battery Mercury Villager 1996 Owner's Manuals
[x] Cancel search | Manufacturer: MERCURY, Model Year: 1996, Model line: Villager, Model: Mercury Villager 1996Pages: 396, PDF Size: 3.67 MB
Page 74 of 396
Warning Lights and Gauges
73
*
[LG02700(ALL)01/95]
Charging System Light
*
[LG02800(ALL)03/95]
This light, shown as a battery symbol on your cluster, indicates
that your battery is not being charged and that you need to
have the electrical system checked.
[LG02900(ALL)09/93]
6 pica art:0040054-A
Charging system light
[LG03000(ALL)01/93]
This light comes on every time you turn your ignition key to
the ON or START position. The light should go off when the
engine starts and the alternator begins to charge.
*
[LG03100(ALL)01/95]
If the light stays on or comes on when the engine is running,
have the electrical system checked as soon as possible.
%*
[LG03200(ALL)02/95]
Engine Oil Pressure Warning Light
[LG03300(ALL)04/94]
The oil pressure light is represented by an oil can symbol. It
indicates the engine's oil pressure, not oil level. However, if
your engine's oil level is low, it could affect the oil pressure.
The oil can symbol will flash if the oil pressure drops below the
normal operating level. When you turn the key to the ON
position, the light will illuminate.
[LG03400(ALL)09/93]
6 pica art:0040060-A
Oil pressure light
File:05vxlgn.ex
Update:Tue Jun 4 11:35:19 1996
Page 112 of 396
112
[IP11000(ALL)04/95]
To activate the rear washer, press the RR WASH switch. For a
constant spray, hold the switch for a few seconds. For less
washer fluid, press the switch once and release it. When you
activate the washer, the wiper will cycle twice and then stop.
*
[IP11050(ALL)04/95]
Do not activate the washer for longer than fifteen seconds
continuously. This could damage the washer pump system.
*
[IP11100(ALL)04/95]
Hazard Flasher Switch
*
[IP11150(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[IP11200(ALL)09/93]
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these
lamps will flash on and off. The turn signal indicators cannot be
used when the hazard lamps are flashing. Operation of the
hazard flashers does not affect operation of the brakelamps.
*
[IP11300(ALL)12/93]
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the battery
excessively. If the flashers run for longer than two hours or if
your battery is not fully charged, your battery may be drained
to the point where the vehicle will not start.
[IP11400(ALL)01/93]
The hazard flasher switch is located on the instrument panel to
the right of the instrument cluster.
*
[IP11500(ALL)09/93]
To use the hazard flasher:
*
[IP11600(ALL)02/94]1.
Push the HAZARD switch; you will see the turn signal
arrows flash.
*
[IP11700(ALL)09/93]2.
To stop the hazard flashers, push the HAZARD switch again.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996
Page 119 of 396
Instrument Panel Controls
119
[IP15700(ALL)09/93]
10-1/2 pica
art:0040075-D
The dome lamp switch positions
[IP15800(ALL)07/93]
Either dome lamp will stay illuminated if the switch is pushed
to the ON position. The dome lamps will stay off if the switch
is pushed to the OFF position. When the switch is positioned to
the door/middle position, the dome lamps will come on when
either of the front doors or the sliding door is opened. The front
dome lamp, footwell lamps, and the sliding door step lamp
have a time delay feature and will gradually dim within about
15 seconds.
[IP15900(ALL)03/95]
The rear dome lamp also illuminates when the liftgate is opened
and goes off when it is closed. However, the rear dome lamp
will not remain lit in the ON position unless the ignition switch
is in the ON position. This feature is intended to help avoid a
run-down battery which can occur when a light is left on
unintentionally.
[IP15950(ALL)02/95]
If the vehicle doors are not fully closed and the interior lamps
remain illuminated, they will eventually turn off automatically
to prevent the battery from becoming discharged. Lamps that
illuminate when the front doors and the sliding door are open
will turn off after approximately 30 minutes. Lamps that are
illuminated when the liftgate is open will turn off after
approximately 60 minutes.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996
Page 141 of 396
Features
143
[FV05800(ALL)01/93]
The following numbers cannot be entered as a personal code:
[FV05900(ALL)01/93]
n
Any number containing digits that are all on the same
button. Example: 2-1-2-1-2
[FV06000(ALL)01/93]
n
Any number requiring sequential operation of the buttons.
Example: 1-3-5-7-0 or 7-5-3-1-9
[FV06100(ALL)04/95]
n
Any number with fewer than five digits or more than five
digits.
%*
[FV06200(ALL)02/95]
Programming your Personal Code
*
[FV06300(ALL)02/95]
To program your own code:
[FV06400(ALL)01/93]1.
Enter the permanent code.
[FV06500(ALL)04/95]2.
A buzzer will sound for about six seconds or until your
five-digit personal code is entered.
[FV06600(ALL)01/93]3.
If you have programmed a valid number within five seconds
of entering the permanent code, the buzzer will sound for
about two seconds and the keypad light will shut off.
[FV06700(ALL)04/95]4.
Test your personal code to see if it has properly registered. If
it registered, any previously entered personal code has been
erased from memory.
[FV06800(ALL)04/95]5.
If you have successfully entered your personal code, the
driver's door will unlock.
[FV06900(ALL)02/94]
If the personal code you entered did not work, it may be that
you entered an invalid personal code. SeeValid and Invalid Codes
in the previous section to select a valid personal code.
[FV07000(ALL)01/93]
NOTE: If the battery is ever disconnected, the permanent
code and your personal code will be retained in
memory.
File:08vxfvn.ex
Update:Mon Jun 3 14:49:33 1996
Page 145 of 396
Features
147
[FV08140(ALL)06/95]
If the batteries are removed for any reason other than
replacement, repeat the steps inReplacing the batteriesto test
your remote transmitter(s).
[FV08150(ALL)06/95]
n
An improperly disposed battery can hurt the environment.
Always confirm local regulations for battery disposal.
[FV08160(ALL)06/95]
n
The remote transmitter is waterproof; however, if it does get
wet, immediately wipe it completely dry.
[FV08170(ALL)06/95]
n
The operational range of the remote transmitter extends to
approximately 49 feet (15 meters) from the vehicle. This
range may vary with conditions.
*
[FV08175(ALL)06/95]
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
[FV08180(ALL)06/95]
Replacement/Additional Transmitters
[FV08190(ALL)07/95]
In the event a transmitter is lost or an additional remote
transmitter needs to be set, you must change the ID code.
Follow the steps below to change the ID code of your system,
or return the remaining transmitter(s) to your dealer for
reprogramming of your remote entry system. This is necessary
to prevent unauthorized use of the lost transmitter.
[FV08200(ALL)06/95]
ID Code Programming Procedure
[FV08210(ALL)06/95]
NOTE: All transmitters must be programmed (or
reprogrammed) at the same time. If the programming
mode is entered and the transmitters are not
programmed (or reprogrammed) at the same time, they
will not operate with the system.
[FV08220(ALL)06/95]1.
Enter vehicle and close and lock all doors.
File:08vxfvn.ex
Update:Mon Jun 3 14:49:33 1996
Page 208 of 396
212
*
[AS03400(ALL)06/95]2.
Press one of the memory preset buttons and hold the button
until the sound returns. That station is now held in memory
on that button.
*
[AS03500(ALL)06/95]3.
Follow the two steps above for each station memory preset
button you want to set.
[AS03550(ALL)06/95]
NOTE: If the vehicle's battery is disconnected, the Station
Memory Preset buttons will need to be reset.
[AS03600(ALL)06/95]
n
Using the Automatic Memory Store feature (Supersound
only)
[AS03900(ALL)06/95]
Activate Auto Memory Store by pushing the ªAUTO SETº
button once. Your radio will set the first six strong stations
of the band you are in (AM, FM1 or FM2) into the memory
buttons. The display will show ªAUTO,º then run through
the frequencies, stopping momentarily on the stations being
set into the memory buttons. The radio is now in the
ªAUTOº mode and this display will show ªAUTOº each
time a preset selected by ªAUTO SETº is activated.
*
[AS03950(ALL)06/95]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your
existing memory presets, which is especially handy while
traveling. Your radio will automatically set your memory
buttons to the strong local stations so you don't have to
continually manually tune to existing stations.
*
[AS04000(ALL)06/95]
NOTE: If there are fewer than six strong stations in the
frequency band, the remaining unfilled buttons will
store the last strong station detected on the band.
*
[AS04100(ALL)05/95]
After all stations have been filled, the radio will begin
playing the station stored on memory button 1.
[AS04200(ALL)06/95]
To deactivate the Auto Memory Store mode and return to
the manually-set memory button stations, simply push the
ªAUTO SETº button. Display will show ªAUTOº then
ªOFF.º
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996
Page 251 of 396
255
Roadside Emergencies
[RE00700(ALL)03/94]
Jump-Starting Your Battery
*
[RE00800(ALL)01/93]
Your vehicle's battery may discharge if you leave the lights or
any electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start from a booster battery
to start your vehicle.
*
[RE00900(ALL)02/95]
RWARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
*
[RE01000(ALL)02/95]
RWARNING
To protect yourself when charging a battery, always
shield your face and eyes. Make sure that you can
breathe fresh air.
%*
[RE01100(ALL)05/95]
RWARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
%*
[RE01200(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE01210(ALL)06/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996
Page 252 of 396
256
%*
[RE01300(ALL)05/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE01400(ALL)03/95]
To avoid damaging your vehicle or your battery, and to avoid
injury to yourself, follow these directions for preparing your
vehicle to jump-start and connecting the jumper cables in the
order they are given. If in doubt, call for road service.
*
[RE01500(ALL)03/95]
Preparing Your Vehicle
*
[RE01600(ALL)03/95]1.
Your vehicle has a 12-volt starting system, so you need to
use a 12-volt jumper system. You will damage your starting
motor, ignition system, and other electrical parts if you
connect them to a 24-volt power supply (either two 12-volt
batteries in series or a 24-volt generator set).
*
[RE01700(ALL)03/95]2.
Do not disconnect the battery of the disabled vehicle. You
could damage the vehicle's electrical system.
*
[RE01800(ALL)04/95]3.
Park the booster vehicle close to the hood of the disabled
vehicle.Make sure the vehicles do not touch each other.Set
the parking brake on both vehicles and stay clear of the
engine cooling fan and other moving parts.
*
[RE01900(ALL)03/95]4.
Check all battery terminals and remove any excessive
corrosion before you attach the jumper cables.
*
[RE02000(ALL)01/93]5.
Turn on the heater blower in both vehicles. Turn off all other
switches and lights in both vehicles to prevent possible
damage to either vehicle's electrical systems.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996
Page 253 of 396
Roadside Emergencies
257
%*
[RE02100(ALL)05/95]
Connecting the jumper cables
*
[RE02200(ALL)03/95]1.
Connect one end of the first jumper cable to the positive (+)
terminal of the discharged battery. (You can connect either
jumper cable to the positive (+) terminal, as long as you use
the same cable for both positive terminals.) Most jumper
cables have a red cable and a black cable. The red cable is
generally used for the positive terminals and the black for
the negative ones.
*
[RE02300(ALL)04/95]2.
Connect the other end of the first cable to the positive (+)
terminal of the booster battery.
*
[RE02400(ALL)05/95]3.
Connect one end of the second cable to the negative (s)
terminal of the booster battery Ð NOT to the discharged
battery.
*
[RE02500(ALL)04/95]4.
Connect the other end of the second cable to a good metallic
surface on the engine or frame of the disabled vehicle.
*
[RE02600(ALL)05/95]
RWARNING
Do not connect the end of the second cable to the
negative (-) terminal of the battery to be jumped. A spark
may cause an explosion of the gases that surround the
battery.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996
Page 255 of 396
Roadside Emergencies
259
*
[RE02800(ALL)03/95]
Jump-Starting
*
[RE02900(ALL)03/95]1.
Make sure that the jumper cables are not in the way of
moving engine parts, then start the booster vehicle. Run the
engine at a moderate speed.
*
[RE03000(ALL)03/95]2.
Let the discharged battery charge for a few minutes and then
start the disabled vehicle. It may take a couple of tries before
the vehicle starts. If the vehicle does not start after several
attempts, there may be a different problem.
*
[RE03100(ALL)03/95]3.
When both vehicles are running, let them idle for a few
minutes to charge the discharged battery.
*
[RE03200(ALL)03/95]
Removing jumper cables
*
[RE03300(ALL)03/95]1.
Always remove the jumper cables in the reverse order.
Remove the negative (s) end of the jumper cable from the
metallic surface on the engine or frame of the disabled
vehicle.
*
[RE03400(ALL)05/95]2.
Remove the negative (s) cable from the booster battery.
*
[RE03500(ALL)06/95]3.
Remove the positive (+) cable from the booster battery.
*
[RE03600(ALL)05/95]4.
Remove the other end of the positive (+) cable from the
discharged battery.
[RE03750(ALL)02/95]
If you need to replace your battery, seeBatteryin theServicing
Your Villagerchapter.
*
[RE03800(ALL)01/93]
Changing a Flat Tire
*
[RE03900(ALL)01/95]
If you get a flat tire while you are driving, do not apply the
brake heavily. Instead, gradually decrease the speed. Hold the
steering wheel firmly and slowly move to a safe place on the
side of the road. Park on a level spot, turn off the ignition, set
the parking brake, and turn on the hazard flashers.
File:12vxren.ex
Update:Tue Jun 4 11:42:14 1996