)02/95]
Ford Premium Cooling System Fluid is an optimized formula
that will protect all metals and rubber elastomers used in Ford
engines for four years or 50,000 miles (80,000 km). It is not
necessary and not recommended to use supplemental coolant
additives in your vehicle. These additives may harm your
engine cooling system. Follow the recommended service interval
for changing your engine coolant.
*
[SV19106(ALL)04/94]
NOTE: When you change or add engine coolant, it is
important to maintain your engine coolant
concentration between 40%(-11ÊF [-24ÊC]) and 60%
(-62ÊF [-52ÊC]),depending on your local climate
conditions. Below 40% you will lose freeze protection
and above 60% your engine may overheat on a warm
day.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

220
*
[SV20700(ALL)03/95]
If you do not let the engine relearn its idle, the idle quality of
your vehicle may be adversely affected until the idle is
relearned. Your vehicle will eventually relearn its idle while you
drive it, but it takes much longer than if you use the previous
procedure.
*
[SV21700(ALL)03/95]
Windshield Washer Fluid and Wipers
*
[SV21800(ALL)03/95]
Washer Fluid
*
[SV22100(ALL)01/95]
Check the level of the windshield washer fluid every time you
stop for fuel. The reservoir for washer fluid is located on the
passenger's side of the engine compartment. Visual inspection
can determine if the washer fluid is adequate. Do not operate
the washer when the reservoir is empty.
[SV22200(ALL)02/94]
10-1/2 pica
art:0001222-A
The windshield washer fluid reservoir
*
[SV22300(ALL)03/95]
Adding washer fluid
*
[SV22400(ALL)05/95]
RWARNING
Do not put windshield washer fluid in the container for
the engine coolant.
[SV22450(ALL)05/95]
If sprayed to clean the glass, engine coolant or antifreeze could
make it difficult to see through the windshield.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

230
*
[SV29300(ALL)03/01]
Automatic Transaxle Fluid
*
[SV29310(ALL)03/95]
Under normal circumstances, you do not need to check the fluid
level of the transaxle, since your vehicle does not use up
transaxle fluid. Refer to theMaintenance Schedule and Record
booklet for replacement intervals. However, if the transaxle is
not working properly Ð for instance, the transaxle may slip or
shift slowly, or you may notice some sign of fluid leakage Ð
the fluid level should be checked.
%*
[SV29340(ALL)02/93]
Checking the Automatic Transaxle Fluid
*
[SV29350(ALL)01/95]
With the vehicle on a level surface and the brake fully applied,
start the engine and move the gear shift selector through all of
the gears allowing sufficient time for each position to engage.
Securely latch the gear shift selector in the P (Park) position.
Fully set the parking brake and leave the engine running.
*
[SV29370(ALL)01/95]
Wipe off the dipstick cap and pull the dipstick out. Wipe the
indicator end clean. Put the dipstick back into the filler tube and
make sure it is fully seated. Pull the dipstick out and read the
fluid level.
*
[SV29372(ALL)01/95]
NOTE: Your vehicle should not be driven until some fluid
has been added if the fluid level is below the bottom
dimple on the dipstick and the outside temperature is
above50ÊF (10ÊC). Addonly enough fluid to bring the
level above the bottom hole.
*
[SV29376(ALL)02/95]
If the vehicle has not been driven and the fluid level is above
the bottom dimple on the dipstick, do not add fluid. Recheck
the fluid level after your vehicle has reached normal operating
temperature.
*
[SV29378(ALL)05/95]
Normal operating temperature is reached after driving
approximately 20 miles (30 km). The fluid level should be
within the crosshatched area on the dipstick.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

232
[SV29800(ALL)02/95]
Manual Transaxle Fluid
[SV29900(ALL)05/94]
The lubricant level and quality should not deteriorate under
normal driving conditions. However, you should have the fluid
level checked occasionally. If lubricant is required, seeLubricant
Specificationsin this chapter.
*
[SV30200(ALL)03/95]
Brake Fluid
*
[SV30300(ALL)04/95]
Under normal circumstances, your vehicle should not use up
brake fluid rapidly. However, expect the level of the brake fluid
to slowly fall as you put more mileage on your vehicle and the
brake lining wears.
[SV30401(ALL)02/94]
You should check the brake fluid at every scheduled engine oil
change, but be sure to check it at least once a year. You can do
this by looking at the fluid level in the plastic reservoir on the
master cylinder. (SeeThe Engine Typesin this chapter to locate
the brake fluid reservoir.) The fluid level should be at or near
the MAX mark.
*
[SV30450(ALL)05/95]
RWARNING
Brake fluid is toxic.
*
[SV30475(ALL)06/95]
If brake fluid contacts eyes, flush eyes with running water for
15 minutes. Get medical attention if irritation persists. If taken
internally, drink water and induce vomiting. Get medical
attention immediately.
*
[SV30500(ALL)03/95]
If the fluid is low, carefully clean and remove the cap from the
reservoir. Fill the reservoir to the MAX line with Ford High
Performance DOT 3 Brake Fluid C6AZ-19542-AA or equivalent
DOT 3 fluid meeting Ford specification ESA-M6C25-A.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

234
*
[SV31200(ALL)03/95]
Power Steering Fluid
*
[SV31225(ALL)03/95]
Checking and Adding Power Steering Fluid
[SV31250(ALL)05/94]
With the power steering system at operating temperature,
switch off the engine. The fluid level should be up to the MAX
marking on the transparent reservoir.
[SV31275(ALL)05/94]
If it drops to or below the MIN mark, top off with the specified
fluid.
[SV31350(ALL)05/94]
10-1/2 pica
art:0001260-A
The power steering fluid reservoir
[SV32000(ALL)05/95]
Use only power steering fluid that meets Ford's Specification
ESW-M2C33-F or is an equivalent Type F Automatic
Transmission Fluid with a Ford registration number (an 8-digit
number beginning with ª2Pº printed on the fluid container).
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

Servicing Your Mystique
249
*
[SV41800(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[SV41900(ALL)05/95]
Watch for fluid leaks, strange odors, smoke, loss of oil pressure,
the charge warning light, the check engine light, or the
temperature warning light. These sometimes indicate that the
emission system is not working properly.
*
[SV42000(ALL)01/95]
Do not make any unauthorized changes to your vehicle or
engine. Changes that cause more unburned fuel to reach the
exhaust system can increase the temperature of the engine or
exhaust system.
*
[SV42100(ALL)01/95]
By law, anyone who manufactures, repairs, services, sells, leases,
trades vehicles, or supervises a fleet of vehicles is not permitted
to intentionally remove an emission control device or prevent it
from working. In some of the United States and in Canada,
vehicle owners may be liable if their emission control device is
removed or is prevented from working.
*
[SV42300(ALL)01/95]
Do not drive your vehicle if it does not operate properly. See
your dealer if the engine runs on for more than five seconds
after you shut it off or if it misfires, surges, stalls, or backfires.
%*
[SV42400(ALL)05/95]
Information about your vehicle's emission control system is on
the Vehicle Emission Control Information decal located on or
near the engine. This decal identifies engine displacement and
gives some tune-up specifications.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

250
%*
[SV42425(ALL)06/95]
Readiness for Inspection/Maintenance Testing
*
[SV42450(ALL)06/95]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is reset to a not ready
for I/M testing condition. To prepare for I/M testing, the law
specifies a ªneed for additional mixed city and highway driving
to complete the checkº of the OBD II system. As soon as all of
the OBD II system checks are successfully completed, the OBD
II system is set to the ready condition. The amount of driving
required to reach the ready condition varies with individual
driving patterns. To complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle defined below.
If the vehicle owner cannot or does not want to do the
additional driving required by law, a service center can perform
this drive cycle as it would any other type of repair work.
*
[SV42475(ALL)06/95]
OBD II Drive Cycle
*
[SV42501(ALL)06/95]
The following steps must be run in the order shown. If any
steps are interrupted, repeat the preceding step. Any safe
driving mode is acceptable between steps.
*
[SV42550(ALL)06/95]
Always drive vehicle in safe manner according to traffic
conditions and obey all traffic laws.
*
[SV42560(ALL)05/95]
The engine must be warmed up and at operating temperature
before proceeding with the drive modes of the following OBD II
Drive Cycle.
*
[SV42575(ALL)05/95]1.
Start the engine. Drive or idle (in neutral) the vehicle for
4 minutes.
[SV42601(ALL)05/95]2.
Idle the vehicle in Drive (Neutral for manual transaxle) for
40 seconds.
*
[SV42610(ALL)06/95]3.
Accelerate the vehicle to 45 mph (70 km/h) at 1/4 to 1/2
throttle for 10 seconds.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996

256
%*
[SV45350(ALL)01/95]
Engine
*
[SV45400(ALL)01/95]
n
Start engine every 15 days. Run at fast idle until it reaches
normal operating temperature.
*
[SV45500(ALL)01/95]
n
With your foot on the brake, shift through all the gears
while the engine is running.
%*
[SV45600(ALL)01/95]
Fuel system
%*
[SV45700(ALL)07/94]
n
Fill fuel tank with high-quality unleaded fuel until the first
automatic shutoff of the fuel pump nozzle.
*
[SV45900(ALL)03/95]
NOTE: During extended periods of vehicle storage (60 days or
more), fuel may deteriorate due to oxidation. This can
damage rubber and other polymers in the fuel system
and may also clog small orifices.
*
[SV46000(ALL)01/95]
Ford Gas Stabilizer should be added whenever actual or
expected storage periods exceed 60 days. Follow the instructions
on the label. The vehicle should then be operated at idle speed
to circulate the additive throughout the fuel system.
*
[SV46100(ALL)01/95]
A volatile corrosion inhibitor added to the fuel system will
protect the fuel system's inner surfaces from corrosion. Follow
the instructions packaged with the product.
%*
[SV46200(ALL)01/95]
Cooling system
*
[SV46300(ALL)01/95]
n
Protect against freezing temperatures.
%*
[SV46400(ALL)01/95]
Battery
*
[SV46500(ALL)01/95]
n
Check and recharge as necessary.
*
[SV46600(ALL)01/95]
n
Keep connections clean and covered with a light coat of
grease.
*
[SV46650(ALL)03/95]
n
If storing your vehicle for more than 30 days without
recharging the battery, it may be advisable to disconnect the
battery cables to ensure battery charge is maintained for
quick starting.
File:cdsvz.ex
Update:Fri Feb 23 11:01:54 1996