open hood Mercury Sable 1996 Owner's Manuals

258
*
[SV03000(ALL)02/95]
RWARNING
Do not start your engine with the air
cleaner removed and do not remove
it while the engine is running.
%*
[SV03100(ALL)03/95]
Opening the Hood
%*
[SV03200(ALL)01/95]
1. Inside the vehicle, pull the hood release
handle located under the bottom left corner
of the instrument panel.
%*
[SV03300(ALL)02/95]
2. Go to the front of the vehicle and release the
auxiliary latch that is located under the hood
at the center of the vehicle.
*
[SV03400(ALL)01/95]
3. Lift the hood until the lift cylinders hold it
open.
*
[SV03500(ALL)01/95]
Whenever you close the hood, latch it securely.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

260
*
[SV04350(ALL)01/95]
NOTE: Read and understandPrecautions When
Servicing Your Vehicleat the beginning
of this chapter before opening the
hood.
%
*
[SV04500(ALL)04/95]
Engine Compartment
*
[SV04600(ALL)09/93]
Your vehicle has one of these types of engines:
[SV04700(ALL)08/95]
q
a 3.0L Vulcan engine
[SV04750(ALL)08/95]
q
a 3.0L Duratec engine
*
[SV04850(ALL)11/94]
The following pages show diagrams of each
engine type and where to find items that you
should regularly service.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

274 %
*
[SV13775(ALL)01/95]
Checking and Adding Engine Oil
*
[SV13800(ALL)03/95]
Since the proper amount of engine oil is
important for safe engine operation, check the oil
using the dipstick each time you put fuel in
your vehicle. Remember the engine must be off,
the oil must be warm and the vehicle must be
parked on level ground.
%*
[SV13900(ALL)04/95]
Checking the engine oil level:
*
[SV14000(ALL)02/95]
1. Turn the engine off after it has warmed up
and allow a few minutes for the engine oil
to drain back into the oil pan.
*
[SV14025(ALL)03/95]
2. Set the parking brake, making sure the
gearshift is securely latched in P (Park).
*
[SV14100(ALL)02/95]
3. Open the hood. Protect yourself from engine
heat.
*
[SV14200(ALL)03/95]
4. Locate the engine oil dipstick (highlighted in
yellow) and carefully pull it out of the
engine.
*
[SV14300(ALL)01/95]
5. Wipe the dipstick clean and put it back into
position, making sure it is fully seated.
[SV14400(ALL)02/95]
one inch art:0001397-A
Engine oil dipstick (3.0L Vulcan)
[SV14475(ALL)08/95]
one inch art:0001398-B
Engine oil dipstick (3.0L Duratec)
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

286
[SV23716(ALL)04/95]
MicronAirHAir Filter
Replacement
*
[SV23719(ALL)04/95]
In your climate control system, you may have a
filter that cleans the air before it enters the
interior of the vehicle. This filter should be
replaced at the intervals in theMaintenance
Schedule and Recordbooklet.
[SV23723(ALL)04/95]
To replace the MicronAirHair filter:
[SV23725(ALL)04/95]
1. Open the hood. Move the vacuum hose at
the rear passenger side of the engine
compartment by pulling the hose clips off
the leaf screen and removing the loose clip.
With a coin or screwdriver, turn the four
retainers on the leaf screen 90Ê and pull
them straight out. Remove the leaf screen.
[SV23730(ALL)04/95]
one third page art:0001387-A
Removing the vacuum hose clips
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995

319
*
[SV40201(ALL)02/95]
Horizontal aim adjustment
[SV40250(ALL)04/95]
1. Open the hood and locate the horizontal
indicator and adjusting screw.
*
[SV40375(ST)04/95]
2. Use a 4mm wrench to turn the horizontal
adjusting screw until the reference mark on
the reflector extension aligns with the ª0º
reference mark on the horizontal indicator
when viewed from directly above. If the
vehicle has been in an accident requiring the
front end of the vehicle to be repaired, the
horizontal indicator should be recalibrated
by a servicing facility using theTaurus/Sable
Service Manualinstructions.
*
[SV40501(ALL)02/95]
Vertical aim adjustment
*
[SV40601(ALL)02/95]
1. With the hood open, locate the bubble level
vertical aim indicator. It is visible when
viewed from above and to the rear of the
headlamp.
*
[SV40650(ALL)02/95]
2. With the vehicle on a level surface, use a
4mm wrench to turn the vertical aim
adjustment screw (outboard screw) located
on the back of the lamp assembly clockwise
or counterclockwise until the bubble in the
spirit level is centered when viewed from
directly above the bubble.
[SV40725(ALL)04/95]
3. Close the hood.
*
[SV40750(ALL)02/95]
If the vehicle is on a downward or upward
slope of not more than1.2Ê, theVHAD's bubble
level can be used to correct for the effects of the
surface slope, provided that the slope is
accurately known.
*
[SV40775(ALL)02/95]
Each graduation of the bubble level represents
0.19Ê ofdownward or upward slope. To correct
for the effects of a surface slope, turn the
vertical aim adjustment screw until the bubble is
centered at a position corresponding to the slope
of the surface.
File:fcsvs.ex
Update:Wed Dec 20 09:36:55 1995