battery Mercury Sable 1996 Owner's Manuals

97 [IP05025(ALL)03/95]
To turn your EATC on, press the AUTO button
or any of the six manual override buttons along
the bottom of the control.
[IP05125(ALL)03/95]
To turn your EATC off, press the OFF button.
When the system is off, the Display window will
be blank (dark).
[IP05225(ALL)02/95]
If you select AUTO, the system will
automatically determine fan speed and airflow
location. If a manual override button is selected,
your selection determines airflow location only.
Fan speed remains automatic unless you
override it by pressing either side of the FAN
speed button located at the extreme left of the
control panel.
[IP05325(ALL)03/95]
To change the temperature, select any
temperature between65ÊF (18ÊC) and 85ÊF (29ÊC)
by pressing the
aor
bside of the TEMP
button. The EATC will display the selected
temperature.
[IP05400(ALL)04/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
[IP05425(ALL)03/95]
If you want continuous maximum cooling, press
the
bside of the TEMP button until60ÊF (16ÊC)
is shown in the display window. Your EATC
will cool at maximum and disregard the60ÊF
(16ÊC) setting until you select a warmer
temperature with the
aside of the TEMP
button. If you want continuous maximum
heating, press the
aside of the TEMP button
until90ÊF (32ÊC) isshown in the display
window. Your EATC will provide maximum
heat regardless of the90ÊF (32ÊC)setting until
you select a cooler temperature with the
bside
of the TEMP button.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

113 [IP31200(ALL)04/95]
Cleaning the Interior Lamps
*
[IP31300(ALL)04/95]
Your interior dome lamps and map lamps are
plastic and should be cleaned with a mild
detergent diluted in water. Rinse them with clear
water.
%*
[IP31400(ALL)01/95]
Battery Saver
[IP31500(ALL)11/94]
When the ignition is turned off, the vehicle will
turn off battery voltage to the interior lights
after 40 minutes.
*
[IP31600(ALL)02/95]
This will prevent draining of the battery if those
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the outside
front door handles are lifted, the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened,
or the ignition key is turned to the ON position.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

76 [LG03300(ALL)02/95]
one inch art:0000108-DBrake system warning light
*
[LG03500(ALL)01/95]
This light comes on when the parking brake is
set, or if it is not set, it comes on briefly when
you turn the ignition to the START position. It
normally goes off shortly after the engine starts
and you release the parking brake. If the light
stays on after you have fully released the
parking brake, have the hydraulic brake system
serviced by your dealer or a qualified service
technician.
*
[LG03700(ALL)01/95]
RWARNING
The BRAKE light indicates that the
brakes may not be working properly.
Have the brakes checked
immediately. Brake failure may result
in serious personal injury or vehicle
damage.
%*
[LG03800(ALL)01/95]
Charging System Light
*
[LG03900(ALL)03/95]
This light, shown as a battery symbol on your
cluster, indicates that your battery is not being
charged and that you need to have the electrical
system checked.
File:fclgs.ex
Update:Tue Aug 8 11:08:13 1995

97 [IP05025(ALL)03/95]
To turn your EATC on, press the AUTO button
or any of the six manual override buttons along
the bottom of the control.
[IP05125(ALL)03/95]
To turn your EATC off, press the OFF button.
When the system is off, the Display window will
be blank (dark).
[IP05225(ALL)02/95]
If you select AUTO, the system will
automatically determine fan speed and airflow
location. If a manual override button is selected,
your selection determines airflow location only.
Fan speed remains automatic unless you
override it by pressing either side of the FAN
speed button located at the extreme left of the
control panel.
[IP05325(ALL)03/95]
To change the temperature, select any
temperature between65ÊF (18ÊC) and 85ÊF (29ÊC)
by pressing the
aor
bside of the TEMP
button. The EATC will display the selected
temperature.
[IP05400(ALL)04/95]
To change the temperature display from
Farenheit to Celsius, depress the MAX A/C and
VF-DEF at the same time and hold them
down for about a second. To change back to the
original setting, repeat the process. If the battery
is disconnected, the display will revert to
Fahrenheit and must be reset to Celsius.
[IP05425(ALL)03/95]
If you want continuous maximum cooling, press
the
bside of the TEMP button until60ÊF (16ÊC)
is shown in the display window. Your EATC
will cool at maximum and disregard the60ÊF
(16ÊC) setting until you select a warmer
temperature with the
aside of the TEMP
button. If you want continuous maximum
heating, press the
aside of the TEMP button
until90ÊF (32ÊC) isshown in the display
window. Your EATC will provide maximum
heat regardless of the90ÊF (32ÊC)setting until
you select a cooler temperature with the
bside
of the TEMP button.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

113 [IP31200(ALL)04/95]
Cleaning the Interior Lamps
*
[IP31300(ALL)04/95]
Your interior dome lamps and map lamps are
plastic and should be cleaned with a mild
detergent diluted in water. Rinse them with clear
water.
%*
[IP31400(ALL)01/95]
Battery Saver
[IP31500(ALL)11/94]
When the ignition is turned off, the vehicle will
turn off battery voltage to the interior lights
after 40 minutes.
*
[IP31600(ALL)02/95]
This will prevent draining of the battery if those
lights have been left on inadvertently or if a
door is not completely closed. Battery voltage to
these lamps will be restored when the outside
front door handles are lifted, the keyless entry
keypad is used, the remote entry transmitter is
used, any door is opened, the trunk is opened,
or the ignition key is turned to the ON position.
File:fcips.ex
Update:Wed Dec 20 09:32:19 1995

119
*
[SC05560(ALL)03/95]
The hazard flasher serves as a warning to other
drivers to be careful when approaching or
passing your vehicle.
*
[SC05590(ALL)03/95]
The flashers work whether your vehicle is
running or not. The flashers work for up to two
hours when the battery is fully charged and in
good condition without draining the battery
excessively. If the flashers run for longer than
two hours or if the battery is not fully charged,
the battery can be drained.
%
*
[SC05600(ALL)01/95]
Horn
*
[SC05800(ALL)04/95]
To sound the horn, push the center pad area of
the steering wheel.
[SC06000(ALL)02/95]
one third page art:0001403-B
The horn on the steering wheel
File:fcscs.ex
Update:Tue Aug 8 11:05:58 1995

217
Roadside Emergencies
%*
[RE00310(ALL)03/95]
If Your Vehicle Needs a
Jump-Start
*
[RE00320(ALL)01/95]
Your vehicle's battery may die if you leave the
lights on or any electrical equipment on after
you turn the engine off. If this happens, you
may be able to jump-start from a booster battery
to start your vehicle.
*
[RE00400(ALL)01/95]
RWARNING
Flames, sparks, or lit cigarettes can
cause the gases around the battery to
explode, causing injury and damage.
Keep these things away from the
battery.
*
[RE00500(ALL)01/95]
To protect yourself when charging a
battery, always shield your face and
eyes. Make sure that you can breathe
fresh air.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

218 %
*
[RE00700(ALL)03/95]
RWARNING
Be careful when lifting a battery that
is in a plastic case. If you put too
much pressure on the ends, you
could spill acid from the vent caps,
causing serious damage to the vehicle
and injury to yourself. Lift the
battery with a carrier or with your
hands on the opposite corners.
%*
[RE00800(ALL)01/95]
Do not let children touch the battery.
Batteries contain sulfuric acid which
burns skin, eyes, and clothing. If the
acid touches someone's skin, eyes, or
clothing, immediately flush the area
with water for at least 15 minutes. If
someone swallows the acid, have him
or her drink lots of milk or water
first, then Milk of Magnesia, a
beaten egg, or vegetable oil. Call a
doctor immediately.
*
[RE00900(ALL)03/95]
To avoid damaging your vehicle or your battery,
and to avoid injury to yourself, follow these
directions for preparing your vehicle to
jump-start and connecting the jumper cables in
the order they are given. If in doubt, call for
road service.
*
[RE01000(ALL)03/95]
Preparing Your Vehicle
*
[RE01100(ALL)03/95]
1. Your vehicle has a 12-volt starting system, so
you need to use a 12-volt jumper system.
You will damage your starting motor,
ignition system, and other electrical parts if
you connect them to a 24-volt power supply
(either two 12-volt batteries in series or a
24-volt generator set).
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

219
*
[RE01200(ALL)03/95]
2. Do not disconnect the battery of the disabled
vehicle. You could damage the vehicle's
electrical system.
*
[RE01300(ALL)04/95]
3. Park the booster vehicle close to the hood of
the disabled vehicle.Make sure the vehicles
do not touch each other.Set the parking
brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01400(ALL)03/95]
4. Check all battery terminals and remove any
excessive corrosion before you attach the
jumper cables.
[RE01500(ALL)04/95]
5. Turn on the heater fan in both vehicles. If
you have electronic climate control, press the
VF-DEF button. Turn off all other switches
and lights.
%*
[RE01700(ALL)08/95]
Connecting the jumper cables
*
[RE02500(ALL)03/95]
1. Connect one end of the first jumper cable to
the positive (+) terminal of the discharged
battery. (You can connect either jumper cable
to the positive (+) terminal, as long as you
use the same cable for both positive
terminals.) Most jumper cables have a red
cable and a black cable. The red cable is
generally used for the positive terminals and
the black for the negative ones.
*
[RE02600(ALL)04/95]
2. Connect the other end of the first cable to
the positive (+) terminal of the booster
battery.
*
[RE02700(ALL)03/95]
3. Connect one end of the second cable to the
negative (s) terminal of the booster battery
Ð NOT to the discharged battery.
*
[RE02800(ALL)04/95]
4. Connect the other end of the second cable to
a good metallic surface on the engine or
frame of the disabled vehicle.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995

220
*
[RE02900(ALL)03/95]
RWARNING
Do not connect the end of the second
cable to the negative (s) terminal of
the discharged battery. If you do, a
spark may cause an explosion of the
gases that normally surround the
battery and could seriously injure
someone.
[RE03100(ALL)04/95]
one third page art:0000388-D
Jumper cable connections
*
[RE03400(ALL)03/95]
Jump-Starting
*
[RE03600(ALL)03/95]
1. Make sure that the jumper cables are not in
the way of moving engine parts, then start
the booster vehicle. Run the engine at a
moderate speed.
*
[RE03700(ALL)03/95]
2. Let the discharged battery charge for a few
minutes and then start the disabled vehicle.
It may take a couple of tries before the
vehicle starts. If the vehicle does not start
after several attempts, there may be a
different problem.
*
[RE03800(ALL)03/95]
3. When both vehicles are running, let them
idle for a few minutes to charge the
discharged battery.
File:fcres.ex
Update:Tue Aug 8 11:02:29 1995