ECU Mercury Sable 1996 s Owner's Guide

193
*
[DR04451(ALL)03/95]
RWARNING
If you need to shift out of P (Park)
by using the alternate procedure
described above, it is possible that a
fuse has blown and that your
brakelamps may also not be
functional. Please refer to the chapter
titledServicing Your Vehiclein this
Owner Guide for instructions on
checking and replacing fuses. DO
NOT DRIVE YOUR VEHICLE
UNTIL YOU VERIFY THAT THE
BRAKELAMPS ARE WORKING.
%*
[DR04501(ALL)11/94]
Using a column-mounted gearshift
*
[DR04550(ALL)04/95]
If your gearshift is on the column, you can use
any of the following positions:
[DR04601(ALL)11/94]
one third page art:0000491-E
The column-mounted gearshift
*
[DR04650(ALL)01/95]
Once you place the gearshift securely into
position, gradually release the brake pedal and
use the accelerator as necessary.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

195
*
[DR06100(ALL)04/95]
When to use 1 (First)
*
[DR06200(ALL)11/94]
Use 1 (First) when added engine braking is
desired when descending steep hills.
*
[DR06220(ALL)11/94]
The automatic transaxle will shift to the proper
gear to ascend any grade without any need to
shift to 1 (First).
[DR06300(ALL)04/95]
Do not go faster than 38 mph (61 km/h) in this
gear. You can upshift from 1 (First) to D (Drive)
or from 1 (First) toj(Overdrive) at any speed.
*
[DR06400(ALL)01/95]
P (Park)
*
[DR06500(ALL)11/94]
Always come to a complete stop before you shift
into P (Park). Make sure that the gearshift is
securely latched in P (Park). This locks the
transaxle and prevents the front wheels from
rotating.
*
[DR06600(ALL)01/95]
RWARNING
Do not use the P (Park) position in
place of the parking brake. Always
set the parking brake fully and make
sure that the gearshift is securely
latched in P (Park).
*
[DR06625(ALL)03/95]
Always turn off the ignition
whenever you leave your vehicle. Do
not leave your vehicle unattended
while the engine is running.
*
[DR06650(ALL)01/95]
If you do not take these precautions,
your vehicle may move unexpectedly
and injure someone.
[DR06700(ALL)11/94]
You can tell a column-mounted gearshift is
securely latched in P (Park) if you cannot move
it without pulling it toward you and rotating it
downward.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

199 [DR06789(ALL)04/95]
If your gearshift is on the console, you can use
any of the following positions:
[DR06790(ALL)04/95]
half page art:0001028-D
The console-mounted gearshift
*
[DR06791(ALL)04/95]
The console-mounted gearshift will lock when
you turn the key to the LOCK position. When
the gearshift is in any position except P (Park),
the ignition key cannot be turned to LOCK or
removed from the steering column. TO
REMOVE THE KEY, the gearshift levermustbe
in P (Park).
*
[DR06793(ALL)11/94]
Once the gearshift is secure in the desired
position, release the brake pedal and use the
accelerator as necessary.
*
[DR06795(ALL)01/95]
R (Reverse)
*
[DR06800(ALL)02/95]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

201 [DR08050(ALL)11/94]
NOTE: If the O/D OFF indicator light is
flashing on and off repeatedly when
the vehicle is started or does not come
on when the O/D OFF switch is
pushed, it means that there is a
transaxle electronic system malfunction.
You should contact your dealer as soon
as possible or damage to the transaxle
could occur.
*
[DR08075(ALL)02/95]
The transaxle will be in the ªoverdrive onº
mode when the vehicle is started even if the
O/D OFF mode was selected when the vehicle
was last shut off.
*
[DR09025(ALL)01/95]
When to use 2 (Second)
[DR09050(ALL)11/94]
Use Second for start-up on slippery roads or to
give you more engine braking to slow your
vehicle on downgrades.
*
[DR09075(ALL)04/95]
When to use 1 (First)
*
[DR10025(ALL)11/94]
Use 1 (First) when added engine braking is
desired when descending steep hills.
*
[DR10050(ALL)11/94]
The automatic transaxle will shift to the proper
gear to ascend any grade without any need to
shift to 1 (First).
[DR10075(ALL)11/94]
Do not go faster than 38 mph (61 km/h) in this
gear. You can upshift from 1 (First) to D
(Overdrive) at any speed.
*
[DR10125(ALL)01/95]
P (Park)
*
[DR10150(ALL)11/94]
Always come to a complete stop before you shift
into P (Park). Make sure that the gearshift is
securely latched in P (Park). This locks the
transaxle and prevents the front wheels from
rotating.
[DR10160(ALL)04/95]
If your vehicle has a console mounted gearshift,
the gearshift indicator in the cluster is
illuminated in P (Park) only when the gearshift
button is released.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

202
*
[DR10175(ALL)01/95]
RWARNING
Do not use the P (Park) position in
place of the parking brake. Always
set the parking brake fully and make
sure that the gearshift is securely
latched in P (Park).
*
[DR10225(ALL)03/95]
Always turn off the ignition
whenever you leave your vehicle. Do
not leave your vehicle unattended
while the engine is running.
*
[DR10250(ALL)01/95]
If you do not take these precautions,
your vehicle may move unexpectedly
and injure someone.
[DR10275(ALL)11/94]
You can tell a console-mounted gearshift is
securely latched in P (Park) if you cannot move
it without pushing in the thumb button.
*
[DR15600(ALL)01/95]
Steering Your Vehicle
%*
[DR15800(ALL)01/95]
Your vehicle comes with power steering. Power
steering uses energy from the engine to help
steer your vehicle.
[DR15970(ALL)11/94]
Your vehicle has variable-assist steering. This
system provides light power steering efforts for
parking and heavier power steering efforts for
highway driving. If you notice that the power
steering effort does not change according to the
speed you are traveling, or if the power steering
system is not working, have the system checked.
%*
[DR16100(ALL)04/95]
If the amount of effort needed to steer your
vehicle changes at a constant vehicle speed, have
the power steering system checked. If the power
steering system breaks down (or if the engine is
turned off), you can steer the vehicle manually
but it takes more effort.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

206 [DR18300(ALL)11/94]
one third page art:0001391-AThe parking brake and parking brake release
*
[DR18420(ALL)03/95]
RWARNING
Do not use the gearshift in place of
the parking brake. Always set the
parking brake fully and make sure
that the gearshift is securely latched
in P (Park).
*
[DR18700(ALL)01/95]
RWARNING
If the parking brake is fully released,
but the Brake Warning Light remains
on, have the brakes checked
immediately. They may not be
working properly.
*
[DR18750(ALL)01/95]
RWARNING
To avoid personal injury when
manually releasing the parking
brake, make sure the gearshift
selector is securely latched in P
(Park) and do not release the parking
brake from outside the vehicle.
File:fcdrs.ex
Update:Wed Dec 20 09:31:15 1995

227 [RE12000(ALL)11/94]
2. Remove the lug nuts by using a lug wrench.
Never loosen the hub nuts. See the picture
later in this section if you are not sure where
to find the lug nuts.
*
[RE12005(ALL)07/94]
RWARNING
Your vehicle has been built with
metric (12 mm) threads on the wheel
studs and lug nuts. Make certain,
during wheel removal, the same nuts
removed are reinstalled, or if
replaced, nuts with metric threads
and the same chamfer configuration
are used. Installation of an improper
thread nut on a metric stud will not
properly secure the wheel to the hub
and will damage the stud so that it
must be replaced. Damaged studs
may result in wheel separation and
personal injury.
*
[RE12100(ALL)01/95]
3. Replace the flat tire with the spare tire,
making sure that the air valve stem is facing
outward.
*
[RE12200(ALL)03/95]
4. Reinstall the lug nuts, tightening until the
wheel is snug against the hub. The beveled
edges on the lug nuts face inward. Do not
fully tighten the lug nuts until you lower the
vehicle. If you do, you could force the
vehicle off the jack.
*
[RE12300(ALL)02/95]
5. Lower the vehicle by turning the jack handle
counterclockwise.
*
[RE12400(ALL)01/95]
6. Remove the jack and fully tighten the lug
nuts in the order shown in the following
illustration. As soon as possible, have your
dealer or a qualified service technician check
the lug nuts for proper torque specifications.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

228 [RE12500(ALL)12/91]
one third page art:0000395-BThe lug nuts on the wheel
*
[RE12600(ALL)11/94]
7. Place any wheel covers and ornaments in the
trunk.
*
[RE12700(ALL)03/95]
8. Put the tire, jack, and wrench away. Make
sure the jack is securely fastened so it does
not rattle when you drive.
*
[RE12750(ALL)03/95]
9. Unblock the wheels.
[RE13007(ALL)04/95]
Removing and Replacing Wheel Covers
[RE13008(ALL)04/95]
Your vehicle may have wheel covers with a wire
retention system.
[RE13009(ALL)03/95]
To remove the wheel cover:
[RE13010(ALL)04/95]
Pry it loose by carefully inserting the tapered
end of the jack handle between the wheel cover
and the wheel.
[RE13011(ALL)04/95]
To replace the wheel cover:
[RE13012(ALL)04/95]
1. One of the windows on the wheel cover is
identified with a valve stem logo on the
back side of the cover. Install the wheel
cover to the wheel with the window at the
valve stem.
[RE13013(ALL)04/95]
2. Hold the wheel cover in this position and
press the cover onto the wheel with the
palm of your hand. Do not force or hammer
the cover.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

255
Servicing Your Sable
%*
[SV00300(ALL)03/95]
Service Made Easy
*
[SV00400(ALL)01/95]
Ford has two goals for servicing your vehicle.
*
[SV00500(ALL)01/95]
1. When we can, we design parts that do not
need to be serviced.
*
[SV00600(ALL)01/95]
2. We want to make servicing your vehicle as
easy as possible. To help you:
*
[SV00700(ALL)01/95]
q
We highlight do-it-yourself items in yellow in
the engine compartment so that you can find
them easily.
*
[SV00800(ALL)01/95]
q
When possible, we design parts Ð such as
the headlamp bulbs Ð that can be replaced
without tools.
*
[SV00900(ALL)05/94]
q
We give you a Maintenance Schedule that
makes tracking routine service for your
vehicle easy. The maintenance schedule is
located in theMaintenance Schedule and Record
booklet.
*
[SV01000(ALL)01/95]
This chapter tells you about the basic parts that
you need to check and service regularly.
*
[SV01100(ALL)03/95]
If your vehicle needs professional servicing, see
theCustomer Assistancechapter.
*
[SV01200(ALL)03/95]
Check yourWarranty Information Bookletto find
out which parts are covered.
*
[SV01250(ALL)03/95]
Ford Motor Company recommends that you
perform the Owner Maintenance Checks listed in
theMaintenance Schedule and Recordbooklet.
These services are important for the proper
operation of your vehicle. In addition to the
conditions listed in the Owner Maintenance
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

257
*
[SV01900(ALL)03/95]
q
If you must work with the engine running,
avoid wearing loose clothing or jewelry that
could get caught in moving parts. Take
appropriate precautions with long hair.
*
[SV02000(ALL)01/95]
q
Do not work on a vehicle in an enclosed
space with the engine running, unless you are
sure you have enough ventilation.
*
[SV02100(ALL)01/95]
q
Never get under a vehicle while it is
supported by a jack only. If you must work
under a vehicle, use safety stands.
*
[SV02200(ALL)01/95]
q
Keep all lit cigarettes and other smoking
materials away from the battery and all
fuel-related parts.
*
[SV02250(ALL)03/95]
If you disconnect the battery, the engine must
ªrelearnº its idle conditions before your vehicle
will drive properly. To find out how the engine
does this, seeBatteryin this chapter.
*
[SV02550(ALL)03/95]
Working with the engine off:
*
[SV02600(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02625(ALL)03/95]
2. Remove the key from the ignition after you
turn the engine off.
*
[SV02650(ALL)03/95]
3. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
*
[SV02700(ALL)03/95]
Working with the engine on:
*
[SV02800(ALL)03/95]
1. Set the parking brake fully and make sure
that the gearshift is securely latched in P
(Park).
*
[SV02825(ALL)03/95]
2. Block the wheels. This will prevent your
vehicle from moving unexpectedly.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995