clock Mercury Sable 1996 s User Guide

263 %
*
[SV05075(ALL)04/95]
Cleaning the Engine
*
[SV06000(ALL)04/95]
A clean engine is more efficient because the
engine is able to cool properly. A build up of
grease and dirt acts as an insulator, keeping the
engine warmer than normal.
*
[SV06020(ALL)04/95]
q
Extreme care must be used if a power washer
is used to clean the engine. The high pressure
fluid could penetrate sealed parts and
assemblies causing damage or malfunctions.
*
[SV06040(ALL)04/95]
q
In order to avoid possible cracking of the
engine block or fuel injection pump, do not
spray a hot engine or injection pump with
cold water.
*
[SV06060(ALL)04/95]
q
The alternator, distributor and air intake must
be covered. Covering these components will
help prevent water damage.
*
[SV06080(ALL)04/95]
q
Never wash or rinse the engine while it is
running. Water getting into the engine may
cause internal damage.
%
*
[SV06100(ALL)03/95]
Filling the Fuel Tank
[SV06800(ALL)04/95]
1. Turn the engine off. After opening the fuel
door, remove the cap carefully and slowly
by turning it counterclockwise 1/4 turn until
it stops. Pull to remove the cap. A tether
attaches the cap to the fuel filler pipe.
[SV06825(ALL)04/95]
one inch art:0001470-AFile:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

264 [SV06850(ALL)04/95]
RWARNING
The fuel system may be under
pressure. If the fuel cap is venting
vapor or if you hear a hissing sound,
wait until it stops before completely
removing the cap. Otherwise, fuel
may spray out and injure you or
others.
*
[SV06900(ALL)03/95]
2. Make sure that you pump unleaded fuel and
put the nozzle all the way inside the fuel
filler pipe.
*
[SV06950(ALL)02/95]
NOTE: To help reduce early nozzle shutoffs
and fuel spillage, park your vehicle so
that the fuel filler door is not
downhill. Do not tilt or turn the nozzle
upside down when filling. Avoid
excessively fast fuel dispensing rates
(over 10 gallons [38 liters] per minute).
*
[SV07150(ALL)01/95]
3. If you spill any fuel on the body of your
vehicle, clean it off immediately. The fuel
may dull or soften the paint if you do not
wash it off.
[SV07200(ALL)11/94]
4. To replace the fuel cap, align the tabs on the
cap with the notches on the filler pipe. Turn
it clockwise until it stops.
[SV07250(ALL)04/95]
5. Push the fuel door closed.
[SV07275(ALL)04/95]
If the Service Engine Soon warning light comes
on and stays on when you start the engine, the
fuel cap may not be properly seated. Turn off
the engine, remove the fuel cap and replace it,
being careful to align the cap properly. For more
information, seeWarning lightsin the Index.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

278
*
[SV18100(ALL)01/95]
Adding engine coolant
*
[SV18200(ALL)01/95]
RWARNING
Be careful when adding engine
coolant. Do not put engine coolant or
antifreeze in the container for the
windshield washer fluid. If sprayed
to clean the glass, engine coolant or
antifreeze could make it difficult to
see through the windshield.
[SV18300(ALL)11/94]
RWARNING
Never remove the pressure cap while
the engine is running or hot to avoid
personal injury that can be caused by
escaping steam or engine coolant.
[SV18500(ALL)04/95]
1. Before you remove the cap, turn the engine
off and let it cool. Even when the engine is
cool, be careful when you remove the cap.
[SV18600(ALL)02/95]
2. When the engine is cold, wrap a thick cloth
around the cap and turn it slowly
counterclockwise to relieve pressure.
*
[SV18700(ALL)03/95]
3. Step back while the pressure releases.
*
[SV18800(ALL)03/95]
4. When you are sure that all the pressure has
been released, use the cloth to turn and
remove cap.
*
[SV18900(ALL)02/95]
5. Stand away from the reservoir opening. Hot
steam may blow out or hot engine coolant
may even splash out.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

316
*
[SV39300(ALL)03/95]
To remove the headlamp bulb:
*
[SV39350(ALL)08/95]
1. Make sure that the headlamp knob is in the
OFF position.
[SV39401(ALL)04/95]
2. Lift the hood. If you are replacing the
driver's side headlamp, unclip the electronic
module on the right side of the battery and
move it out of the way. Find the bulb in the
headlamp socket.
[SV39425(ALL)04/95]
one third page art:0001437-A
The module behind the driver's side headlamp
*
[SV39450(ALL)02/95]
3. Remove the electrical connector from the
bulb by pulling the connector.
*
[SV39501(ALL)02/95]
4. Remove the bulb retaining ring by rotating it
counterclockwise (when viewed from the
rear) about an eighth of a turn to free it
from the bulb socket, and by sliding the ring
off the plastic base. Keep the ring. It is to be
used again to retain the new bulb.
[SV39550(ALL)02/95]
5. Carefully remove the bulb from its socket by
gently pulling it straight back out of the
socket. Do not turn the bulb while you
remove it.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

317
*
[SV39601(ALL)03/95]
To install a bulb:
*
[SV39650(ALL)02/95]
1. With the flat side of the bulb's plastic base
facing upward, insert the glass end of the
bulb into the socket. You may need to turn
the bulb left or right to line up the grooves
in the plastic base with the tabs in the
socket. When the grooves are aligned, push
the bulb into the socket until the plastic base
contacts the rear of the socket.
*
[SV39701(ALL)02/95]
2. Slip the bulb retaining ring over the plastic
base until it contacts the rear of the socket.
Lock the ring into the socket by rotating it
clockwise until you feel a ªstopº.
*
[SV39750(ALL)02/95]
3. Push the electrical connector into the rear of
the plastic base until it snaps, locking it into
position.
*
[SV39800(ALL)02/95]
4. Turn the headlamps on and make sure that
they work properly. If the headlamp was
correctly aligned before you changed the
bulb, you should not need to align it again.
%*
[SV39850(ALL)02/95]
Aiming Headlamps
[SV39901(ALL)02/95]
Your vehicle is equipped with a Vehicle
Headlamp Aim Device (VHAD) on the
headlamp reflector extension and headlamp
housing. Each headlamp may be properly aimed
in the horizontal direction (left/right) and the
vertical direction (up/down) by performing the
steps outlined in the following paragraphs. The
horizontal aim must be adjusted first.
*
[SV39950(ALL)02/95]
Tools required: One 4mm box wrench or open
end wrench.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

319
*
[SV40201(ALL)02/95]
Horizontal aim adjustment
[SV40250(ALL)04/95]
1. Open the hood and locate the horizontal
indicator and adjusting screw.
*
[SV40375(ST)04/95]
2. Use a 4mm wrench to turn the horizontal
adjusting screw until the reference mark on
the reflector extension aligns with the ª0º
reference mark on the horizontal indicator
when viewed from directly above. If the
vehicle has been in an accident requiring the
front end of the vehicle to be repaired, the
horizontal indicator should be recalibrated
by a servicing facility using theTaurus/Sable
Service Manualinstructions.
*
[SV40501(ALL)02/95]
Vertical aim adjustment
*
[SV40601(ALL)02/95]
1. With the hood open, locate the bubble level
vertical aim indicator. It is visible when
viewed from above and to the rear of the
headlamp.
*
[SV40650(ALL)02/95]
2. With the vehicle on a level surface, use a
4mm wrench to turn the vertical aim
adjustment screw (outboard screw) located
on the back of the lamp assembly clockwise
or counterclockwise until the bubble in the
spirit level is centered when viewed from
directly above the bubble.
[SV40725(ALL)04/95]
3. Close the hood.
*
[SV40750(ALL)02/95]
If the vehicle is on a downward or upward
slope of not more than1.2Ê, theVHAD's bubble
level can be used to correct for the effects of the
surface slope, provided that the slope is
accurately known.
*
[SV40775(ALL)02/95]
Each graduation of the bubble level represents
0.19Ê ofdownward or upward slope. To correct
for the effects of a surface slope, turn the
vertical aim adjustment screw until the bubble is
centered at a position corresponding to the slope
of the surface.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

350 Index
Cleaning your vehicle (continued)
engine compartment.......... 263
exterior................ 7
headlamps.............. 108
instrument panel............ 91
mirrors................ 154
plastic parts.............. 8
polishing................ 7
rustproofing.............. 8
safety belts............... 23
tail lamps.............. 108
washing................ 7
wheels................ 296
windows............... 105
Clock.................. 114
Cold engine starting............ 65
Compact disc player (see Electronic sound
system)................ 181
Console, description........... 156
Coolant (see Engine coolant)
checking and adding......... 276
drain and flush............ 281
preparing for storage......... 334
refill capacities............ 281
specifications............. 331
temperature gauge........... 84
Cooling fan............... 256
Cruise control (see Speed control)..... 120
Cupholder(s).............. 157
Customer Assistance Center,
Ford (U.S.).............. 238
Customer Assistance Centre,
Ford of Canada............ 238
D
Daytime running light system...... 107
Defrost
rear window and side view mirrors. . . 104
windshield............ 95,102
Dispute Settlement Board........ 239
File:fcixs.ex
Update:Tue Aug 8 10:58:02 1995