ignition Mercury Villager 1997 s Owner's Guide

118
[CF76100(ALL)01/96]6.
Press the LOCK button on a new remote transmitter. The
instrument panel lights will flash twice, indicating code is
entered.
[CF76200(ALL)01/96]7.
Repeat steps 5 and 6 as needed (up to four remote
transmitters may be programmed).
[CF76300(ALL)01/96]
Anti-Theft System (If equipped)
[CF76400(ALL)05/96]
This system helps protect your vehicle against break-ins or theft
by monitoring all doors, the hood and the liftgate lock cylinder.
%*
[CF76500(ALL)01/96]
When an unauthorized entry occurs, the system triggers and
will:
[CF76600(ALL)01/96]
n
flash the headlamps and hazard lamps
*
[CF76700(ALL)01/96]
n
honk the horn
*
[CF76800(ALL)01/96]
n
disable the starting circuit to prevent the vehicle from being
started
[CF76900(ALL)01/96]
To arm the system
*
[CF77000(ALL)01/96]1.
Remove the key from the ignition.
[CF77100(ALL)05/96]2.
Lock the doors by using either the power door lock switch
or by turning the key in either the driver or passenger door
lock cylinder. The parking lights will flash and the horn
chirps to let you know that the system has been armed. The
anti-theft indicator light on the right side of the steering
wheel will light and remain on.
File:05vxcfn.ex
Update:Thu May 30 09:49:09 1996

120
[CF77600(ALL)03/96]
Disarming an untriggered anti-theft system
[CF77700(ALL)03/96]
Unlock either door with the door key or by pressing the
UNLOCK button on the remote keyless entry transmitter (if
equipped). This will disarm the system. When you unlock the
door with the key, make sure you fully rotate the key in the
lock. If you do not, the system may not disarm, and will trigger
when a door is opened.
[CF77777(ALL)05/96]
If the system is armed and you remain in your vehicle, simply
insert the key into the ignition and turn it to ACC. This disarms
the system and allows you to open the door to exit without
triggering the system. Remember to rearm the system by using
the power door lock or the remote transmitter (if equipped) to
lock the doors.
[CF77800(ALL)01/96]
The remote keyless entry system is designed to work with the
factory installed anti-theft system. It may not work with other
anti-theft systems.
[CF77900(ALL)01/96]
Triggering the anti-theft system
*
[CF78000(ALL)01/96]
The armed system will be triggered if:
[CF78100(ALL)03/96]
n
any door is opened without using the door key or the
remote keyless entry transmitter (if equipped)
[CF78200(ALL)01/96]
n
the liftgate is opened or unlocked
[CF78300(ALL)01/96]
n
the hood is opened
File:05vxcfn.ex
Update:Thu May 30 09:49:09 1996

Controls and Features
121
[CF78400(ALL)01/96]
Disarming a triggered anti-theft system
[CF78500(ALL)05/96]
The alarm can be disarmed by:
[CF78600(ALL)01/96]
n
unlocking the driver or passenger doors
[CF78700(ALL)03/96]
n
unlocking the doors with the remote keyless entry
transmitter (if equipped)
[CF78800(ALL)01/96]
n
putting the key in the ignition and turning it to the ACC
position
[CF78900(ALL)01/96]
NOTE: The flashing lights and honking horn will shut off
automatically within 2 minutes 30 seconds after the
system is triggered. It will trigger again if another
intrusion occurs. However, the starter circuit remains
disabled until the system is disarmed.
[CF79000(ALL)05/96]
NOTE: Factory installed remote keyless entry systems will
only operate with the ignition in the OFF position.
File:05vxcfn.ex
Update:Thu May 30 09:49:09 1996

126
[SS00140(ALL)01/96]
Using Power Seats (If equipped)
[SS00142(ALL)05/96]
If your vehicle has power front seats, you can adjust your seat
in several directions. The driver's seat can be adjusted in six
directions and the passenger's seat can be adjusted in four
directions. The power slide switch moves the seat forward and
rearward. The power seat height adjustment switch raises or
lowers the seat. The power recline switch tilts the seat toward
the front or toward the back. The controls are located on the
side of the seat closest to the door. The seat can be adjusted
even without the key in the ignition.
[SS00144(ALL)01/96]
13-1/2 pica
art:0040105-B
Six-way power seat controls location
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

146
%*
[SS13110(ALL)03/96]
Safety Belt Maintenance
*
[SS13120(ALL)02/96]
Check the safety belt systems periodically to make sure that
they work properly and are not damaged.
*
[SS13140(ALL)03/96]
All safety belt assemblies, including retractors, buckles, front
seat belt buckle support assemblies (slide bar) (if so equipped),
child safety seat tether bracket assemblies (if so equipped), and
attaching hardware, should be inspected after any collision. Ford
recommends that all safety belt assemblies used in vehicles
involved in a collision be replaced. However, if the collision was
minor and a qualified technician finds that the belts do not
show damage and continue to operate properly, they do not
need to be replaced. Safety belt assemblies not in use during a
collision should also be inspected and replaced if either damage
or improper operation is noted.
%*
[SS13200(ALL)05/96]
Air Bag Supplemental Restraint System
(SRS)
[SS13205(ALL)06/96]
THE SYSTEM MUST BE INSPECTED 10 YEARS AFTER DATE
OF MANUFACTURE SHOWN ON THE CERTIFICATION
LABEL, or if the ªairbagº lamp does not go on during ignition,
flashes intermittently, or remains on.
*
[SS13210(ALL)05/96]
Important Air Bag Precautions
*
[SS13220(ALL)05/96]
Your vehicle is equipped with a supplemental restraint system
designed to work with the safety belts to help protect you and
your right front seat passenger in the event of certain collisions
described in section ªHow Does the Air Bag Supplemental
System Work?º
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

Seating and Safety Restraints
153
*
[SS13430(ALL)05/96]
Determining If System Is Operational
*
[SS13440(ALL)05/96]
The Air Bag Supplemental Restraint System uses a readiness
light and a tone to indicate the condition of the system. The
readiness light is in the instrument cluster. When you turn the
ignition key to ON, this light will illuminate for approximately
six (6) seconds and then turn off. This indicates that the system
is operating normally. NOTE: Routine maintenance of the air
bag system is not required.
%*
[SS13450(ALL)05/96]
A problem with the system is indicated by one or more of the
following:
*
[SS13460(ALL)05/96]
n
the readiness light will either flash or stay lit,
*
[SS13470(ALL)05/96]
n
the readiness light will not light immediately after ignition is
turned on,
%*
[SS13480(ALL)05/96]
n
a group of five beeps will be heard. The tone pattern will
repeat periodically until the problem and light are repaired.
*
[SS13500(ALL)05/96]
If any of these things happen, even intermittently, have the Air
Bag Supplemental Restraint System serviced at your Ford or
Lincoln-Mercury dealer immediately. Unless serviced, the system
may not function properly in the event of a collision.
*
[SS13525(ALL)05/96]
Disposal of Air Bags and Air Bag Equipped Vehicles
*
[SS13550(ALL)05/96]
For disposal of air bags or air bag equipped vehicles, see your
local Ford or Lincoln-Mercury dealer. Air bags MUST BE
disposed of by qualified personnel.
File:06vxssn.ex
Update:Thu Jun 6 10:54:22 1996

211
Starting
%*
[TO04600(ALL)01/96]
Fuel-Injected Engines
*
[TO04700(ALL)01/96]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
*
[TO04750(ALL)01/96]
Starting Your Vehicle
%*
[TO04800(ALL)01/96]
Preparing to Start Your Vehicle
*
[TO04900(ALL)02/96]
RWARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open
the garage door before you start the engine.
*
[TO04950(ALL)01/96]
Before you start your vehicle, always:
*
[TO05000(ALL)01/96]1.
Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
*
[TO05100(ALL)01/96]2.
Make sure the headlamps and other accessories are turned
off when starting.
*
[TO05200(ALL)01/96]3.
Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
[TO05400(ALL)03/96]4.
Test the warning lights on the instrument cluster to make
sure they work. Refer to theInstrumentationchapter.
%*
[TO05700(ALL)01/96]
Starting Your Engine
*
[TO05800(ALL)01/96]
To start your engine:
*
[TO05900(ALL)01/96]1.
Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
*
[TO06000(ALL)01/96]2.
Keep your foot on the brake pedal and turn the ignition key
to ON.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

Starting
213
*
[TO07370(ALL)12/95]
NOTE: Your vehicle has an interlock that prevents you from
shifting out of P (Park) unless your foot is on the
brake pedal.
%*
[TO07500(ALL)01/96]
If the engine does not start after two attempts:
*
[TO07600(ALL)01/96]1.
Turn the ignition key to the OFF position.
*
[TO07700(ALL)01/96]2.
Press the accelerator all the way to the floor and hold it.
*
[TO07800(ALL)01/96]3.
Turn the ignition key to the START position.
*
[TO07900(ALL)01/96]4.
Release the ignition key when the engine starts.
*
[TO08000(ALL)03/96]5.
Release the accelerator gradually as the engine speeds up.
*
[TO08100(ALL)05/96]
If the engine still does not start, the fuel pump shut-off switch
may have been activated. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchin the index.
%*
[TO08200(ALL)01/96]
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast slightly
faster than its normal idle speed. It should, however, slow down
after a short time. If it does not, have the idle speed checked.
*
[TO08290(ALL)01/96]
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have
the vehicle checked.
*
[TO08300(ALL)01/96]
RWARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

Starting
215
*
[TO09020(ALL)03/96]
Once the shut-off switch is activated, you must reset the switch
by hand before you can start your vehicle.
[TO09025(ALL)01/96]
The fuel pump shut-off switch reset button is located below the
hood release handle.
[TO09030(ALL)01/96]
10-1/2 pica
art:0040048-C
Fuel pump shut-off switch reset button location
*
[TO09035(ALL)03/96]
RWARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
*
[TO09040(ALL)01/96]
If your engine cranks, but does not start after a collision:
*
[TO09045(ALL)01/96]1.
Turn the key in the ignition to the OFF position.
*
[TO09050(ALL)03/96]2.
Check under the vehicle for leaking fuel.
*
[TO09055(ALL)01/96]3.
If you do not see or smell fuel, push the fuel pump shut-off
reset button down. If the red button is already set, you may
have a different mechanical or electrical problem.
*
[TO09060(ALL)01/96]4.
Turn the ignition key to the ON position for a few seconds,
then turn it to the OFF position.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996

Starting
217
*
[TO10100(ALL)01/96]
Read the sectionClimate Control Systemsfor instructions on
bringing fresh outside air into your vehicle. Refer to the Index.
*
[TO11000(ALL)03/96]
Removing the Key From the Ignition
[TO11100(ALL)01/96]
OFF/LOCK is the only position that allows you to remove the
key from the ignition. The LOCK feature helps to protect your
vehicle from theft, because it also locks the steering wheel and
the gearshift lever when the key is removed.
%*
[TO11200(ALL)01/96]
If your key is stuck in the LOCK position, and you are unable
to turn it, move your steering wheel left or right until the key
turns freely.
*
[TO11250(ALL)01/96]
To remove your key from the ignition:
*
[TO11300(ALL)01/96]1.
Put the gearshift lever in P (Park).
*
[TO11400(ALL)01/96]2.
Set the parking brake fully.
*
[TO11500(ALL)03/96]3.
Turn the ignition key to LOCK.
*
[TO11600(ALL)03/96]4.
Remove the key.
*
[TO11700(ALL)01/96]
RWARNING
When you leave your vehicle, place the gearshift lever in
P (Park). Set the parking brake fully, and shut off the
engine. Never park your vehicle in N (Neutral). If you do
not take these precautions, your vehicle may move
suddenly and injure someone.
*
[TO11800(ALL)03/96]
RWARNING
Do not leave children, unreliable adults, or pets
unattended in your vehicle.
File:08vxton.ex
Update:Thu May 30 09:53:35 1996