engine Mercury Mystique 1996 Owner's Manuals

4
%*
[IN04000(ALL)01/95]
Buying a Ford Extended Service Plan
*
[IN04100(ALL)01/94]
If you bought your vehicle in the U.S., you can buy a Ford
Extended Service Plan for your vehicle. This optional contract
provides service protection for a longer period of time than the
basic warranty that comes with your vehicle.
*
[IN04200(ALL)01/95]
You do not have to buy this option when you buy your vehicle.
However, your option to purchase the Ford Extended Service
Plan runs out after 18 months or 18,000 miles. See your dealer
for more details about the Ford Extended Service Plan.
*
[IN04250(ALL)01/95]
If you purchased a Canadian vehicle and did not take
advantage of the Ford Extended Service Plan at the time of
purchase, you may still be eligible. See your dealer for the
details.
*
[IN06000(ALL)01/95]
Breaking Your Vehicle In
*
[IN06100(ALL)03/95]
Your new vehicle goes through an adjustment or break-in
period during the first 1,000 miles (1,600 km) that you drive it.
During the break-in period, you need to pay careful attention to
how you drive your vehicle.
%*
[IN06300(ALL)01/95]
n
Avoid sudden stops.Because your vehicle has new brake
linings, you should take these steps:
*
[IN06400(ALL)01/95]
Ð Watch traffic carefully so that you can anticipate when to
stop.
*
[IN06500(ALL)01/95]
Ð Begin braking well in advance.
*
[IN06600(ALL)01/95]
Ð Apply the brakes gradually.
*
[IN06700(ALL)01/95]
The break-in period for new brake linings lasts for 100 miles
(160 km) of city driving or 1,000 miles (1,600 km) of
highway driving.
%*
[IN06800(ALL)01/95]
n
Use only the type of engine oil that Ford recommends.See
Engine oil recommendationsin the Index. Do not use special
ªbreak-inº oils.
File:cdinz.ex
Update:Fri Feb 23 11:09:48 1996

42
[ST04400(ALL)05/94]
ACCESSORY allows some of your vehicle's electrical accessories
to operate while the engine is not running. For example, you
can use ACCESSORY to turn on the radio without starting the
engine.
*
[ST04425(ALL)05/95]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[ST04450(ALL)03/95]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
%*
[ST04500(ALL)02/95]
Removing the Key From the Ignition
*
[ST04600(ALL)05/94]
Procedures for removing your key from the ignition vary,
depending on whether your vehicle has an automatic or manual
transaxle.
*
[ST04700(ALL)04/94]
If your vehicle has an automatic transaxle:
*
[ST04800(ALL)06/92]1.
Put the gearshift lever in P (Park).
*
[ST04900(ALL)01/95]2.
Set the parking brake fully.
[ST05000(ALL)05/94]3.
Rotate the ignition key to the LOCK position.
[ST05100(ALL)02/95]4.
Remove the key from the ignition.
*
[ST05200(ALL)04/94]
If your vehicle has a manual transaxle:
*
[ST05300(ALL)06/92]1.
Put the gearshift lever in 1 (First).
*
[ST05400(ALL)01/95]2.
Set the parking brake fully.
[ST05701(ALL)05/94]3.
Rotate the ignition key to the LOCK position.
[ST05801(ALL)02/95]4.
Remove the key from the ignition.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

Starting Your Mystique
43
[ST07325(ALL)04/94]
The steering wheel locks when the key is removed.
%*
[ST07400(ALL)05/95]
If the driver's door is open while the key is still in the ignition,
a warning chime sounds.
*
[ST07500(ALL)05/95]
RWARNING
Always set the parking brake fully and make sure that
the gearshift is securely latched in P (Park) (automatic
transaxle) or in 1 (First) (manual transaxle).
*
[ST07575(ALL)01/93]
RWARNING
Do not leave children, unreliable adults, or pets alone in
your vehicle. They could accidentally injure themselves
or others through inadvertent operation of the vehicle.
Further, on hot, sunny days, temperatures in a closed
vehicle could quickly become high enough to cause
severe and possibly fatal injuries to people as well as
animals.
%*
[ST07700(ALL)03/95]
Fuel-Injected Engines
*
[ST07850(ALL)03/95]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

44
*
[ST08200(ALL)03/95]
Starting Your Vehicle
%*
[ST08300(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST08350(ALL)05/95]
RWARNING
Do not start your vehicle in a closed garage or other
enclosed area. Never sit in a stopped vehicle for more
than a short period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding Against Exhaust
Fumesin this chapter for more instructions.
*
[ST08400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST08500(ALL)01/95]1.
Make sure you and all your passengers buckle your safety
belts. SeeSafety Restraintsin the Index for more details.
*
[ST08600(ALL)03/95]2.
Make sure your headlamps and other accessories are turned
off and the parking brake is set.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

Starting Your Mystique
45
[ST08800(ALL)05/94]3.
If you have a manual transaxle,make sure that the parking
brake is fully set, push the clutch pedal to the floor, and put
the gearshift into Neutral before you turn the key.
(Remember, the starter will operate only if the clutch pedal
is pushed all the way to the floor.)
[ST08900(ALL)12/94]
If you have an automatic transaxle,make sure that the
gearshift is in P (Park) and the parking brake is set before
you turn the key.
*
[ST09100(ALL)03/95]
Before you start your vehicle, you should test the warning lights
on the instrument panel to make sure that they work. Refer to
theWarning Lights and Gaugeschapter.
*
[ST09310(ALL)02/95]
Starting Your Engine
*
[ST09320(ALL)02/95]
To start your engine:
*
[ST09330(ALL)05/95]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[ST09340(ALL)03/95]2.
Keep your foot on the brake pedal and turn the ignition key
to the ON position.
*
[ST09350(ALL)03/95]3.
DO NOT depress the accelerator pedal when starting your
engine. DO NOT use the accelerator while the vehicle is
parked.
*
[ST09360(ALL)02/95]4.
Turn the key to the START position (cranking) until the
engine starts. Allow the key to return to the ON position
after the engine has started.
*
[ST09370(ALL)02/95]
If you have difficulty in turning the key, rotate the steering
wheel slightly because it may be binding.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

46
%*
[ST09372(ALL)04/95]
For a cold engine:
[ST09375(ALL)05/95]
2.0L engine:
[ST09380(ALL)06/95]
n
At temperaturesbelow-10ÊF (-23ÊC):Turn the key to ON,
crank the engine and depress the accelerator about 1/4 of
the way down and hold that position forfive (5) seconds.If
the engine fails to start, continue to crank with the
accelerator depressed about 1/4 of the way down and hold
that position until the engine starts.DO NOT crank for
more than 30 seconds,or you could damage the starter. If
the engine fails to start on the first try, turn the key to OFF
and wait two (2) minutes before trying again. Allow engine
to warm up for a few minutes before putting transaxle into
gear.
[ST09385(ALL)05/95]
n
At temperaturesbetween-10ÊF (-23ÊC) and 10ÊF(-12ÊC):
Turn the key to ON, and crank the engine forfive (5)
seconds.If the engine fails to start, continue to crank and
depress the accelerator about 1/4 of the way down and hold
that position until the engine starts.DO NOT crank for
more than 30 seconds,or you could damage the starter. If
the engine fails to start on the first try, turn the key to OFF
and wait two (2) minutes before trying again.
[ST09391(ALL)05/95]
n
At temperaturesbetween10ÊF (-12ÊC) and 32ÊF (0ÊC):If the
engine does not start infifteen (15) secondson first try, turn
the key to OFF, then try again.
[ST09395(ALL)05/95]
n
At temperaturesabove32ÊF (0ÊC):If the engine does not
start infive (5) secondson the first try, turn the key to OFF,
then try again.
[ST09401(ALL)05/95]
If you have the 4-cylinder 2.0L engine and are not using an
engine block heater, warm up the engine for a minute or two
before putting the transaxle in gear. Depressing the accelerator
slightly will also help with cold starts.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

Starting Your Mystique
47
[ST09405(ALL)05/95]
2.5L engine:
*
[ST09411(ALL)05/95]
n
At temperatures10ÊF (-12ÊC) andbelow:If the engine does
not start infifteen (15) secondson the first try, turn the key
to OFF, wait approximately ten (10) seconds so you do not
flood the engine, then try again.
[ST09415(ALL)05/95]
n
At temperaturesabove10ÊF(-12ÊC):If the engine does not
start infive (5) secondson the first try, wait approximately
ten (10) seconds so you do not flood the engine, then try
again.
%*
[ST09421(ALL)05/95]
For a warm engine:
[ST09425(ALL)05/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, wait a few seconds after the
starter stops, then try again.
*
[ST09430(ALL)05/95]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter or
flood the engine.
*
[ST09435(ALL)05/95]
After you start the engine, let it idle for a few seconds. Keep
your foot on the brake pedal and put the gearshift lever in gear.
Release the parking brake. Slowly release the brake pedal and
drive away in the normal manner.
*
[ST09440(ALL)05/95]
NOTE: If your vehicle is equipped with an automatic
transaxle, your vehicle has an interlock that prevents
you from shifting out of P (Park) unless your foot is
on the brake pedal.
%*
[ST09480(ALL)04/95]
If the engine does not start after two attempts:
[ST09494(ALL)01/95]1.
Press the accelerator pedal all the way to the floor and hold it.
[ST09496(ALL)01/95]2.
Turn the ignition key to the START position.
[ST09497(ALL)01/95]3.
Release the ignition key when the engine starts.
[ST09498(ALL)01/95]4.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

48
*
[ST09500(ALL)04/95]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchlater in this chapter.
%*
[ST10200(ALL)05/95]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle move slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[ST10250(ALL)05/95]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
*
[ST10325(ALL)05/95]
RWARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
*
[ST10350(ALL)05/95]
RWARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up
the engine compartment and exhaust system, which can
start a fire.
*
[ST10500(ALL)03/95]
If you consistently start your vehicle in subzero temperatures,
use an engine block heater (if your vehicle has this option).
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

Starting Your Mystique
49
%*
[ST10600(ALL)06/95]
Engine Block Heater (If equipped)
*
[ST10700(ALL)03/95]
Engine block heaters are strongly recommended if you live in a
region where temperatures reach-10ÊF (-23ÊC) orbelow. An
engine block heater warms the engine coolant, which improves
starting, warms up the engine faster, and allows the
heater-defrost system to respond quickly.
*
[ST10900(ALL)01/95]
To turn the heater on, simply plug it into a grounded 110-volt
outlet. Ford recommends that you use a 110-volt circuit that is
protected by a ground fault circuit interrupter.
*
[ST11100(ALL)05/95]
RWARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
*
[ST11150(ALL)03/95]
For best results, plug the heater in at least three hours before
you start your vehicle. Using the heater for longer than three
hours will not damage the engine, so you can plug it in at night
to start your vehicle the following morning.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

50
*
[ST11200(ALL)03/95]
If the Engine Cranks but Does Not Start or
Does Not Start After a Collision
%*
[ST11300(ALL)04/95]
Fuel Pump Shut-off Switch
*
[ST11400(ALL)03/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a substantial
jolt.
[ST11500(ALL)01/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle. The switch is located
on the left hand kick panel in the driver's footwell.
[ST11600(ALL)01/95]
13-1/2 pica
art:0000530-D
The left-hand kick panel in the driver's footwell
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996