stop start Mercury Villager 1997 s User Guide

243
Roadside Emergencies
%*
[ER00101(ALL)01/96]
Hazard Flasher Switch
*
[ER00102(ALL)01/96]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[ER00104(ALL)01/96]
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these
lamps will flash on and off. The turn signal indicators cannot be
used when the hazard lamps are flashing. Operation of the
hazard flashers does not affect operation of the brakelamps.
*
[ER00106(ALL)01/96]
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the battery
excessively. If the flashers run for longer than two hours or if
your battery is not fully charged, your battery may be drained
to the point where the vehicle will not start.
[ER00108(ALL)01/96]
The hazard flasher switch is located on the instrument panel to
the right of the instrument cluster.
*
[ER00110(ALL)01/96]
To use the hazard flasher:
*
[ER00112(ALL)01/96]1.
Push the HAZARD switch; you will see the turn signal
arrows flash.
*
[ER00114(ALL)01/96]2.
To stop the hazard flashers, push the HAZARD switch again.
File:10vxern.ex
Update:Thu May 30 09:55:50 1996

244
[ER00116(ALL)01/96]
13-1/2 pica
art:0040078-D
Hazard flasher switch location
% [ER00150(ALL)04/96]
Fuel Pump Shut-Off Switch
*
[ER00155(ALL)05/96]
If the engine cranks but does not start or if you have had a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device that stops the fuel
pump when your vehicle has been involved in a substantial jolt.
*
[ER00160(ALL)05/96]
For information on how to check and reset the fuel pump
shut-off switch, seeFuel pump shut-off switchin the Index.
File:10vxern.ex
Update:Thu May 30 09:55:50 1996

318
%*
[MC38590(ALL)03/96
]
How to Prepare Your Vehicle for
Inspection/Maintenance (I/M) Testing
*
[MC38595(ALL)05/96]
In some localities it may become a legal requirement to pass an
Inspection/Maintenance (I/M) test of the On-Board Diagnostic
(OBD) II system. If the vehicle's powertrain system or its battery
has just been serviced, the OBD II system is reset to a not ready
for I/M testing condition. To prepare for I/M testing, the law
specifies that additional mixed city and highway driving is
required to complete the check of the OBD II system.
*
[MC38602(ALL)03/96]
The driving modes required to reach the ready condition consist
of a minimum of 30 minutes of city and highway driving as
described below.
*
[MC38607(ALL)03/96]
n
20 minutes of driving in stop and go city-type traffic with at
least four idle periods.
*
[MC38612(ALL)03/96]
n
10 minutes of driving on an expressway or highway.
*
[MC38617(ALL)05/96]
Before completing the above driving modes, the engine must be
warmed up and at operating temperature. Once started, the
vehicle must not be turned off during the above driving modes.
If the vehicle owner is unable to meet the I/M requirements by
using these driving patterns, an authorized service center can
perform a detailed OBD II drive cycle as it would any other
type of repair work.
%*
[MC38700(ALL)03/96]
Lights and Bulb Replacement
*
[MC38800(ALL)01/96]
It is a good idea to check the operation of the following lights
frequently:
*
[MC38900(ALL)01/96]
n
headlamps
*
[MC38950(ALL)01/96]
n
high-mount brakelamp
*
[MC39000(ALL)01/96]
n
tail lamps
*
[MC39100(ALL)01/96]
n
brakelamps
File:11vxmcn.ex
Update:Mon Jun 10 15:17:05 1996