engine overheat MINI COOPER 2010 Owners Manual

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
31
your MINI recommends that you have this work
done by your MINI dealer.
Windows
To prevent injuries, exercise care when
closing the windows.
Take the remote control with you when you
leave the car; otherwise, children could operate
the electric windows and possibly injure them-
selves.<
If, after a window is opened and closed
several times in close succession, the win-
dow can only be closed and not opened, the sys-
tem is overheated. Let the system cool for sev-
eral minutes with the ignition switched on or the
engine running.<
Opening
>Press the switch downwards.
The window opens until you release the
switch.
>Tap the switch downwards.
A s s o o n a s t h e r e m o t e is r e a d y , t h e w in d o w s
will open automatically. Tap the switch
again to stop the opening movement.
MINI: Closing
The window can be closed in the same way by
pressing the switch up.
MINI Convertible: Closing
In order to close the window, press the switch
up. The window closes until you release the
switch.
Electric power windows
initializing
If the battery was disconnected, e.g. for
changing batteries or vehicle storage,
reinitialize the power window switch; otherwise,
the windows will not be lowered.
MINI Convertible: Opening the convertible top is
not possible.<
1.Close the doors.
2.Open both windows.
3.Close both windows.
In the event of a system malfunction, please
contact your MINI dealer.
MINI Convertible: Central power
window unit
>Press the switch downwards.
First the rear windows, then the front win-
dows open until the button is released.
>Tap the switch downwards.
With ignition turned on: rear and front win-
dow open automatically.
Tap the switch again to stop the opening
movement.
To close the window, push the button upward
and hold.
Do not close the windows until the closing
procedure for the convertible top is fin-
ished. Otherwise, it is not ensured that the side
windows will close properly against the rubber
seals of the convertible top. Convertible top,
refer to page33.<

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
47
Starting the engine
Do not allow the engine to run in enclosed
areas; otherwise, inhalation of the noxious
exhaust gases can lead to loss of consciousness
and death. Exhaust gases contain carbon mon-
oxide, an odorless and colorless, but highly toxic
gas. Never leave an unattended vehicle with the
engine running; otherwise, such a vehicle repre-
sents a potential safety hazard.
Before leaving the car while the engine is run-
ning, place the transmission in neutral or move
the selector lever to position P and forcefully
apply the parking brake to prevent the car from
moving.<
Avoid frequent starting in quick succes-
sion or repeated start attempts in which
the engine does not start. Otherwise, the fuel is
not burned or inadequately burned and there is
a danger of overheating and damaging the cat-
alytic converter.<
Do not let the engine warm up with the vehicle
at a standstill. Move off immediately at a moder-
ate engine speed.
When starting the engine, do not depress the
accelerator pedal.
Manual transmission
Key in ignition lock or inside vehicle with Com-
fort Access, refer to page28.
1.Depress the brake.
2.Depress the clutch.
3.Press the start/stop button.
Automatic transmission
Key in ignition lock or inside vehicle with Com-
fort Access, refer to page28.
1.Depress the brake.
2.Shift the selector lever into position P or N.
3.Press the start/stop button.
The starter operates automatically for a certain
time, and stops automatically as soon as the
engine has started.
Switching off the engine
Always take the key with you when you
leave the vehicle.
When parking, apply the parking brake force-
fully; otherwise, the vehicle could begin to roll.<
Manual transmission
1.With the car at a standstill, press the start/
stop button.
2.Shift into first gear or reverse.
3.Forcefully apply the parking brake.
Automatic transmission
1.With the car at a standstill, move the selector
lever to position P.
2.Press the start/stop button.
3.Forcefully apply the parking brake.
Before driving into a car wash
By following these steps, the vehicle is able
to roll:
1.Place the remote control, even with Comfort
Access, in the ignition lock.
2.Depress the brake.
3.Move the selector lever to position N.
4.Switch off the engine.
Parking brake
The parking brake is primarily intended to pre-
vent the vehicle from rolling while parked; it
brakes the rear wheels.

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
93
with the road surface, so that the car cannot be
steered or braked properly.<
The risk of hydroplaning increases with declining
tread depth on the tires, refer also to Tread
depth on page113.
Driving through water
Drive through water on the road only if it is
not deeper than 1 ft/30 cm, and then only
at walking speed at the most. Otherwise, the
vehicle's engine, the electrical systems and the
transmission may be damaged.<
Parking brake on inclines
On inclines, do not hold the vehicle with
the clutch; use the parking brake. Other-
wise, greater clutch wear will result.<
For information on driving off using Hill Assist*,
refer to page66.
Braking safely
Your MINI is equipped with ABS. If you are in a
situation which requires full braking, it is best to
brake using maximum brake pressure. Since the
vehicle maintains steering responsiveness, you
can still avoid possible obstacles with a mini-
mum of steering effort.
The pulsation of the brake pedal, together with
the sound of hydraulic regulation, indicates that
ABS is actively taking effect.
Driving in wet conditions
When roads are wet or there is heavy rain, briefly
exert gentle pressure on the brake pedal every
few miles. Monitor traffic conditions to ensure
that this maneuver does not endanger other
road users. The heat generated in this process
helps dry the pads and rotors to ensure that
Then full braking force will be immediately avail-
able when it is needed.
Hills
To prevent overheating and the resulting
reduced efficiency of the brake system,
drive long or steep downhill gradients in the
gear in which the least braking is required. Even
light but consistent brake pressure can lead to high temperatures, brake wear and possibly
even brake failure.<
You can increase the engine's braking effect by
shifting down, all the way to first gear if neces-
sary. This strategy helps you avoid placing
excessive loads on the brake system. Downshift-
ing in manual mode of the automatic transmis-
sion, page49.
Never drive with the clutch held down,
with the transmission in neutral or with
the engine switched off; otherwise, engine brak-
ing action will not be present or there will be no
power assistance to the brakes or steering.
Never allow floor mats, carpets or any other
objects to protrude into the area around the
pedals; otherwise, pedal function could be
impaired.<
Corrosion on brake rotors
When the vehicle is driven only occasionally,
during extended periods when the vehicle is not
used at all, and in operating conditions where
brake applications are less frequent, there is an
increased tendency for corrosion to form on
rotors, while contaminants accumulate on the
brake pads. This occurs because the minimum
pressure which must be exerted by the pads
during brake applications to clean the rotors is
not reached.
Should corrosion form on the brake rotors, the
brakes will tend to respond with a pulsating
effect that even extended application will fail
to cure.
When the vehicle is parked
Condensation forms while the automatic climate
control is in operation, and then exits under the
vehicle. Traces of condensed water under the
vehicle are therefore normal.
In the MINI Cooper S, the coolant pump may
continue to run for some time after the engine is
switched off. This will generate noise in the
engine compartment.

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
131
3Plug and cable for the socket in the vehicle
interior, page89
4Holder for the sealant bottle
5Compressor
6Pressure gauge for indicating the tire infla-
tion pressure
7On/off switch
8Release button for reducing the tire inflation
pressure
9Connection hose to connect the compressor
and sealant bottle or the compressor and
wheel
Connector, cable and connection hose are
stored in the compressor housing.
Using the Mobility System
To repair a tire puncture with the Mobility Sys-
tem, proceed as follows:
>Fill the tire with sealant
>Distribute the sealant
>Correct the tire inflation pressure
Filling the tire with sealant
Proceed in the specified order; otherwise,
sealant may emerge under high
pressure.<
1.Shake the sealant bottle.
2.Pull the connection hose9 out of the com-
pressor housing fully and screw it onto the
connector of the sealant bottle. Make sure
that the hose is not kinked.
3.Insert the sealant bottle on the compressor
housing in an upright position.4.Unscrew the dust cap from the valve of the
defective wheel and screw the filling hose 2
of the sealant bottle onto the valve.
5.Ensure that the compressor is switched off.
6.Insert the plug 3 into the lighter socket/
power socket in the vehicle interior,
page89.
7.With the engine running:
Switch on the compressor and let is run for
approx. 3 to 8 minutes to fill the tire with
sealant and achieve a tire inflation pressure
of approx. 26 psi/180 kPa.
When the tire is being filled with seal-
ant, the inflation pressure may spo-
radically reach approx. 73 psi/500 kPa. Do
not switch off the compressor in this
phase.<
Do not run the compressor for longer
than 10 minutes; otherwise, the
device will overheat and possibly be
damaged.<
8.Switch off the compressor.
If an air pressure of 26 psi/180 kPa is not
reached:
1.Unscrew the filling hose 2 from the wheel
and drive the vehicle forward and backward
approx. 33 ft/10 m to distribute the liquid
sealant in the tire evenly.
2.Inflate the tire again with the compressor.
If an inflation pressure of 26 psi/180 kPa
still cannot be reached, the tire is too
heavily damaged. Please contact the nearest
MINI dealer.<
Detach the connection hose 9 and filling hose 2
from the sealant bottle connection and tire
valve.

Replacing components
132
Wrap the empty sealant bottle in suitable mate-
rial to avoid dirtying the cargo bay. Stow the
Mobility System back in the vehicle.
Distributing the sealant
Immediately drive approx. 3 mls/5 km to evenly
distribute the sealant.
Do not exceed speeds of 50 mph/
80 km/h.
If possible, do not drop below 10 mph/
20 km/h.<
Correcting the tire inflation pressure
1.After driving approx. 3 mls/5 km or ten min-
utes, stop at a suitable location.
2.Screw the connection hose 2 of the com-
pressor directly onto the tire valve.
3.Insert the plug 3 into the power socket in the
vehicle interior.
4.Correct the inflation pressure to 26 psi/
180 kPa. With the engine running:
>To increase the inflation pressure: switch on
the compressor. To check the current infla-
tion pressure, switch off the compressor.
Do not run the compressor for longer
than 10 minutes; otherwise, the
device will overheat and possibly be
damaged.<
>To decrease the inflation pressure: press the
release button 5.
If the tire cannot maintain the inflation
pressure, drive the vehicle again, refer to
Distributing the sealant. Then repeat steps
1to4.
If an inflation pressure of 26 psi/180 kPa still
cannot be reached, the tire is too heavily dam-
aged. Contact the nearest MINI dealer.<
Driving on
Do not exceed the permitted maximum
speed of 50 mph/80 km/h; doing so may
result in an accident.<
Replace the defective tire as soon as possible
and have the new wheel/tire assembly bal-
anced.Have the Mobility System refilled.
Changing wheels
Space-saver spare tire*
To change a space-saver spare tire, proceed as
follows:
>Remove the space-saver spare tire,
page133
>Prepare for tire change, page133
>Jack up vehicle, page134
>Mount space-saver spare tire, page134
>Tighten lug bolts, page134
>Drive with space-saver spare tire, page133
Tire change set for a space-saver
spare tire*
On vehicles with a space-saver spare tire, the
tire change set with onboard tools is stored
under the floor mat in the cargo bay.
1Chock, folding
2Hub cover remover
3Wheel stud wrench
4Vehicle jack
5Special wrench for removing the space-
saver spare tire
6Flat screwdriver/Phillips screwdriver
7Towing eyelet
8Lifting handle
The onboard vehicle tool kit includes a pouch
with a plastic bag in which you can place the
damaged wheel.

Indicator and warning lamps
142
Sliding/tilting sunroof or soft top of
MINI ConvertibleExcessive vehicle speed, activation
not possible, reduce speed and con-
tinue activation.
Lights up in red:
Control system for convertible top
failed!Position of convertible top and locking
mechanism not recognized. If con-
vertible top securely locked, drive
may be continued. Manually close
convertible top/sliding roof, refer to
page34. Have your MINI Service
inspect the system.
Lights up in yellow:
Drive of convertible top overheated! Let drive of convertible top cool down,
refer to page34.
Sliding/tilting sunroof or soft top of
MINI ConvertibleControl system of convertible top/tilt
roof malfunctioning. Close convertible
top/tilt roof manually, refer to
page34. Contact your MINI Service.
Tailgate of MINI Convertible not
closedClose the tailgate.
Gas cap missing or loose Make sure that the gas cap is correctly
positioned and close it until it audibly
clicks. Do not jam the strap between
the gas cap and the vehicle.
Window washer fluid level too low Add washer fluid as soon as possible,
page53.
Lights up in red:
Service due Arrange a service appointment.
Check service requirements,
page119.
Lights up in yellow:
The engine will start the next time the
start/stop button is touched, possibly
without the brake or clutch being
depressed
12Cause What to do

Indicator and warning lamps
144
Lights up in red:
Engine overheating Carefully bring the car to a stop,
switch off the engine and allow it to
cool down. Do not open the bonnet;
otherwise, there is a risk of injury from
scalding. Contact your MINI dealer.
Lights up in yellow:
Engine too hot Continue driving at more moderate
speed so that the engine can cool
down. Have the engine checked with-
out delay if the situation reoccurs.
Lights up in red:
Battery is no longer being charged.
Alternator malfunctionSwitch off all unnecessary electrical
consumers. Have the battery checked
without delay.
Lights up in yellow:
Battery charge level very low, battery
aged or not securely connectedHave the battery checked as soon as
possible.
Indication in US models
Parking brake applied
Indication in Canadian models
Parking brake applied
12Cause What to do

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
149
Lights up in red:
>Transmission limp-home pro-
gram active with restricted range
of gears, possibly with reduced
accelerationYou can continue your journey, but
moderate your speed and exercise
due caution. Have the system
checked without delay.
>Gears can be engaged without
depressing the brakeAlways depress the brake to engage a
gear.
>Automatic selector lever locked Manually unlock the selector lever
lock, page50.
Lights up in yellow: Have the system checked as soon as
possible.
>Automatic selector lever locked:
Selector lever locked in position P
with engine running and brake
depressed orManually unlock the selector lever
lock, page50.
>brake signal malfunctioning: gear
can be engaged without depress-
ing the brakeTo engage a gear while the vehicle is
at a standstill, always depress the
brake. Before leaving the vehicle,
move the selector lever to position P
and switch off the engine.
Lights up in red:
Transmission overheating Bring the car to a stop and move the
selector lever to position P. Allow the
transmission to cool down. You can
continue your journey, but moderate
your speed and exercise due caution.
Have the system checked if the situa-
tion reoccurs.
Lights up in yellow:
Transmission too hot Avoid high engine loads. You can con-
tinue your journey, but moderate
your speed and exercise due caution.
Selector lever position P not engaged.
Vehicle not prevented from rolling
12Cause What to do

REFERENCEAT A GLANCE CONTROLS DRIVING TIPS MOBILITY
163
Engine
– breaking in92
– data154
– overheated, refer to Coolant
temperature55
– speed154
– starting47
– starting, Comfort Access28
– switching off47
Engine compartment117
Engine coolant, refer to
Coolant118
Engine oil
– adding118
– additives, refer to Approved
engine oils118
– alternative oil types118
– approved engine oils118
– capacity118
– checking level117
– dipstick117
– intervals between changes,
refer to Service
requirements60
– MINI Maintenance
System119
Engine oil level, checking117
Engine output, refer to Engine
data154
Engine starting, refer to
Starting the engine47
Error messages, refer to Check
Control62
ESP Electronic Stability
Program, refer to Dynamic
Stability Control DSC65
Exhaust system, refer to Hot
exhaust system92
Exterior mirrors41
– adjusting41
– automatic heating41
– folding in and out41
External audio device87
Eyes
– for tow-starting and towing
away137
– for tying down loads96F
Failure messages, refer to
Check Control62
Failure of an electrical
consumer135
Fasten safety belts reminder,
refer to Seat belt
reminder41
Fastening safety belts, refer to
Safety belts40
Filter
– microfilter for air
conditioner82
– microfilter/activated-
charcoal filter for automatic
climate control84
Fine wood, care124
First aid pouch136
Fixture for remote control,
refer to Ignition lock46
Flash when locking/
unlocking23
Flat tire
– run-flat tires114
– Tire Pressure Monitor TPM69
Flat Tire Monitor FTM67
– indicating a flat tire68
– initializing the system67
– snow chains67
– system limits67
Flat tires, refer to Tire
condition113
Floor mats, care123
Fog lamps
– replacing bulb127,129
Folding rear seat backrest94
Folding roof, refer to
Convertible top with
integrated sliding sunroof32
Footbrake, refer to Braking
safely93
Footwell lamps78
For your own safety5
Front airbags72
Front fog lamps77,78
– indicator lamp140
– replacing bulb127Front seat adjustment37
Frost on windows, refer to
Defrosting windows82,83
FTM, refer to Flat Tire
Monitor67
Fuel103
– gauge56
– high-quality brands103
– quality103
– specifications103
– tank capacity158
Fuel clock, refer to Fuel
gauge
56
Fuel display, refer to Fuel
gauge56
Fuel filler flap102
– releasing in the event of
electrical malfunction102
Fuses135
G
Garage door opener, refer to
Integrated universal remote
control85
Gasoline
– refer to Average
consumption56
Gasoline display, refer to Fuel
gauge56
Gasoline, refer to Required
fuel103
Gear indicator
– automatic transmission with
Steptronic48
Gear shifting
– automatic transmission48
– manual transmission48
Gearshift lever
– automatic transmission with
Steptronic48
– manual transmission48
General driving notes92
Glass sunroof, electric30
– convenient operation22,24
– opening, closing30
– raising30
– remote control22

From A to Z
166
Oil consumption117
Oil level117
Oil, refer to Engine oil117
Oil types118
Old batteries, refer to
Disposal135
Onboard vehicle tool kit125
Opening and closing
– Comfort Access28
– from inside25
– from outside21
– using the door lock24
– via the remote control21
Opening and unlocking
– from inside25
Outlets
– refer to Ventilation84
Outlets, refer to Air vents80
Output, refer to Engine
data154
Outside temperature
display55
– changing unit of measure59
– on onboard computer59
Outside-air mode
– automatic climate control83
Overheated engine, refer to
Coolant temperature55
P
Paintwork, care122
Park Distance Control PDC64
Parking
– vehicle47
Parking aid, refer to Park
Distance Control PDC64
Parking brake47
Parking lamps, replacing
bulb127
Parking lamps/low beams75
Parts and accessories, refer to
Your individual vehicle4
Pathway lighting75
Personal Profile20
Pinch protection system
– windows32
Plastic parts, care124Pollen
– refer to Microfilter for air
conditioner82
– refer to Microfilter/activated-
charcoal filter for automatic
climate control84
Power convertible top32
Power failure135
Power windows31
Power windows, refer to
Windows31
Pressure monitoring of tires,
refer to Tire Pressure Monitor
TPM69
Pressure monitoring, tires67
– Flat Tire Monitor67
Pressure, tires104
Protective function, refer to
Pinch protection system
– windows32
Puncture
– Flat Tire Monitor67
R
Radio key, refer to Integrated
key/remote control20
Radio position, refer to Radio
readiness46
Radio readiness46
– switched off46
– switched on46
Rain sensor52
Range, refer to Cruising
range56
Reading lamps79
Rear fog lamp78
– indicator lamp140
– replacing bulb129
Rear lamps
– bulb replacement129
Rear lamps, refer to Tail
lamps128
Rear luggage rack97
Rear seat backrest, folding94
Rear seats
– folding the backrests94
Rear window heating81,83Rearview mirror, refer to
Mirrors41
Recirculated-air mode81,83
Recirculation of air, refer to
Recirculated-air
mode81,83
Reclining seat, refer to
Backrest38
Refueling102
Releasing
– bonnet116
Remote control20
– battery renewal30
– Comfort Access28
– garage door opener85
– malfunctions24,29
– service data119
– tailgate23
Replacement remote
control20
Replacing bulbs, refer to
Lamps and bulbs125
Replacing tires, refer to New
wheels and tires114
Reporting safety defects6
Reserve warning, refer to Fuel
gauge56
Reservoir for washer
systems53
Restraint systems
– for children43
– refer to Safety belts40
Reverse gear
– automatic transmission with
Steptronic49
– manual transmission48
Roadside Assistance136
Roadside parking lamps77
– replacing bulb127
Roadworthiness test, refer to
Service requirements60
Roof load capacity157
Roof-mounted luggage
rack97
Rope, refer to Tow-starting,
towing away138
RSC Runflat System
Component, refer to Run-flat
tires114