ECO mode Mercury Villager 1997 s User Guide

70(18ÊC) or 85ÊF (29ÊC).Then, the set temperature jumps 5ÊF and
stops at either60ÊF (16ÊC),which is maximum cooling, or90ÊF
(32ÊC),which is maximum heating.
[CF09850(ALL)05/96]
Changing the Display Mode (English/Metric)
[CF09860(ALL)03/96]
To switch between the English and Metric display mode, press
the DEFROST and A/C buttons simultaneously while rotating
the fan speed dial upward until it stops moving. After one
second, the display will begin to toggle between English and
Metric.
[CF09900(ALL)01/96]
Fan Speed and Thumbwheel
[CF09925(ALL)01/96]
The ATC automatically adjusts the fan speed to the existing
conditions. To control the fan speed yourself, use the
thumbwheel located at the extreme right side of the ATC
control panel. Using the thumbwheel cancels the automatic fan
speed control, and causes a
Hto appear in the display window.
Rotate the thumbwheel up for HI speeds and down for LO
speeds.
[CF09960(ALL)01/96]
To return to auto fan control, press the AUTOMATIC button.
[CF10000(ALL)01/96]
Airflow Function Selector Buttons
[CF10100(ALL)01/96]
Your ATC has five buttons which allow you to make special
selections for airflow. The buttons are grouped in the middle of
the ATC panel and allow you to determine airflow location.
Pressing any of the function selector buttons illuminates the
button pushed and directs airflow to the appropriate location.
The temperature of the airflow will still be automatically
controlled. Return to fully automatic operation by pushing the
AUTOMATIC button.
File:05vxcfn.ex
Update:Thu May 30 09:49:09 1996

Controls and Features
117
*
[CF75100(ALL)01/96]
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
[CF75200(ALL)01/96]
Replacement/Additional Transmitters
[CF75300(ALL)01/96]
In the event a transmitter is lost or an additional remote
transmitter needs to be set, you must change the ID code.
Follow the steps below to change the ID code of your system,
or return the remaining transmitter(s) to your dealer for
reprogramming of your remote entry system. This is necessary
to prevent unauthorized use of the lost transmitter.
[CF75400(ALL)01/96]
ID Code Programming Procedure
[CF75500(ALL)01/96]
NOTE: All transmitters must be programmed (or
reprogrammed) at the same time. If the programming
mode is entered and the transmitters are not
programmed (or reprogrammed) at the same time, they
will not operate with the system.
[CF75600(ALL)01/96]1.
Enter vehicle and close and lock all doors.
[CF75700(ALL)01/96]2.
Insert and remove key from ignition six times within ten (10)
seconds. The instrument panel lights will flash twice.
[CF75800(ALL)01/96]3.
Turn ignition key to the ACC position.
[CF75900(ALL)01/96]4.
Press the LOCK button on the remote transmitter once.
[CF76000(ALL)01/96]5.
To enter additional remote controllers (including the
original), unlock, then lock the driver's door using the power
door lock switch.
File:05vxcfn.ex
Update:Thu May 30 09:49:09 1996

130
[SS00190(ALL)01/96]
Rear Seat Cupholders (available on some models)
[SS00192(ALL)01/96]
Your vehicle may also have rear seat cupholders built into the
side panels.
[SS00194(ALL)01/96]
RWARNING
Objects stored on the ledges below the rear side
windows can become dangerous projectiles during a
sudden stop or collision. Put small objects only in the
storage compartments.
[SS00196(ALL)01/96]
Third Row Seat Storage Compartment (If equipped)
[SS00198(ALL)01/96]
Your vehicle may come equipped with a folding
cupholder/storage tray/storage compartment built into the
passenger's side of the third row seat. Find the indented ledge
on the right of the cupholder and pull it up to reveal the
storage compartment.
[SS00200(ALL)01/96]
Power Point Electrical Outlet (If equipped)
[SS00202(ALL)01/96]
Your vehicle may be equipped with a 12 volt power point
outlet located just below the rear seat audio controls. The power
point can be used in place of the cigarette lighter for optional
electrical accessories.
[SS00204(ALL)05/96]
NOTE: Do not plug the cigarette lighter into this power point
electrical outlet. Use the cigarette lighter.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

Seating and Safety Restraints
137
[SS11100(ALL)01/96]
NOTE: The second row two-passenger bench seat has a
unique safety restraint system. If your vehicle has the
two-passenger bench seat it is very important that the
unique safety belt system is used properly. Please
readAuxiliary safety restraint system for the second
row bench seatin this section, which explains the
unique safety belt system. Be sure that you
understand it before anyone rides in the
two-passenger bench seat.
[SS11115(ALL)01/96]
Passenger Outboard Lap/Shoulder Belts
[SS11117(ALL)01/96]
All seats except the driver's seat and the third seat middle
position are equipped with a dual locking mode retractor on the
shoulder belt portion of the lap/shoulder safety belt. (The
driver's seat has only a vehicle sensitive locking mode and the
third seat middle position has a lap belt without a retractor
Ðdescription follows.)
[SS11125(ALL)01/96]
Dual Locking Mode Retractors Operate in Two Ways:
*
[SS11130(ALL)02/96]
Vehicle sensitive (emergency) locking mode
*
[SS11140(ALL)01/96]
In this operating mode, the shoulder belt retractor will allow the
occupant freedom of movement, locking tight only on hard
braking, hard cornering or impacts of approximately 5 mph
(8 km/h) or more.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

156
%*
[SS15100(ALL)01/96]
Safety Seats for Children
*
[SS15200(ALL)01/96]
Use a safety seat that is recommended for the size and weight
of the child. Always follow the safety seat manufacturer's
instructions when installing and using the safety seat.
*
[SS15300(ALL)01/96]
Ford recommends the use of a child safety seat having a top
tether strap. Install the child safety seat in a seating position
which is capable of providing a tether anchorage. For more
information on top tether straps seeAttaching Safety Seats With
Tether Strapsin this chapter.
[SS15320(ALL)05/96]
When installing a child safety seat, be sure to use the correct
safety belt buckle for that seating position, make sure the
tongue is securely fastened in the buckle and there is tension in
the belt. For a shoulder/lap belt combination with a sliding
tongue, make sure the retractor is in the automatic locking
mode. For more information, seeUsing the Automatic Locking
Mode Retractor to Secure a Child Safety Seatlater in this chapter.
*
[SS15321(ALL)05/96]
All child restraint systems are designed to be secured in vehicle
seats by lap belts or by the lap portion of a lap-shoulder belt.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

Seating and Safety Restraints
159
[SS18250(ALL)01/96]
Using the Automatic Locking Mode
Retractor to Secure a Child Safety Seat
[SS19770(ALL)04/96]
Your vehicle is equipped with a dual locking mode retractor on
the shoulder belt portion of the combination lap/shoulder safety
belt for the front passenger seat and rear outer seats. The
automatic locking modemust be usedwhen installing a child
seat or infant carrier in the front passenger seat or rear outer
seats.
[SS19790(ALL)01/96]
To install a child safety seat or infant carrier, follow these steps:
[SS19830(ALL)01/96]1.
Position the child seat or infant carrier in the vehicle seat. If
you are using the moveable third row seat in the third row
position, the passenger side second row bucket seat, or the
front passenger seat, slide the seat to the rearmost position.
[SS19840(ALL)01/96]2.
Follow the child seat or infant carrier manufacturer's
instructions. Route the safety belt through the child seat or
infant carrier and insert the safety belt tongue into the
buckle until you hear and feel the latch engage. Be sure to
follow the child safety seat manufacturer's instructions for
belt routing.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

220
*
[GF07200(ALL)01/96]
You should always be careful when braking, even if your
vehicle has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
*
[GF07300(ALL)03/96]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[GF07310(ALL)03/96]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
[GF07350(ALL)01/96]
Ford Motor Company has not found any negative effects of
mobile radio transmitting equipment installed on vehicles with
the ABS system providing that the radio is installed according
to the radio manufacturer's instructions. However, if you have
had a mobile radio transmitter installed and the check ABS light
comes on (at any time other than immediately after turning the
key to the ON position) have your mobile radio dealer inspect
the installation. Also, if the ABS system is activated other than
during maximum braking, have your mobile radio installation
checked.
%*
[GF07400(ALL)03/96]
If Brakes Do Not Grip Well or Pedal is ªLowº
*
[GF07500(ALL)01/96]
If the brake pedal seems ªlowº it may indicate the need for a
brake system inspection and/or service. Apply your parking
brake several times. If the condition has not improved, you
should have your brakes checked as soon as possible.
%*
[GF07600(ALL)01/96]
Occasional brake squeal during light to moderate stops does not
affect the function of the brake system and is normal. However,
if the squeal becomes very loud or if it becomes more frequent,
return the vehicle to your dealer for inspection.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996

Driving
227
*
[GF10450(ALL)01/96]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
[GF10500(ALL)01/96]
If your vehicle is on an extremely slippery surface, the
Electronic Transaxle Control Module may receive a signal
indicating a rapid increase or decrease in wheel speed. If the
module detects this condition, it will limit the transaxle
operation to Third gear and Reverse. This reduces tire slippage
and protects the transaxle. The transaxle will operate normally
in Reverse, but will lack power during acceleration in Drive. If
this happens, stop your vehicle as soon as possible and turn the
ignition off for 3 seconds. Restart the vehicle. If the condition
still exists, contact your dealer as soon as possible.
*
[GF10550(ALL)01/96]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[GF10600(ALL)05/96]
When to use 2 (Second)
[GF10650(ALL)01/96]
Use Second (2) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second gear operation only. Do not exceed 68 mph
(110 km/h) in this position.
*
[GF10670(ALL)01/96]
When to use 1 (First)
[GF10700(ALL)01/96]
Use First (1) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to Second (2) or Overdrive (D). First (1) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to Second (2), and then
shift back to First (1) after the vehicle decelerates to the proper
speed. Do not exceed 35 mph (56 km/h) in this position.
File:09vxgfn.ex
Update:Thu May 30 09:54:10 1996

314
%*
[MC37300(ALL)01/96
]
Running Out of Fuel
*
[MC37350(ALL)08/95]
NOTE: Avoid running out of fuel because this situation may
have an adverse effect on modern powertrain
components.
*
[MC37400(ALL)01/96]
You may need to crank the engine several times before the fuel
system starts to pump fuel from the tank to the engine.
%*
[MC37450(ALL)03/96
]
Fuel Economy
*
[MC37500(ALL)01/96]
Fuel economy is an estimate of the efficiency of your vehicle,
and can be calculated as Miles Per Gallon (MPG) or Liters Per
100 Kilometers (L/100K).
*
[MC37550(ALL)01/96]
Do not calculate fuel economy during your vehicle's break-in
period. This would not be an accurate estimate of how much
fuel your vehicle will normally use.
*
[MC37600(ALL)01/96]
To calculate fuel economy:
*
[MC37650(ALL)01/96]1.
Fill the fuel tank completely and record the initial odometer
reading.
*
[MC37700(ALL)01/96]2.
Every time you buy fuel, record the amount (in gallons or
liters) purchased.
*
[MC37750(ALL)01/96]3.
After at least 3-5 tankfuls, fill the fuel tank and record the
final odometer reading.
*
[MC37800(ALL)01/96]4.
Use these equations to calculate your fuel economy:
*
[MC37850(ALL)01/96]
n
English: MPGU(total miles driven)V(gallons used)
[MC37900(ALL)01/96]
n
Metric: L/100kUMultiply the number of liters used by 100
and divide the answer by the number of kilometers
travelled.
File:11vxmcn.ex
Update:Mon Jun 10 15:17:05 1996

318
%*
[MC38590(ALL)03/96
]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
*
[MC38595(ALL)05/96]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is reset to a not ready
for I/M testing condition. To prepare for I/M testing, the law
specifies that additional mixed city and highway driving is
required to complete the check of the OBD II system.
*
[MC38602(ALL)03/96]
The driving modes required to reach the ready condition consist
of a minimum of 30 minutes of city and highway driving as
described below.
*
[MC38607(ALL)03/96]
n
20 minutes of driving in stop and go city-type traffic with at
least four idle periods.
*
[MC38612(ALL)03/96]
n
10 minutes of driving on an expressway or highway.
*
[MC38617(ALL)05/96]
Before completing the above driving modes, the engine must be
warmed up and at operating temperature. Once started, the
vehicle must not be turned off during the above driving modes.
If the vehicle owner is unable to meet the I/M requirements by
using these driving patterns, an authorized service center can
perform a detailed OBD II drive cycle as it would any other
type of repair work.
%*
[MC38700(ALL)03/96]
Lights and Bulb Replacement
*
[MC38800(ALL)01/96]
It is a good idea to check the operation of the following lights
frequently:
*
[MC38900(ALL)01/96]
n
headlamps
*
[MC38950(ALL)01/96]
n
high-mount brakelamp
*
[MC39000(ALL)01/96]
n
tail lamps
*
[MC39100(ALL)01/96]
n
brakelamps
File:11vxmcn.ex
Update:Mon Jun 10 15:17:05 1996