ECO mode Mercury Sable 1996 s User Guide
[x] Cancel search | Manufacturer: MERCURY, Model Year: 1996, Model line: Sable, Model: Mercury Sable 1996Pages: 391, PDF Size: 3.26 MB
Page 247 of 391
![Mercury Sable 1996 s User Guide 220
*
[RE02900(ALL)03/95]
RWARNING
Do not connect the end of the second
cable to the negative (s) terminal of
the discharged battery. If you do, a
spark may cause an explosion of the
gases that normal Mercury Sable 1996 s User Guide 220
*
[RE02900(ALL)03/95]
RWARNING
Do not connect the end of the second
cable to the negative (s) terminal of
the discharged battery. If you do, a
spark may cause an explosion of the
gases that normal](/img/33/11168/w960_11168-246.png)
220
*
[RE02900(ALL)03/95]
RWARNING
Do not connect the end of the second
cable to the negative (s) terminal of
the discharged battery. If you do, a
spark may cause an explosion of the
gases that normally surround the
battery and could seriously injure
someone.
[RE03100(ALL)04/95]
one third page art:0000388-D
Jumper cable connections
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[RE03700(ALL)03/95]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[RE03800(ALL)03/95]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995
Page 354 of 391
![Mercury Sable 1996 s User Guide 327 %
*
[SV42405(ALL)03/95]
Readiness for Inspection/Maintenance
Testing
*
[SV42410(ALL)03/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
Mercury Sable 1996 s User Guide 327 %
*
[SV42405(ALL)03/95]
Readiness for Inspection/Maintenance
Testing
*
[SV42410(ALL)03/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the](/img/33/11168/w960_11168-353.png)
327 %
*
[SV42405(ALL)03/95]
Readiness for Inspection/Maintenance
Testing
*
[SV42410(ALL)03/95]
In some localities it may become a legal
requirement to pass an
Inspection/Maintenance (I/M) test of the
On-Board Diagnostic (OBD) II system. If the
vehicle's powertrain system or its battery has
just been serviced, the OBD II system is reset to
a not ready for I/M testing condition. To
prepare for I/M testing, the law specifies a
ªneed for additional mixed city and highway
driving to complete the checkº of the OBD II
system. As soon as all of the OBD II system
checks are successfully completed, the OBD II
system is set to the ready condition. The amount
of driving required to reach the ready condition
varies with individual driving patterns. To
complete this requirement in the minimum
amount of time, refer to the OBD II Drive Cycle
defined below. If the vehicle owner cannot or
does not want to do the additional driving
required by law, a service center can perform
this drive cycle as it would any other type of
repair work.
*
[SV42420(ALL)03/95]
OBD II Drive Cycle
*
[SV42430(ALL)04/95]
The following steps must be run in the order
shown. If any steps are interrupted, repeat the
preceding step. Any safe driving mode is
acceptable between steps.
*
[SV42440(ALL)03/95]
Always drive vehicle in safe manner according
to traffic conditions and obey all traffic laws.
[SV42445(ALL)04/95]
The engine must be warmed up and at
operating temperature before proceeding with
the drive modes of the following OBD II Drive
Cycle.
*
[SV42450(ALL)04/95]
1. Start the engine. Drive or idle (in neutral)
the vehicle for 4 minutes.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995
Page 355 of 391
![Mercury Sable 1996 s User Guide 328
*
[SV42460(ALL)04/95]
2. Idle the vehicle in Drive for 40 seconds.
*
[SV42465(ALL)04/95]
3. Accelerate the vehicle to 45 mph (72 km/h)
at 1/4 to 1/2 throttle for 10 seconds.
*
[SV42471(ALL)04/95]
Mercury Sable 1996 s User Guide 328
*
[SV42460(ALL)04/95]
2. Idle the vehicle in Drive for 40 seconds.
*
[SV42465(ALL)04/95]
3. Accelerate the vehicle to 45 mph (72 km/h)
at 1/4 to 1/2 throttle for 10 seconds.
*
[SV42471(ALL)04/95]](/img/33/11168/w960_11168-354.png)
328
*
[SV42460(ALL)04/95]
2. Idle the vehicle in Drive for 40 seconds.
*
[SV42465(ALL)04/95]
3. Accelerate the vehicle to 45 mph (72 km/h)
at 1/4 to 1/2 throttle for 10 seconds.
*
[SV42471(ALL)04/95]
4. Drive the vehicle with a steady throttle at
45 mph (72 km/h) for 30 seconds.
[SV42475(ALL)04/95]
5. Idle the vehicle in drive for 40 seconds.
*
[SV42481(ALL)04/95]
6. Continue to drive the vehicle in city traffic at
speeds between 25 and 40 mph
(40-64 km/h) for 15 minutes. During the 15
minute drive cycle the following modes must
be achieved:
*
[SV42485(ALL)04/95]
a. at least 5 stop and idle modes at 10
seconds each
*
[SV42491(ALL)04/95]
b. acceleration from idles at 1/4 to 1/2
throttle position, and
*
[SV42495(ALL)04/95]
c. choose 3 different speeds to do 1.5
minute steady state throttle drives.
*
[SV42500(ALL)04/95]
7. Accelerate the vehicle up to between 45 and
60 mph (72-97 km/h). This should take
approximately 5 minutes.
*
[SV42505(ALL)04/95]
8. Drive vehicle and hold the throttle steady at
the selected speed between 45 and 60 mph
(72-97 km/h) for approximately 5 minutes.
*
[SV42510(ALL)04/95]
9. Drive the vehicle for 5 minutes at varying
speeds between 45 and 60 mph
(72-97 km/h).
*
[SV42515(ALL)04/95]
10. Bring the vehicle back to idle. Idle in drive
for 40 seconds.
*
[SV42601(ALL)04/95]
11. OBD II drive cycle has been completed.
Vehicle can be turned off when convenient.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995