instrument panel Mercury Sable 1996 s Owner's Guide

94 [IP03300(ALL)03/95]Function selector knob
[IP03351(ALL)04/95]
The function selector knob controls airflow to
the inside of the vehicle.
[IP03401(ALL)03/95]
MAX A/C
[IP03450(ALL)03/95]
MAX A/C uses recirculated air to cool the
vehicle. It allows for faster cooling but is noisier
than A/C. The airflow will be from the
instrument panel registers.
[IP03501(ALL)03/95]
A/C
[IP03550(ALL)04/95]
A/C uses outside air to cool the vehicle. It is
quieter that MAX A/C, but not as economical.
The airflow will be from the instrument panel
registers.
[IP03601(ALL)03/95]
VENT
[IP03650(ALL)03/95]
VENT brings in outside air through the
instrument panel registers. It can be used for
heating or ventilating.
[IP03701(ALL)03/95]
OFF
[IP03750(ALL)03/95]
In OFF, outside air is shut out and the fan will
not operate.
[IP03801(ALL)04/95]
S(Panel and floor)
[IP03850(ALL)04/95]
This brings in outside air through the instrument
panel registers and the front and rear floor
ducts. It can be used for heating or ventilating.
[IP03901(ALL)04/95]
R(Floor)
[IP03950(ALL)04/95]
This allows for maximum heating. The airflow is
from the front and rear floor ducts.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

95 [IP04001(ALL)04/95]
P(Floor and defrost)
[IP04050(ALL)04/95]
This brings in outside air through the floor ducts
and the windshield defroster ducts. It can be
used for heating or ventilation.
[IP04100(ALL)04/95]
V(Defrost)
[IP04150(ALL)04/95]
This brings in outside air through the
windshield defroster ducts. It can be used to
clear ice or fog from the windshield.
[IP04200(ALL)03/95]
Temperature control knob
[IP04250(ALL)03/95]
The temperature control knob may be adjusted
from cool (blue range) to warm (red range).
%*
[IP04700(ALL)04/95]
Electronic Automatic Temperature Control
System
*
[IP04725(ALL)02/95]
The control for your Electronic Automatic
Temperature Control (EATC) is located at the
center of the instrument panel in the Integrated
Control Panel and will operate only when the
ignition is turned on to the ON position.
*
[IP04825(ALL)02/95]
The EATC feature will maintain the temperature
you select and automatically control the airflow
for your comfort. It also allows you to override
the automatic operation with manual override
buttons.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

101
*
[IP07225(ALL)01/95]
Manual override buttons
[IP07325(ALL)04/95]
Your EATC has six buttons which allow you to
make special selections. The buttons are located
along the bottom edge of the EATC and allow
you to determine where the air will be
discharged. Pressing any override button
changes the air discharge location only. It does
not affect the ability of the system to control
temperature or the fan speed. Return to fully
automatic operation by pushing the AUTO
button.
*
[IP07425(ALL)01/95]
MAX A/C button
[IP07525(ALL)04/95]
The MAX A/C feature allows for faster cooling
because air is drawn from inside the vehicle.
Using inside air causes the fan to sound louder
which is normal for this selection. The display
window will change to indicate MAX A/C and
the airflow will be from the instrument panel
registers. To exit, push AUTO or any of the
other five manual override buttons.
%*
[IP07625(ALL)01/95]
VENT button
[IP07725(ALL)03/95]
Press this button to select outside air through
the instrument panel registers. The display
window will show the set temperature and
VENT to the lower right of the temperature.
Your EATC will heat the air if the temperature
you have selected is warmer than the outside air
coming into the vehicle. However, the air will
NOT be cooled regardless of the temperature
setting. Airflow will be from the instrument
panel registers.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

102 [IP07825(ALL)04/95]S(Panel and floor) button
[IP07925(ALL)02/95]
Push this button to get air from the floor and
instrument panel registers at the same time. The
display will show the set temperature andS.
Depending on the selected temperature, the air
will be automatically heated or cooled.
[IP08025(ALL)04/95]
R(Floor)
[IP08125(ALL)03/95]
Airflow will be to the floor when theR(floor)
button is pressed. The display window will
show the set temperature andR(floor) to the
right of the temperature. Fan speed will be
automatic unless manually controlled. If you
override the fan speed and wish to return to
automatic fan control, press AUTO. Then, again
selectR(floor) for airflow to the floor.
[IP08225(ALL)04/95]
P(Floor and defrost)
[IP08325(ALL)02/95]
Press this button to get air to the floor and
windshield defrosters at the same time. The
display will show the set temperature andP.If
the outside temperature is about50ÊF (10ÊC) and
above, the air will be dehumidified to remove
moisture. This will help to prevent fogging in
humid weather.
[IP08425(ALL)04/95]
VF-DEF (Front defrost)
[IP08525(ALL)02/95]
Press theVF-DEF (front defrost) button to
obtain maximum airflow to the windshield.
Adjust the temperature setting as required for
defrosting. The Display window will show the
temperature setting withVto the right of the
temperature. When the outside temperature is
about50ÊF (10ÊC) andabove, the air will be
dehumidified to remove moisture. This will help
prevent fogging in humid weather.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

104
*
[IP09325(ALL)03/95]
q
Do not put objects under the front seats that
interfere with the flow of air to the back seat
area.
[IP09425(ALL)04/95]
q
Remove any snow, ice, or leaves from the air
intake area of your climate control system
which could block the air intake. The intake
area is located at the bottom of the
windshield, under the hood at the passenger
side rear corner.
[IP09500(ALL)03/95]
q
If the air conditioner performs well in MAX
A/C but not in A/C, this may indicate that
the MicronAirHfilter (if equipped) needs to
be replaced.
[IP10000(ALL)03/95]
MicronAirHAir Filter (If equipped)
*
[IP10100(ALL)02/95]
Your vehicle may have an air filter that removes
pollen and road dust from outside air before it
is directed to the interior of the vehicle. For
maintenance of this filter, seeServicing Your
Sable.
[IP21650(ALL)04/95]
Rear Window Defroster and Heated Side
View Mirrors
[IP21700(ALL)04/95]
The defroster for the rear window clears frost,
fog, or thin ice from both the inside and outside
of the rear window and activates the heated side
view mirrors.
[IP21900(ALL)04/95]
The button for the rear defroster and heated side
view mirrors is on the instrument panel.
[IP22200(ALL)04/95]
one inch art:0000651-E
The button that controls the rear window defroster and
heated side view mirrors
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

107 [IP25250(ALL)02/89]
To change your headlamps from low to high
beam, push the turn signal lever away from you.
To change them back to low beam, pull the
lever toward you.
*
[IP25300(ALL)03/93]
For more information about how the high beam
headlamps work, seeSteering column controlsin
the Index.
%*
[IP25605(ALL)01/95]
Daytime Running Light System
[IP25610(ALL)03/95]
(Canadian and fleet vehicles only)
*
[IP25615(ALL)03/95]
The Daytime Running Light (DRL) system is
designed to turn the high beam headlamps on,
with a reduced light output and without
illuminating the high beam indicator lamp in the
instrument panel. The DRL system operates
when all of the following conditions are met:
*
[IP25620(ALL)03/95]
q
The vehicle is ªrunning.º
*
[IP25625(ALL)01/95]
q
The vehicle has a fully released parking
brake.
*
[IP25630(ALL)03/95]
q
The headlamp system is in the OFF position.
*
[IP25635(ALL)01/95]
NOTE: If you have a vehicle with an
automatic lighting system, the DRL
system is active until the automatic
system turns on the headlamps.
*
[IP25636(ALL)10/94]
NOTE: The high beam indicator will not turn
on in the flash-to-pass mode during
nighttime driving.
[IP25637(ALL)01/95]
You may notice that the lights flicker when the
vehicle is turned on or off. This is a normal
condition.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

109 [IP27100(ALL)02/95]
one third page art:0000693-C
The autolamp system on the left side of the instrument
panel
*
[IP27400(ALL)01/95]
To set the autolamp:
*
[IP27450(ALL)08/95]
1. Make sure the headlamp knob is in the OFF
position. If the switch for the headlamps is
ON, you cancel the autolamp.
*
[IP27550(ALL)01/95]
2. Turn the ignition key to ON or start your
vehicle.
*
[IP27650(ALL)01/95]
3. Find the autolamp thumbwheel to the left of
the steering wheel on the instrument panel.
[IP27750(ALL)02/95]
4. Turn the autolamp thumbwheel past the stop
to the beginning of the MAX position. The
indicator light will come on.
*
[IP27850(ALL)01/95]
5. The autolamp automatically turns the lamps
on and off for you.
[IP27950(ALL)08/95]
Do not put any articles on top of the photocell
that is located in the top right corner of the
instrument panel. This photocell controls the
autolamp. If you cover it, the photocell reacts as
if it is nighttime, and the lamps turn on.
*
[IP28050(ALL)01/95]
To turn the autolamp off, move the thumbwheel
back to OFF.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

110
*
[IP28500(ALL)01/95]
You can set the autolamp so the headlamps stay
on for up to three minutes after you turn your
vehicle off.
*
[IP28600(ALL)01/95]
To keep the lamps on after you leave your
vehicle:
*
[IP28650(ALL)01/95]
q
Turn the thumbwheel as far into the MAX
range as you want.
*
[IP28750(ALL)01/95]
q
The further you move the thumbwheel into
the DELAY area (toward the MAX position),
the longer the lamps will stay on after you
leave your vehicle. Similarly, if you move the
thumbwheel only slightly into the DELAY
area, your lamps will stay on only for a
moment after you turn your vehicle off.
%*
[IP29800(ALL)01/95]
Lighting Up the Interior and Instrument
Panel
*
[IP30000(ALL)08/95]
With the light knob in the parking lamps or the
headlamps position, you can brighten or dim the
lights in the instrument panel. To do this, use
the thumbwheel to the left of the steering wheel.
This wheel also turns on the interior lights with
the light switch on or off.
[IP30300(ALL)02/95]
one third page art:0000692-C
The thumbwheel that controls the light on the instrument
panel
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

111 [IP30700(ALL)11/94]
To dim the instrument panel lights, rotate the
thumbwheel down. To turn on the interior
lights, turn the thumbwheel all the way up. The
interior lights also come on when any side door
or the liftgate is opened.
[IP30925(ALL)03/95]
Dome Lamps
[IP30950(ALL)03/95]
The front dome lamp is located overhead
between the driver and front passenger seats.
However, if your vehicle is equipped with a
power moon roof, the dome lamp is located
behind the moon roof.
[IP30975(ALL)11/94]
In the wagon, the rear dome lamp is located
overhead near the rear seating positions.
[IP31025(ALL)02/95]
one third page art:0001410-A
The dome/map lamp
[IP31050(ALL)03/95]
Turn the map lamps on and off with the
switches on the lamp. The dome lamp
illuminates when any door is opened. If either
the driver's or passenger's front door is opened
using the outside door handle, the light will
remain on for 25 seconds after the door has been
shut. If any other door is opened or if either of
the front doors is opened using the inside
handle, the lamp will immediately turn off when
the door is closed.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

115
Steering Column Controls
*
[SC00400(ALL)01/95]
The controls on the steering column and wheel
are designed to give you easy access to the
controls while you are driving.
%
*
[SC00500(ALL)01/95]
The Turn Signal Lever
*
[SC00600(ALL)01/95]
You can use the turn signal lever on the left side
of the steering column to:
[SC00700(ALL)03/95]
q
operate the turn signals
*
[SC00800(ALL)01/95]
q
turn the high beams on/off
*
[SC00900(ALL)01/95]
q
flash the lights
*
[SC01000(ALL)01/95]
q
turn the windshield wipers and washer
on/off
%*
[SC01100(ALL)01/95]
Turn Signals
*
[SC02201(ALL)03/95]
Move the lever up to signal a right turn. Move
it down to signal a left turn. The corresponding
indicator light in the instrument cluster will
flash.
*
[SC02401(ALL)03/95]
If the turn signal stays on after you turn, move
the lever back to the center (off) position.
*
[SC02451(ALL)03/95]
For lane changes, move the lever far enough to
signal but not to latch. The lever will return to
the off position when you release it.
%*
[SC02800(ALL)03/95]
High Beams
*
[SC03100(ALL)08/95]
To turn on the high beams, turn the headlamp
control knob to the headlamp ON position and
push the turn signal lever away from you until
it latches. When the high beams are ON, the
high beam indicator light on the instrument
panel comes on.
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995